View Full Version : Cougar Quality Problems...
burgie
09-05-2010, 04:52 PM
I am experiencing a couple of problems with my Cougar, and it's really not impressing me.
I have (so far) had two drive shafts (both on the left side coincidentally) fall completely apart. neither of them have lasted more than five laps. I have checked the diff for binding, and it's free as could be. i have also checked the droop on the back to make sure it's not excessive and that's fine too.
What else should I be looking for to try and stop this happening?
Also, I have noticed that the anodizing inside the shocks is coming off, making the shocks a tiny bit "notchy" where the anodizing has got between the piston and the shock body (i presume) scratching the inside of the shock body. Is there anything I can do to stop the anodizing from coming off?
Finally, the gearbox moulding doesn't seal properly on my car, nor on the other cars I have seen at the club - so grit and dust (and moisture no doubt) can find it's way in - I can actually see the gears in the 'box from the outside!
I am a little disappointed thus far with the car - I haven't even managed to race it yet, as both drive shafts have failed during practice, well if you can call under 10 laps in two weeks practice. :thumbdown:
moth898
09-05-2010, 04:57 PM
what do you mean when you say the driveshafts fall apart? does the universal joint come apart or does the dogbone side come out of the drive yokes? I'm a little confused about the anodizing because it's not thick enough to peel off, its more likely to wear off.
mikeyscott
09-05-2010, 04:59 PM
Have you spoken to Schumacher themselves?
janus_77
09-05-2010, 05:06 PM
what do you mean when you say the driveshafts fall apart?
The universal joint comes apart, the pin just comes loose in a couple of shafts.
Seems to be "hit and mis", some cars dont have this issue at all. But some.....
burgie
09-05-2010, 05:07 PM
when the drive shafts fall apart, the gold bit in the middle and the pins fall completely out, the out drive has been slightly damaged as well, as the drive shafts exits the car.
I have spoken to Schumacher and the response was "yes that's happened to some during testing". They did replace the first driveshaft FOC without any quibble though, I should say.
Alfonzo
09-05-2010, 05:10 PM
Well that's a contrast to my post regarding the quality of the kit! :D
Looking at mine, there's no way I can see into the gear box through the join line, bit odd?
Hopefully just a degree of bad luck and teething problems Chris?:confused:
spud31
09-05-2010, 05:16 PM
Chris i can sympthise my cougar cant be run due to a mismoulded pair of gearbox housings the layshaft is reallt stiff when turned.
I phoned schuy an spoke to chris on friday an a new pair are on there way :thumbsup:
ian h
09-05-2010, 05:52 PM
Chris i can sympthise my cougar cant be run due to a mismoulded pair of gearbox housings the layshaft is reallt stiff when turned.
I phoned schuy an spoke to chris on friday an a new pair are on there way :thumbsup:
My moulded gear box halves are not the best either, had to do a bit of work to get them to marry up and also had to run in the layshaft and idler gears using a dremel connected to the layshaft until it eventually bedded in and ran smooth. On a positive note the rest of the kit is fine and I got a third place finish today in my first outing with the cougar. The handling is super!
Tom3012
09-05-2010, 06:29 PM
Could be because they're the first batch? My gearboz housing is the same, i can see the gears, also i had odd length rear turnbuckles, schumacher are sending out a replacement though... I also found out today my kit didnt come with the 4 purple washers that can be used to screw the top plate down to make it stiffer, need to email them again and see what they say
Albertini
09-05-2010, 06:34 PM
The tranny housings on mine leave a small gap at the back aswell, thought I'd misassembled at one stage as its got a tight spot(think its gone now after running it for 2 mins up the drive).
You can see the gap in this picture.
http://www.oople.com/rc/photos/2010national-talywain/2wdgallery/DSC_1910.html
If you look at the pictures on the schumacher site of the gearbox, above the motor is a small purple washer spacing the front of the 2 halfs apart. This washer is not shown in the instructions and funnily enough I had two left over but didn't know what they were for. I haven't taken it all apart to put these in but could it make a difference??
Having said all of this, I love this car, it has real character, which is why I bought it. Wish I could afford another and have one as a shelf queen, its just beautiful.:thumbsup:
purplenut
09-05-2010, 07:35 PM
Question,what shocks are you running on this?
Cheers
Similar gearbox issues here, mismatched case halves and a noticable tight spot. One seems to have gone after running a pack through the car and a bit of electrical tape sorted the other.
Along with the cheese turnbuckles, slightly disappointing for an otherwise excellent build of a premium car.
JustARcFan
09-05-2010, 07:43 PM
My build was perfect, no gaps at all and the smoothiest transmission.
