PDA

View Full Version : Heavy Duty Adjuster TRF511


marco NL
22-04-2010, 07:38 PM
hi

hi where can I find Adjuster as if the picture

I can only find the orignal with this part number Tamiya - 51283

someone has a part number

I hope someone can help me

I am a TRF511 to build nou

Thanks guys

I'm sorry for my english i am dutch

DaveG28
22-04-2010, 08:40 PM
I don't think they have been released yet!

simoncrabb
23-04-2010, 10:50 AM
But there was a lot of them to be seen at Taly! :confused:

ramdrive
23-04-2010, 11:48 AM
Just mailed Champ on this very part, will let you know what they say.

P.S Cool blog Simon, just spent 4 hours reading it!

hi

hi where can I find Adjuster as if the picture

I can only find the orignal with this part number Tamiya - 51283

someone has a part number

I hope someone can help me

I am a TRF511 to build nou

Thanks guys

I'm sorry for my english i am dutch

marco NL
23-04-2010, 05:25 PM
thanks mate

I think they are only for team drivers are from Tamiya

You see them only at the team drivers cars




Just mailed Champ on this very part, will let you know what they say.

P.S Cool blog Simon, just spent 4 hours reading it!

B44&501xRacerEX
23-04-2010, 05:37 PM
Unless you want to bling up your ride, I do not see the point in the blue
turnbuckles. The stock steel ones are strong!
I think the car looks better with the silver turnbuckles...just my opinon.
Too much blue bling is a bad thing. The tottally destroys the look of the car.

AaronR
23-04-2010, 06:17 PM
...because everyone wants to know what you think about blue turnbuckles.

jhammond
23-04-2010, 07:22 PM
DELETED

marco NL
23-04-2010, 08:02 PM
not the turnbuckles but adjuster

cheers marco

Belsten
23-04-2010, 10:31 PM
But there was a lot of them to be seen at Taly! :confused:

I didnt notice any

Those blue turnbuckles give me a semi, im ordering some

marco NL
30-04-2010, 02:21 PM
nobody can help me :(

AaronR
30-04-2010, 05:22 PM
Most of us can help, but it will be without Tamiya ball studs and cups....

HPI studs (75115 & 75116) with Losi grey rigid cups (LOSA6016) are a great solution!

marco NL
03-05-2010, 08:16 PM
thanks mate




Most of us can help, but it will be without Tamiya ball studs and cups....

HPI studs (75115 & 75116) with Losi grey rigid cups (LOSA6016) are a great solution!

MHeadling
03-05-2010, 09:56 PM
Will a pack of each of the Hpi ball studs be enough to do a car??

Also will a pack of the losi ball cups do a car too?

Fredrik Emilsson
03-05-2010, 10:34 PM
I use LO-A-6015 (white Losi ball cups). 16 ball cups/pack.
Ball studs HB-61582 (13 mm) and HB-61581 (10.3mm). 8 ball studs/pack.

Or as Aaron said:
Losi grey rigid cups (LO-A-6016)=16 ball cups/pack.
HPI studs (75115 & 75116)=4 pieces/pack

I purchased from rcmodel.com.hk.

Tamiya grey ball cups should be available when TRF201 is released.

fastinfastout
04-05-2010, 03:46 AM
he wants to know how many sets of ball studs to buy

MHeadling
04-05-2010, 09:26 AM
I am just about to do an order, but how may packs of:

Ball studs HB-61582 (13 mm) and HB-61581 (10.3mm). 8 ball studs/pack.

Will I need to do the car??

Welshy40
04-05-2010, 10:11 AM
Kyosho ball cups fit on directly to the tamiya balls and is what i used on my 501x

simoncrabb
04-05-2010, 10:52 AM
Kyosho ball cups fit on directly to the tamiya balls and is what i used on my 501x

Yep, they do, the big long ones are nice n strong. I'm going to have them on mine when I get fed up of the kit black ones...

MHeadling
04-05-2010, 11:21 AM
Thats an easier option! Do you happen to know the part no??

simoncrabb
04-05-2010, 11:54 AM
Kyoshos Hard Ball End Set 97021H

There's 12 big uns and 4 tiny uns in the pack.

Welshy40
04-05-2010, 12:07 PM
UM112 but you will need to buy two lots for your car as there is only six long ones in each pack.

simoncrabb
04-05-2010, 12:32 PM
UM112 aren't the big long ones?

