View Full Version : What fits?
Smartalec
26-04-2010, 05:58 PM
Can anyone tell me if these 501 parts fit the 511?
Diff outdrives and the diff pulleys
Driveshafts (front and rear)
Cheers :thumbsup:
Smartalec
26-04-2010, 06:56 PM
......and does the 501 slipper assembly fit too? :confused:
GRIFF55
26-04-2010, 07:00 PM
yes, yes as long as you get the right tooth pulleys, not sure and i think so!
Amish will be your best source mate
Smartalec
26-04-2010, 07:35 PM
yes, yes as long as you get the right tooth pulleys, not sure and i think so!
Amish will be your best source mate
Cheers matey, i've just acquired a 501 cheap and intend to rob the bits that fit as spares :thumbsup:
GRIFF55
26-04-2010, 08:01 PM
most i think alec. I'm gona call you mr Daley!!
simoncrabb
26-04-2010, 08:16 PM
Yes, diff outdrives are the same.
Driveshafts MIGHT be different - I think 511 ones are the WO ones, but the 501 ones aren't?!?
Smartalec
26-04-2010, 09:22 PM
most i think alec. I'm gona call you mr Daley!!
Cheers mate :lol:
Smartalec
26-04-2010, 09:23 PM
Yes, diff outdrives are the same.
Driveshafts MIGHT be different - I think 511 ones are the WO ones, but the 501 ones aren't?!?
What's WO mean then Simon? :confused:
Smartalec
26-04-2010, 09:24 PM
I'm just going to strip it down and have a look :)
Fredrik Emilsson
26-04-2010, 09:29 PM
Correct.
Different driveshafts, but 501X fits 511 and vice versa.
The 511 drive shafts are the DB01 WO (Wide Operating Angle) drive shafts.
Front upright for WO front drive shaft is different (950 inner bearing).
Most 501X parts fit 511. Damper towers, pulleys, belts, outdrives, suspension arms, dampers, caster blocks, rear hubs etc.
Chassi, upper decks, bulkheads (front, rear, center), camber mounts and rear (front) suspension mount are different. 501X Rear (rear) suspension mount is also different, but fits 511. The 501X has less toe-in.
I had a lot of spare parts for my 501X WE, so when I got the 511 I only purchased new spare drive belts (reinforced ones), high traction arms and front uprights (for WO drive shaft).
lewis
26-04-2010, 09:32 PM
What's WO mean then Simon? :confused:Wrong ones:)
Smartalec
27-04-2010, 04:51 AM
Wrong ones:)
I bet that took you all night to come up with that one didn't it? :D
Smartalec
27-04-2010, 04:53 AM
Correct.
Different driveshafts, but 501X fits 511 and vice versa.
The 511 drive shafts are the #54119 DB01 WO (Wide Operating Angle) drive shafts.
Front upright for WO front drive shaft is different (950 inner bearing).
Thanks Fredrik, so am I right in saying that the rear driveshafts are the same on both cars?
Fredrik Emilsson
27-04-2010, 06:36 AM
Sorry, I only wrote part nr. for rear drive shafts.
TRF511 has the #54119 DB01 Assembly WO Univ Shaft - Wide Operating Angle (Rear) and the #54118 DB01 Assembly WO Univ Shaft - Wide Operating Angle (Front).
501X does´nt have these, but they fit on both DB01, 501X and 511.
So the 501X standard drive shafts also fit the 511.
simoncrabb
27-04-2010, 09:58 AM
I've also found you can run the front WO driveshafts on normal '10' front hubs by using a 10x3x5mm bearing on the inside.
Esky do some for some helicopter that I use.
That in turn means I can use alloy GPM front hubs on both db01 and 511.
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.