Just waiting for the missing pieces to arrive. :woot:
wouter.z
09-05-2010, 07:59 PM
I had simular problems with mine. I had to dremmel a bit out of the transmission housing (around the idler) to get the transmission smooth. And i must admit it still isn't perfect.
Albertini
09-05-2010, 07:59 PM
Purplenut, thats not a picture of my SV, thats Jimmys photo of the other version thats not out yet. Sorry I made it sound like the photo was of mine, its not, it just has the same gap as this one.:)
Was thinking the same as you P.B. and will just put a small bit of tape over it.:)
jeffrey
09-05-2010, 08:13 PM
i also have a small gap, but my transmission turn not so good.
if i turn the spur gear, there is one place it turns a little bit stiff.
now i'm a bit worried to drive with it.
i have heard that dremel it a bit would help, but what must i dremel away?
thanx
grtz jeffrey
Jonathan
09-05-2010, 09:27 PM
Build not finished, but gap in gearbox housing and stiff points on idler here too.
moth898
10-05-2010, 12:58 AM
when the drive shafts fall apart, the gold bit in the middle and the pins fall completely out, the out drive has been slightly damaged as well, as the drive shafts exits the car.
I have spoken to Schumacher and the response was "yes that's happened to some during testing". They did replace the first driveshaft FOC without any quibble though, I should say.
I can't say anything about the universals coming apart...I've never seen that. There is a glue thats called cold weld that supposedly is as strong as welding, maybe a touch of this on the pin will help keep it in place.
If the universals are falling out of your drive yokes its usually due to the setup. If your running the rear shock setup check the suspension geometry... the same thing happend to my Cat until I lower the rear arm toe in by one degree and added the aluminium rear hubs with the 1 degree built in, it hasen't happened since. I like the shaft to be 2 mm into the drive yokes at minimum.
burgie
10-05-2010, 08:00 AM
the driveshafts are only falling out of the yokes because the universal joint keep falling apart....:thumbdown:
I am "glad" to see it's not just my Cougar with the gearbox problem I have also mentioned. But it's not what you expect on a near £250 kit.
mikeyscott
10-05-2010, 08:02 AM
Give Schumacher a call and I'm sure they'll sort you out.
I have seen a number at our track with no probs at all.
burgie
10-05-2010, 08:29 AM
I have just been on to Schumacher.
They are aware that there is an issue with some of the driveshafts falling apart, and are sending me a replacement one out today, so no complaints there.
I am sure once these problems are sorted out with my car it will be all good - I couldn't catch Tom Pattison at Southport yesterday with his, and I was running 4wd! :blush:
mikeyscott
10-05-2010, 08:34 AM
Good to hear :)
Yeah our quick guy at our track is getting close to the 4WD track record with his!
Timee80
10-05-2010, 05:42 PM
Took the cougar out yesterday for its first run and it drove really well. Performance wise i was really impressed but wasnt too keen on the quality of the turnbuckles. The 2 front camber link turnbuckles both bent at about 45 degrees at the bendy ball cup end, and then a rear bent as well in a seperate heat with no accidents:eh?:
I rang schumacher to see if there was any quality issues with these and they said they know of none, and that their turnbuckles are as hard as any of their competitors.
Anyone experienced turnbuckles made of cheese???
bigred5765
10-05-2010, 06:08 PM
no quality issues there made of steel, just replace with purple ti ones :) Yeah 6000 posts
mikeyscott
10-05-2010, 06:10 PM
no quality issues there made of steel, just replace with purple ti ones :) Yeah 6000 posts
I've ordered mine and the kit ones will be spares for me or other SV racers :)
Was going to order an SX2 C/F, but they don't come with titanium turnbuckles :( etc. which bumps the price back up
Anyone experienced turnbuckles made of cheese???
Not 'experienced' them as the team drivers simply told me not to bother. This Cougar lark gets damned expensive after Ti turnbuckles, camber link options etc!
Jamesk
10-05-2010, 07:37 PM
Intersting to hear peoples veiws and teething problems, think ill wait for TRF201x and the decide what to buy
Gearbox. I have used some wet and dry sand paper on a very flat surface and sanded the high spots of the off the moundings, thus helping the fit and reducing the gap between the two halfs.
Don`t take to much off or you`ll make the layshaft and idle gears bind.
Took the cougar out yesterday for its first run and it drove really well. Performance wise i was really impressed but wasnt too keen on the quality of the turnbuckles. The 2 front camber link turnbuckles both bent at about 45 degrees at the bendy ball cup end, and then a rear bent as well in a seperate heat with no accidents:eh?:
I rang schumacher to see if there was any quality issues with these and they said they know of none, and that their turnbuckles are as hard as any of their competitors.