MHeadling
04-05-2010, 02:29 PM
Once I know what part no to order I think I am going the Kyosho route as the HB ball studs are a bit of a pain to get at the moment.

simoncrabb
04-05-2010, 02:43 PM
Kyoshos Hard Ball End Set 97021H

Google that part number and you'll see they should be what you want.

AaronR
04-05-2010, 03:30 PM
You can also use two of the very short Kyosho ball cups (that come with the set that Simon linked above) for the servo turnbuckle/linkage. They are the same length as the short Tamiya cups. :)

MHeadling
04-05-2010, 03:33 PM
Good stuff! I have just ordered a set up and see how they go!

Welshy40
04-05-2010, 04:31 PM
Kyoshos Hard Ball End Set 97021H

Google that part number and you'll see they should be what you want.

I didnt know about this one, thanks for that.

Something I can order as well instead of the normal ones, and looks better than UM112. Cheers.:thumbsup:

fastinfastout
08-06-2010, 05:41 PM
bump

are the new ball cups available to the public, which only the team drivers had access to?

want my 201x built right from the start, when I get it

AaronR
08-06-2010, 06:03 PM
I'll say it again...

HPI studs (75115 & 75116) with Losi grey rigid cups (LOSA6016) are a great solution!

fastinfastout
09-06-2010, 06:12 AM
I want tamiya ball cups on my 201x, as I already have tc5 ball studs/losi white ball cups on my current car.

Just changing to good ball cups is the easiest to achieve.

Does anyone have the part number for the trf ball cups?

Fredrik Emilsson
09-06-2010, 06:57 AM
201 comes with new grey ballcups. No need to change them.

BloodClod
09-06-2010, 08:55 AM
201 comes with new grey ballcups. No need to change them.

The part number in the TRF201 manual for the ball cups is the same as the ones previously used in the 511. I don't think these are newer ones unless tamiya made a running change without updating the part numbers?

fastinfastout
09-06-2010, 09:01 AM
yes and also the ball cups used on the 201x are the same as the db01, which everyone is swapping out for stronger ones.

maybe they will never be released

Fredrik Emilsson
09-06-2010, 10:14 AM
Trust me, 201 comes with new grey ball cups. Take a look in the 2wd thread.
Tamiya made a running change without updating the part numbers.
Here´s a pic:
http://i185.photobucket.com/albums/x168/joeglover13/DSC01787.jpg

carnage
19-07-2010, 09:44 AM
any ideawhere to get the "new" adjusters from, not the old ones considering they have the same part no.

TRF_AK
27-07-2010, 10:35 PM
Coming soon.....:thumbsup:

carnage
28-07-2010, 08:43 AM
Coming soon.....:thumbsup:
how soon:confused::confused::confused:

mattybucks
28-07-2010, 09:08 AM
I need some of these for Sunday's regional at DMS, as the kyosho ones I have on my 511 need replacing, are they in the country yet?

I know the hobby company still have the old ones, as I called them yesterday. Has anyone been using the old ones? What are they like?

If anyone has any spare then please pm me paypal waiting.

DaveG28
28-07-2010, 09:40 AM
I'm sure I'll be the only one to say this but....I prefer the old ones!! Have not popped a turnbuckle in over 6 mtgs with them! I have a feeling they just had a bad batch tbh..

carnage
28-07-2010, 10:20 AM
I need some of these for Sunday's regional at DMS, as the kyosho ones I have on my 511 need replacing, are they in the country yet?

I know the hobby company still have the old ones, as I called them yesterday. Has anyone been using the old ones? What are they like?

If anyone has any spare then please pm me paypal waiting.
do the 4.8mm kyosho adjusters fit on Tamiyas 5mm ball studs and work bind free
cheers
Steve

mattybucks
28-07-2010, 10:26 AM
do the 4.8mm kyosho adjusters fit on Tamiyas 5mm ball studs and work bind free
cheers
Steve


Yes they do, although I can't find any of those either.......

TRF_AK
29-07-2010, 02:59 PM
Should be out in Japan at least towards the end of next month. Item 54257.

Mouton
02-08-2010, 01:00 PM
I'm sure I'll be the only one to say this but....I prefer the old ones!! Have not popped a turnbuckle in over 6 mtgs with them! I have a feeling they just had a bad batch tbh..

I agree with you, so you are not alone. I have not had any problems at all with mine either on my TRF511. Although, when they do wear out, I will get the new type.