View Full Version : SX spur gear moving away from pinion under acceleration?
QuackingPlums
07-03-2010, 08:54 PM
Took my SX out for its first run today (yeah, I know... procrastination is my middle name :rolleyes:) and I ended up stripping the spur. :(
When I picked up the car and spun up the motor I could see the spur visibly moving away from the pinion! It's fine when I slow down again, so I'm thinking there are more than 3 screws I need to tighten to fix the mesh. I can see two underneath the rear bulkhead with the round heads, and the one behind the idler gears. There's one underneath the motor that I can reach through the slot in the chassis, though I gather that's just the motor clamp. They're all tight, so what's left? I haven't got a manual, so any suggestions before I go download one and find out the obvious for myself? :blush:
The car isn't brand new - I bought it off ebay and from what I can gather, it's only been run once or twice. Nowhere near enough to have bent a layshaft or anything... I hope!
Dazzler
07-03-2010, 09:01 PM
Sounds like the slipper may have been a little loose, leading to overheating of the spur and thus melting the centre. Concentricity is then lost. I'd take the spur off and have a look.
bigred5765
07-03-2010, 09:22 PM
or the layshaft bearings need replacing
burgie
07-03-2010, 09:57 PM
Sounds like the slipper may have been a little loose, leading to overheating of the spur and thus melting the centre. Concentricity is then lost. I'd take the spur off and have a look.
aye, this happened to me too - until I got the stegger layshaft!
mdb_75
07-03-2010, 10:15 PM
The new black spur gears that Schumacher are now supplying should stop this from happening..
mikeyscott
08-03-2010, 08:58 AM
The new black spur gears that Schumacher are now supplying should stop this from happening..
Or RW spurs
QuackingPlums
08-03-2010, 10:26 PM
Ok, I took the spur off and as suggested, the hole is melted. Layshaft doesn't look bent. The slipper was quite tight but I guess there's a lot of torque in those motors...
Where do I get the new black spurs? I can't see them on the Schumacher site. Have they filtered through to retailers yet?
David Church
08-03-2010, 10:36 PM
Ok, I took the spur off and as suggested, the hole is melted. Layshaft doesn't look bent. The slipper was quite tight but I guess there's a lot of torque in those motors...
Where do I get the new black spurs? I can't see them on the Schumacher site. Have they filtered through to retailers yet?
I Just ordered the spur wanted from Schumacher, the new stock are the black spurs, I had some delivered last week.:thumbsup:
But it wouldn't hurt to ask for a new black spur. But I am still using the old spur with no problem!
lochness42
09-03-2010, 01:59 PM
Black spur is running change as it was with Mi4LP and now with front reinforced wishbones for Cat
clintscreations
11-03-2010, 05:24 AM
You can bend a layshaft just from over tighting the slipper spring
Found out the hardway
QuackingPlums
24-04-2010, 11:54 PM
Got my new black spur gear on (finally!) - was just putting the idler gear cover back on and I noticed that there's a black rubber cover that covers....well nothing. It's the bit that the slipper adjust nut fits inside of, but there's no way of accessing the nut if the cover is fitted as it's sealed. Am I supposed to cut the end of this or something?
stegger
25-04-2010, 12:01 AM
Got my new black spur gear on (finally!) - was just putting the idler gear cover back on and I noticed that there's a black rubber cover that covers....well nothing. It's the bit that the slipper adjust nut fits inside of, but there's no way of accessing the nut if the cover is fitted as it's sealed. Am I supposed to cut the end of this or something?
In short YES :D
moth898
25-04-2010, 12:29 AM
Got my new black spur gear on (finally!) - was just putting the idler gear cover back on and I noticed that there's a black rubber cover that covers....well nothing. It's the bit that the slipper adjust nut fits inside of, but there's no way of accessing the nut if the cover is fitted as it's sealed. Am I supposed to cut the end of this or something?
Remove the rubber end plug and trim the plastic gear cover until you can catch the slipper nut with a rench, be careful not to trim to much that you can't set the rubber cap. I cut half of it off.
QuackingPlums
25-04-2010, 09:20 AM
Cool, cheers! :)
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.