Anyone experienced turnbuckles made of cheese???
:lol::lol::lol:Gafer tape Tim:lol::lol::lol:
eichkay
10-05-2010, 11:35 PM
Gearbox. I have used some wet and dry sand paper on a very flat surface and sanded the high spots of the off the moundings, thus helping the fit and reducing the gap between the two halfs.
Don`t take to much off or you`ll make the layshaft and idle gears bind.
I might take mine apart before i get to far into the building just to double check it sits flat... once assembled the gear box shows the gap no matter which order i did the screws up.. but once installed on the car and removing the spru burs off the diff cups housings i cant see a gap at all ..
i thought i did see a gap last night just under the camber link, but after looking again today i cant see a gap at all anywhere.
during assembly ..
http://i235.photobucket.com/albums/ee146/eichkay/Schumacher/GEARBOX.jpg
I did come across a crushed ball stud in the first packet i opened for the build... had to raid my parts bin.
http://i235.photobucket.com/albums/ee146/eichkay/Schumacher/faulty-ballstud.jpg
fastinfastout
11-05-2010, 05:00 AM
thats some pretty bad QC at schu.
I have never seen a ball stud like that before, not even in the cheapest kits.
im starting to have 2nd thoughts now, knowing how dodgy this car is/can be.
does the original cat sx have ti turnbuckles? if not, are they the same as the SV's?
It looks like there is some tweaking of the moulding when it is cooling, with the gearbox.
As for the ball stud, I have seen that in other kits too, they can't physically check every metal piece like screws and such.
MattW
11-05-2010, 09:08 AM
You want them to check every ballstud thread, seriously?? How much are you prepared to pay for the kit?? Sadly the odd one will always slip through, same for every single kit manufacture.
eichkay
11-05-2010, 09:31 AM
thats some pretty bad QC at schu.
I have never seen a ball stud like that before, not even in the cheapest kits.
im starting to have 2nd thoughts now, knowing how dodgy this car is/can be.
does the original cat sx have ti turnbuckles? if not, are they the same as the SV's?
the ball stud is obvious it must have stuck in the thread machine as its been crushed .. rather impressive IMO.. and a pain in the bum at the same time.
Ive pulled my diff housing down and sanded it back a bit.. taken very little off, using 1200 grade wet and dry.. the 3 screw sections seem to have ever so slight differences and wont allow the other housing bits to sit flush, after a very little skims over some glass with sand paper on it the housing sit nice and flush and went back onto the car perfect. Its a model after all, some fit and finish work on such a new item maybe required.
moth898
11-05-2010, 09:50 AM
We all rushed them to give use the car so little problems like this will happen...they'll be corrected in the near future for sure. But if Cockril and Moss can win with it, it can't be that bad:thumbsup:
reelman_fishing
11-05-2010, 11:31 AM
I am experiencing a couple of problems with my Cougar, and it's really not impressing me.
I have (so far) had two drive shafts (both on the left side coincidentally) fall completely apart. neither of them have lasted more than five laps. I have checked the diff for binding, and it's free as could be. i have also checked the droop on the back to make sure it's not excessive and that's fine too.
What else should I be looking for to try and stop this happening?
Also, I have noticed that the anodizing inside the shocks is coming off, making the shocks a tiny bit "notchy" where the anodizing has got between the piston and the shock body (i presume) scratching the inside of the shock body. Is there anything I can do to stop the anodizing from coming off?
Finally, the gearbox moulding doesn't seal properly on my car, nor on the other cars I have seen at the club - so grit and dust (and moisture no doubt) can find it's way in - I can actually see the gears in the 'box from the outside!
I am a little disappointed thus far with the car - I haven't even managed to race it yet, as both drive shafts have failed during practice, well if you can call under 10 laps in two weeks practice. :thumbdown:
I'm also experiencing the same with my sons shocks, after three rounds of racing the front shock started to leak so I took the top of the shock to refill it I noticed allot of metallic bits floating around inside, so I cleaned all the oil out and noticed the inside was marked. So I just filled back up with oil and finished the days racing, phone Schumacher on the Monday and explained what had happened and on the Tuesday a parcel with two brand new shock body’s and a set of seals, NOW THAT IS WHAT I CALL SERVICE. As with all new products there will be teething problems so just be patient. Real car manufacture can’t get it right look at Toyota!!!
Anyway it’s a big thumbs up for shumacher from me:thumbsup::thumbsup::thumbsup::thumbsup:
PsycoChris
11-05-2010, 12:37 PM
Here is another Issue with my steering.
