PDA

View Full Version : Cougar SV diff troubles!


bumrar
03-05-2010, 09:29 AM
well, didn't have the best of starts with my cougar this weekend - only managing to finish two heats at Bury metro due to the diff unwinding itself and the circlip coming out of its groove. When it did go tho, it was superb! waaay waaay better than my tired xxx!. Another guy pitting near me was having the same problems with his. Is this a common issue? quality issue with the parts maybe? or just the numpty assembling it?

Regards,

Ste

slow bob
03-05-2010, 09:34 AM
I think the team drivers have done a fix for the diff problem in one of the cougar setup threads

must be a common problem :(

Mossy
03-05-2010, 09:43 AM
You have to be carefull when putting the Circlip in.

Before you put the circlip into the diff outdrive, make the circlip wider i.e spread the actual width of the shortest point. When you put it into the diff halve, it needs to be a very tight fit - you shouldnt be able to even rotate it with a small screw driver. When it is this tight you wont have anymore problems.

Si

bigred5765
03-05-2010, 10:49 AM
in the new instruction manual that was with your kit there a page floating around the front page, explains it all in detail if built right you should have no issues, if your having probs at southport next time come see me ill take a look for you

DCM
03-05-2010, 10:51 AM
so the groove has been machined to deep?

Cockerill
03-05-2010, 11:02 AM
I think it's more a tolerance issue as there only seems to be a few people experiencing the issue.

You should have come over and seen one of the Schumacher guys, any of us would have had a look over it for you :thumbsup:

simoncrabb
03-05-2010, 11:17 AM
No problems here!

I don't have any fancy circlip pliers, so my bodge it in method worked well, the circlip was nice and tight.

I'm not sure how I'm going to get it out again but hey ho...

bigred5765
03-05-2010, 01:22 PM
so the groove has been machined to deep?
not really the one i saw yesterday they had squashed the cir-clip to much when installing it, so it was sloppy,buy slightly stretching it before you install it your counteracting this,

mikeyscott
03-05-2010, 01:45 PM
not really the ones i saw yesterday they had squashed the cir-clip to much when installing it, so it was sloppy,buy slightly stretching it before you install it your counteracting this,

Didn't have any probs, but I think I'll give it a check this week.

bigred5765
03-05-2010, 02:01 PM
if the cars running fine i wouldnt worry, the one a saw on sunday was plain as day circlip squashed,

mikeyscott
03-05-2010, 02:12 PM
if the cars running fine i wouldnt worry, the one a saw on sunday was plain as day circlip squashed,

Ok cool. Just found the extra page. D'oh as I used the PDF from the website so the manual didn't get mucky

Jonesy
03-05-2010, 02:55 PM
I knew of some other team drivers having issues early on and until yesterday my diffs were fine. Had one go on me at the Mid-West Regional yesterday and that was the same diff that I'd ran in the car for well over 100 minutes of racing.

The build is key as Mossy mentions but as with any maintenance I would check the diff every so often to save future issues

bumrar
03-05-2010, 06:45 PM
in the new instruction manual that was with your kit there a page floating around the front page, explains it all in detail if built right you should have no issues, if your having probs at southport next time come see me ill take a look for you


ah yes- that bit of paper I discrded! oops! I did try opening the circlip up before installation, but then wasn't taking much care not to squeeze it more than needed, this, and putting it in and taking it out several times could be the problem. Got some new parts on the way, so I'll take more care when assembling it next time.

Thanks for the help guys

Ste

bigred5765
03-05-2010, 07:32 PM
ste was u the guy that came to see me at bury, u lent my c lip pliers

bumrar
04-05-2010, 07:47 AM
ste was u the guy that came to see me at bury, u lent my c lip pliers


nope, that wasn't me, could have been the chap pitting near me tho with a green cougar I think it was having the same problem

sime46
04-05-2010, 08:18 PM
Ran mine today on our local indoor carpet track for well over 20mins constant without any probs at all. Brought it home and stripped it for inspection and all is well. Handled beautifully too! Very chuffed.:D:D

Michiel H.
05-05-2010, 08:18 AM
My circlip is loose too, i tried making it fit tight but failed.:(

i just can't get it in without pushing it's legs against eachother.

Any advice? dont want to kill my diff first time out.

bigred5765
05-05-2010, 09:38 AM
take it out and stretch as per paper insert in the manual, then when fitting it don't use the c lip pliers but don it buy hand, use a flat screw driver and do it one side at a time push one side half way down or so, then push other side in a little bit at a time so as not to twist it, when you here a click you no its in and make sure it isn't easy moved with he screwdriver,it should be hard or impossible to turn.

Michiel H.
05-05-2010, 09:40 AM
i'll try that then. thanks.:thumbsup:

mikeyscott
05-05-2010, 03:36 PM
Just wondering what diff balls come with the SV?

JohnM
05-05-2010, 03:39 PM
round ones:woot:

Michiel H.
05-05-2010, 04:01 PM
Ceramic ones, trust aswell.:D

Stupid circlip tough, can't get mine right.:(

simoncrabb
05-05-2010, 04:12 PM
Just wondering what diff balls come with the SV?

Err, from the manual:

Ceramic Nitride Diff Balls 2.5mm (pk12) U3019

Albertini
05-05-2010, 08:59 PM
Stupid circlip tough, can't get mine right.:(

Having trouble here too, a bit too fiddly. Got it in and it dosen't rotate or move easily but it did a little when I applied a little pressure with a small screw driver.
Only got one clip so its going in. Not a great bit of design this bit otherwise all good.

bigred5765
05-05-2010, 10:17 PM
its not a worry and is exactly the same as the cat sx, as long as you build it right it give many hours of trouble free racing, and is a simple neat idea that works just fine,

fastinfastout
11-05-2010, 06:56 AM
Err, from the manual:

Ceramic Nitride Diff Balls 2.5mm (pk12) U3019
can you use 3/32 (2.38mm) diff balls?

2.5mm is an odd diff ball size:eh?:

MattW
11-05-2010, 09:10 AM
I very much doubt you can use 3/32. I have checked in this diff, but did once look into it for the touring car diffs and it wasn't possible then - and there doesn't feel like there is enough side movement to allow for a smaller ball.

2.5mm isn't hugely odd - and it's a Schumacher part. As well as some other aftermarket diff ball sellers that i've seen.

j0pp3
12-05-2010, 12:39 PM
I found a very cheep circlip plier (approx $3) and opened it up slowly so that the space was 4.5mm as stated in the attached paper.

Then carefully fitted it in one side at a time. The hardest part was in the beginning and the clip flew away a few times :lol: Then I took a transparent plastic bag and wrapped it over the diff and my hand so it couldn't go very far :thumbsup:

Take your time. This is an important step while building.

Happy racing!

/j0pp3 (RC-newbie)

racingdwarf
18-06-2010, 09:29 AM
well just reading this thred, as I am rebuilding a club members sv diff as it is driving him mad, the circlip was loose:(.tried stretching, but still loose, will order another.

I have to say altho some may think this is a great design, im not sure myself, To me good design is simple and effective,and easy for people of all abilitys to build...At the min my B4 is safe:thumbsup:

ant west 71
22-06-2010, 09:53 AM
no problems here either, as ive not got the pliers for these, so i started the one end of the clip and just rotated it around working it down into the groove with a strong needle in the leading hole. never had a problem yet and that is after 4 meetings.