I am using a JR 9100s Servo. With the stock servo horn they supplied. It is hitting the Inside of the Nose and Binds for a split second. Anyone else having this Issue.
http://img.photobucket.com/albums/v612/killatoyota4569/013-27.jpg
http://img.photobucket.com/albums/v612/killatoyota4569/014-22.jpg
bigred5765
11-05-2010, 12:40 PM
Chris the problem with your steering is pretty a easy one remove the purple washers there not supposed to be there,
bigred5765
11-05-2010, 12:47 PM
I might take mine apart before i get to far into the building just to double check it sits flat... once assembled the gear box shows the gap no matter which order i did the screws up.. but once installed on the car and removing the spru burs off the diff cups housings i cant see a gap at all ..
i thought i did see a gap last night just under the camber link, but after looking again today i cant see a gap at all anywhere.
during assembly ..
http://i235.photobucket.com/albums/ee146/eichkay/Schumacher/GEARBOX.jpg
I did come across a crushed ball stud in the first packet i opened for the build... had to raid my parts bin.
http://i235.photobucket.com/albums/ee146/eichkay/Schumacher/faulty-ballstud.jpg
on the gearbox gap issue and tight spot,
remove the slipper assembly and back of the three screws that hold the gearbox half's together, leave them loose and remount the gearbox top on the chassis again tighten it down then re tighten the three screws, taken care not to over tighten them, and re assemble the slipper layshaft assembly and tight spot should be gone and gap also,if theres still a small tight spot run it gently around for 5 10 mins it will go free,:thumbsup:
mikeyscott
11-05-2010, 01:00 PM
Indeed I was about to say where in the manual does it say put that washer in.
I've used a Savox and Sanwa with no issues in the car.
PsycoChris
11-05-2010, 01:14 PM
Chris the problem with your steering is pretty a easy one remove the purple washers there not supposed to be there,
If you read the manual. It states the washers are there to Make the link parrallel and align the steering links. Thats what I read.
If not the link wont be align and will be on a slant. :thumbdown:
mikeyscott
11-05-2010, 01:19 PM
No it doesn't
Look at Page 6 carefully
PsycoChris
11-05-2010, 01:24 PM
No it doesn't
Look at Page 6 carefully
I have to find where I read it.
mikeyscott
11-05-2010, 01:26 PM
www.racing-cars.com for the manual in PDF format and then look at page 5 / 6 / 7 it doesn't mention the washer in that place.
ian h
11-05-2010, 01:32 PM
The washers are to go between the 2 ball cups on the link between servo horn and steering assembly if needed. ie used to lengthen the link if needed.
Chris Ashton
11-05-2010, 01:48 PM
I'm also experiencing the same with my sons shocks, after three rounds of racing the front shock started to leak so I took the top of the shock to refill it I noticed allot of metallic bits floating around inside, so I cleaned all the oil out and noticed the inside was marked. So I just filled back up with oil and finished the days racing, phone Schumacher on the Monday and explained what had happened and on the Tuesday a parcel with two brand new shock body’s and a set of seals, NOW THAT IS WHAT I CALL SERVICE. As with all new products there will be teething problems so just be patient. Real car manufacture can’t get it right look at Toyota!!!
Anyway it’s a big thumbs up for shumacher from me:thumbsup::thumbsup::thumbsup::thumbsup:
This may be due to a bent e clip on the bottom of the piston, which then scores the bottom of the shock body on full droop. Check its super flat when you install the new bodies.
eichkay
11-05-2010, 02:31 PM
I have to find where I read it.
Its at the bottom of page 6,
step 9D --- Its saying to put the washers between the ball cups on the link and not behind the ball cup like you have done.
This is a build photo of mine... for reference
http://i235.photobucket.com/albums/ee146/eichkay/Schumacher/DSC01670.jpg
mikeyscott
11-05-2010, 02:37 PM
Yup that's it
Didn't have to do it on mine with a Sanwa or Savox servo
reelman_fishing
11-05-2010, 02:50 PM
This may be due to a bent e clip on the bottom of the piston, which then scores the bottom of the shock body on full droop. Check its super flat when you install the new bodies.
The scores are on the inside of the body were the piston go's up and down. The plating has come off. It's probably a process problem. No big issue it happens :D:D
burniburn
11-05-2010, 02:51 PM
Will get mine this week and will check if it has the same issues. Kit is from the first batch as well...
Chris Ashton
11-05-2010, 03:13 PM
The scores are on the inside of the body were the piston go's up and down. The plating has come off. It's probably a process problem on big issue it happens :D:D
It's unusual, if you could get them back for us to inspect it would be cool.
mikeyscott
11-05-2010, 03:17 PM
Changing the oil in my rears tonight, so will check them too. Also changing to Ghea pistons :)
Got the 3 and 5 hole rounded on order though
reelman_fishing
11-05-2010, 03:21 PM
It's unusual, if you could get them back for us to inspect it would be cool.
yep no problem do I mark FTAO Chris Ashton ??
TUCRACEMAN
11-05-2010, 05:56 PM
Hmm, I'll be getting mine in two days. Hope it goes well.
~D
Team No Idea
11-05-2010, 06:03 PM
Had my 1st propper look at a cougar this morning............... i dribbled...............alot!!!:drool:.
Although from the response of this thread i think ill wait a while before i purchase one.
PsycoChris
11-05-2010, 06:06 PM
Its at the bottom of page 6,
step 9D --- Its saying to put the washers between the ball cups on the link and not behind the ball cup like you have done.
This is a build photo of mine... for reference
Thats why, thank you. I knew they were used for a reason, thank you sir. I just could not think of where I saw what to use.
reelman_fishing
11-05-2010, 09:33 PM
Had my 1st propper look at a cougar this morning............... i dribbled...............alot!!!:drool:.
Although from the response of this thread i think ill wait a while before i purchase one.
DON'T wait the car is absolutely AWESOME :thumbsup::thumbsup:
moth898
12-05-2010, 12:13 AM
People are saying that the coating inside the shocks are coming off, thats not the case at all. I just finished building the kit and saw what people have been talking about. It's left over material from the plating process. In other words the shocks are dirty. All that has to be done is spray them well with car deagreaser and wip the left over residue. You can repreat the cleaning a couple of times to be sure. That should remove all the little shiny bits that make it feel rough.
That being said the suspension is super smooth thanks to those BIG BORE shocks, can't wait to get this car on the track:thumbsup:
eichkay
12-05-2010, 04:04 AM
People are saying that the coating inside the shocks are coming off, thats not the case at all. I just finished building the kit and saw what people have been talking about. It's left over material from the plating process. In other words the shocks are dirty. All that has to be done is spray them well with car deagreaser and wip the left over residue. You can repreat the cleaning a couple of times to be sure. That should remove all the little shiny bits that make it feel rough.
That being said the suspension is super smooth thanks to those BIG BORE shocks, can't wait to get this car on the track:thumbsup:
yeah there is a layer of soapy looking stuff inside and outside of the shock bores when you get them, had it with the catsx aswell.. i just gave them a good clean and polish to remove that white stuff....
ian h
12-05-2010, 02:02 PM
Gearbox troubles during testing today at my local track. 1 of the o-rings on the layshaft gear fell apart leading to the pin finding its way into the gearbox and stuffing up the 3 gears. Fair play to Schumacher, I rang them and they are sending replacement parts asap. Big thumbs up for customer service.:thumbsup:
moth898
12-05-2010, 03:19 PM
yeah there is a layer of soapy looking stuff inside and outside of the shock bores when you get them, had it with the catsx aswell.. i just gave them a good clean and polish to remove that white stuff....
Thats right, what you call soap is actually the residue from the anodizing. It contains little pieces of hardened metal that act like mini razor blades that score the shock wall and rip the seals. Washing the shocks well will solve the problem.
Over the last few months i have ordered parts from schumy and notice i was over charged due to a miss keyed part number even thou i got the correct part.
I called them yesterday to make another order and today got the parts and a was credited with the error :thumbsup:
I also had a drive shaft problem and spoke to Robin on monday, he was a very helpful man in regards the replacement of the faulty part and the advise on the other two small problems which i have suffered.
All in all i`m well chuffed with the SV and is now adding my slymodz to it. First the slim line topdeck, then a mod to the reduced gap gear box to aid weather and dust, and then the rear bumper.:thumbsup:
jeffrey
13-05-2010, 09:15 PM
i have try my cougar for the first day today.
i like it alot, much better than my xxx-cr.
the only bad thing i have found are the turnbuckles. they break verry easy.
ian h
13-05-2010, 10:26 PM
i have try my cougar for the first day today.
i like it alot, much better than my xxx-cr.
the only bad thing i have found are the turnbuckles. they break verry easy.
Change them for titanium ones, Problem solved!
mikeyscott
13-05-2010, 10:28 PM
Yup got my titanium ones today. Haven't bent kit ones yet, but will swap them over for the weekend.
eichkay
15-05-2010, 09:00 AM
Had one of the Universal drive shaft let go on my first run, car had about 12mins on it when the pin flew out onto the track somewhere.. never to been seen again. i ended up sticking a spare catsx front on the car to keep me going.. it was a smidge longer but wasnt binding or touching anything..
http://i235.photobucket.com/albums/ee146/eichkay/Schumacher/drive-shaft.jpg
mikeyscott
15-05-2010, 09:04 AM
I think a few people have had this
fastinfastout
15-05-2010, 11:55 AM
finished building the car last night and had my first run today, although not very successful:blush:
3 laps in, and my ball diff slipped really bad. Funny as it let go all of a sudden, not a slowly slip. I was sure to tighten up the grub screw, but it had loosen itself. So I'm new to schumacher ball diffs. So if the grub screw loosens, then the ball diff will undo itself? I thought the ball diff was under tension from the disc spring. So everytime I want to make an adjustment to the ball diff, do I need to make adjustments to the grub screw too? Sounds like an overly complicated system:thumbdown:
So I tightened the diff up, and then one of the screws came off the the bellcrank. Didnt care too much about the screw, but had lost the post and bearing. Lucky I had another kit, as this will be used for spares. Not schumachers fault for this, I rushed the build and didnt apply threadlock where I would usually, even though the manual does not indicate to use it.
Anyway, my initial thoughts were that the car has heaps of steering and jumped really well and handled the bumps very well. Going to dial out some steering tomorrow during the heats/races.
I also had a notchy gearbox, however it didnt seem to affect the performance even though it doesnt roll freely compared to other cars.
PS, not a fan of the wing attachment, need to hold with part under the wing with pliers, otherwise it will keep on spinning and wont tighten up.
kwiksi
15-05-2010, 12:51 PM
Well I'm home and not at the track today. Barely got a full pack in.
My diff loosened up.:o Will rebuild and add some threadlock to the diff halve where screw goes in.
My steering alum pivot loosened up and flew off somewhere on the track.I could of sworn I had thread lock on these.:mad:
Ruined my weekend. Figures this would be the only spare I dont have in my box.:mad:
Buggy felt very neutral on the loose dirt. Jumped really well. Ran JConcepts groovys and Goosebumps. Gonna go through the car this week and double check all screws that make contact with metal.
The car does seem to have less droop than others when using kit settings for shock length. I went -2 turns front and rear for more droop before I hit the track.
neiloliver
15-05-2010, 04:31 PM
The car does seem to have less droop than others when using kit settings for shock length. I went -2 turns front and rear for more droop before I hit the track.
You can swap out the ball ends for longer ones and this will increase to droop. Dave Church swapped mine out last week before I had even turned a wheel on the track.
.. I have also had issues with metal in the shocks (it looked like I had filled them with glitter) and very soft track rods... Gear box is not too bad and my slipper and drive shafts seem OK so far after two meetings.
mikeyscott
15-05-2010, 05:11 PM
What ball cup lengths are you using?
neiloliver
15-05-2010, 06:14 PM
Their overall length is ~19.0mm. I dont know their part number but assume they are off the CAT SX?
DC might know.
Neil
David Church
15-05-2010, 06:37 PM
Long ball cups unscrewd 2 turns. Mega droop hehe
mikeyscott
15-05-2010, 06:38 PM
Bloody he'll that's a lot. What about driveshaft risk?
David Church
15-05-2010, 06:41 PM
Bloody he'll that's a lot. What about driveshaft risk?
No problem there, but just make sure before you run it
No problem there, but just make sure before you run it
Or use cat sx rear driveshafts, there 2mm longer.
David Church
15-05-2010, 07:09 PM
Or use cat sx rear driveshafts, there 2mm longer.
;););)
mikeyscott
15-05-2010, 07:12 PM
Ooo got a few pairs of them. Digging out so ballcups I have on the SX that are 17mm
eichkay
16-05-2010, 10:38 AM
Or use cat sx rear driveshafts, there 2mm longer.
Cat SX front drive shafts are about 2mm longer.. the Catsx Rears are much longer than 2mm ... thy wouldnt even fit i rekon.. i grabbed the drive shafts out of my parts box to check lengths when my cougars shaft feel apart on me.
Thomas B
18-05-2010, 07:20 PM
Does anybody have problem with the sero horn? Mine pulled lose from the servo today. The plastik got rounded inside and is not fixed on the servo. Is this the result of no servo saver?
Cut a corner to mutch and hit a gocart tire.
simoncrabb
18-05-2010, 07:23 PM
Yep, no saver. I stripped a servo gear on Sunday, all fixed now, but something's gotta give when you run em solid.
SteveB
18-05-2010, 07:28 PM
Yep, no saver. I stripped a servo gear on Sunday, all fixed now, but something's gotta give when you run em solid.
I thought the soft as cheese turnbuckles solved the servo saver issue:lol:
bigred5765
18-05-2010, 07:42 PM
its only the front top link turnbuckles that are a issue the others are fine,i think its because of the ofset ballcup,
TUCRACEMAN
19-05-2010, 08:53 AM
I find having no servo saver odd... Guess I got to get one hell of a servo for this car.
~D
ian h
19-05-2010, 09:01 AM
I find having no servo saver odd... Guess I got to get one hell of a servo for this car.
~D
I'm using a savox 1258. Robust and good value.
bigred5765
19-05-2010, 09:26 AM
any decent all metal geared servo will do, savox is a dam good one,
mikeyscott
19-05-2010, 10:11 AM
any decent all metal geared servo will do, savox is a dam good one,
Yup Sanwa and Savox 1258 for me :)
MattW
19-05-2010, 11:16 AM
I think virtually everyone that I know with B4/X6 glues the servo saver together, so it may as well not be there.
TUCRACEMAN
19-05-2010, 02:59 PM
I'm using a savox 1258. Robust and good value.
I wound up getting a Futaba S9551. Thank you for the suggestions, I'll have to try them out in the future.
~D
tommychev
21-05-2010, 06:28 PM
Hi Everyone
Im all the way in Australia, and have just driven my Cougar for the first time and have had some very annoying issues.
Firstly, the drive pin that one of the transfer gears is mounted on continually snapped. I replaced it 3 times and it snapped under brakes each time. I drive on high grip carpet. Im going to have to try spring steel for a pin substitute or get one made out of billet steel.
Secondly, one of my driveshafts fell apart. So i USED A PAIR OF B44 SHAFTS which is not a good thing, i'd rather keep my Schumacher all Schumacher, not a Chinese Associated bitsa
Thirdly, The camber on the front end can't be adjusted to more than 0 degrees. I wanted to go to 2 degrees negative and the ballcups were fuly screwed in at 0 degrees. So again, i had to use ASSOCIATED links from the b44 which were shorter to allow for more negative camber
Fourth problem, the instructions should mention to Threadlock the grub screw for the BALL diff. Mine came loose and melted the diff gear where the balls go in a split second. The manual shoild also state that the side with the grub screw should be on the spur gear side to avoid having the diff come lose.
Finally, notchiness in the gearbox at a certain point is also present, which was mentioned by others in the other threads.
I'll have to contact Schumacher, but being all the way in Australia is going to be a pain for replacement parts.
But overall., i love the car and it handles supreme. And i love how it isn't built in China but rather nicely built in the U.K. About times something isnt chinese. Thats why I gave up on the B4. :)
fastinfastout
22-05-2010, 01:06 AM
but dont most cars have the adjustment screw on the right when looking from the rear, regardless of position of spur?
bigred5765
22-05-2010, 08:36 AM
doesn't matter which side it goes on thats what the grub screw is for to stop it undoing,
But overall., i love the car and it handles supreme. And i love how it isn't built in China but rather nicely built in the U.K. About times something isnt chinese. Thats why I gave up on the B4. :)
Are you SURE of what you're stating here?
tommychev
23-05-2010, 06:40 PM
Are you SURE of what you're stating here?
Well, I hope im right, i was under the impression that Schumacher came back to build in the U.K. But if i'm wrong, that explains all the ridiculous quality issues ive been having with this expensive kit.
Now the coating on the inside of the shocks is flacking away. I cleaned them before assembly to the point where you could eat off them. I've done a couple of test runs, and after all the runs, i've checked the shocks only to find metallic particles floating in the silicone oil. You can even see where the coating is coming off inside.
If i knew the quality was this crap, I may not have bought this car.
slow bob
23-05-2010, 06:54 PM
If you havent already glued the pins that are held by the o rings then i would do it now as they will fall out its only a matter of time :mad:
bigred5765
23-05-2010, 07:09 PM
ares is way past 7 meetings old and still perfect, come to think of so is most of the teams??? i have fixed 3 now and all have been builders errors in one way or another including the one i did today at southlakes
phil c
23-05-2010, 08:33 PM
Hi carl , I was at south lakes today ( thanks for the set up tips ) I havejust checked the car over and have found one of the dog bone pins were it goes in the diff , is hanging out and hascut into the rear wishbone . Has anyone else had this yet???
Albertini
23-05-2010, 08:51 PM
Hi Bigred, please I mean no disrespect but I can and I'm sure most on here are fully capable of stretching an o-ring over a lip into a groove.
Granted the diff may be a skill we will all aquire but I'm pretty sure its not my (or other owners) fault that the gears are notchy and seem to be slowly eating themselves, driveshafts falling apart, orings that don't hold a pin in and gearbox halves that don't fit together.
I will though reluctantly accept that it is my fault that my steering linkage fell apart through lack of threadlock.:woot:
bigred5765
23-05-2010, 09:05 PM
Hi carl , I was at south lakes today ( thanks for the set up tips ) I havejust checked the car over and have found one of the dog bone pins were it goes in the diff , is hanging out and hascut into the rear wishbone . Has anyone else had this yet???
there has been a few i have heard of on here,contact schuy for a replacement
Hi Bigred, please I mean no disrespect but I can and I'm sure most on here are fully capable of stretching an o-ring over a lip into a groove.
Granted the diff may be a skill we will all aquire but I'm pretty sure its not my (or other owners) fault that the gears are notchy and seem to be slowly eating themselves, driveshafts falling apart, orings that don't hold a pin in and gearbox halves that don't fit together.
I will though reluctantly accept that it is my fault that my steering linkage fell apart through lack of threadlock.:woot:
not say you cant put a oring on, but theres othere factors as i discovered today like diff lube all over the oring from the diff, pins not being pressed in flush so the oring sits up on it,
Albertini
23-05-2010, 09:24 PM
This is what mine looked like after a couple of runs, the rubber oring is all but worn through, and I think the black dust over the gears is from the rubber.
The metal gears have odd marks on the teeth aswell as if they are not meshing cleanly. I've just ordered some orings and I'll give it a go at the weekend:)(after this time glueing the pins in).:)
http://i46.photobucket.com/albums/f134/wanadoochris/b4%20pics/Picture003.jpg
looking into getting a cougar when i can, these orings, are the orings from step 19 (in the manual) or step 26b?
and is a bit of thread lock fixing it, last thing id want is the gearbox in bits :)
Thomas B
24-05-2010, 10:44 AM
Wanted!
A servosaver that fits Cougar.
Broke my second servohorn today.
bigred5765
24-05-2010, 10:48 AM
impossible youll never get one to fit,and theres really no need 90% of b4 drivers super glue the servo saver up,if ur hitting stuff something has to break and better the horn than your servo,
slow bob
24-05-2010, 10:49 AM
ares is way past 7 meetings old and still perfect, come to think of so is most of the teams??? i have fixed 3 now and all have been builders errors in one way or another including the one i did today at southlakes
Hi i had the same opinion as you and had run the car 8 or 9 times with no problems
just a warning it will happen even if it has been built to perfection its only a matter of time
Thomas B
24-05-2010, 10:58 AM
Did not hit anything today. Just a bad landing and i rolled.
True, its better whith a striped servohorn. But the spare part avaliability is not so good yet in Sweden.
bigred5765
24-05-2010, 11:08 AM
a friend broke one at the weekend and we tried to fit a metal one theres no room between the steering rack and the servo horn,the only one we could get to fit was the schuy one,
mikeyscott
24-05-2010, 11:10 AM
a friend broke one at the weekend and we tried to fit a metal one theres no room between the steering rack and the servo horn,the only one we could get to fit was the schuy one,
Is it the same horn as the Cat SX? Hope so as I hold spares of these due to running a SX and a SV
Thomas B
24-05-2010, 11:12 AM
Yes its the same.
Thanks bigred. then i just whait for the spare parts.
Tom3012
24-05-2010, 11:14 AM
Ive got an aluminium one on mine, the kit one stripped after 3 races!
mikeyscott
24-05-2010, 11:21 AM
Ive got an aluminium one on mine, the kit one stripped after 3 races!
Only time I have broken the servo horn on the SX or SV was at Petit when I met the wall on the table top.. I was expecting more damage on the SX, but it held together very very well
I'm running Sanwa and Savox servos (Got a Savox 1258 to potentially go in the SV, however the Sanwa is 20g heavier).
Thomas B
24-05-2010, 11:23 AM
Ive got an aluminium one on mine, the kit one stripped after 3 races!
Witch one du you have? Link?
Albertini
24-05-2010, 11:54 AM
looking into getting a cougar when i can, these orings, are the orings from step 19 (in the manual) or step 26b?
and is a bit of thread lock fixing it, last thing id want is the gearbox in bits :)
Step 19 and I'll let you know in a couple of weeks.
make the pins shorter and stick gnub screws in there :P
ulrich
24-05-2010, 02:32 PM
Witch one du you have? Link?
We are using the Ansmann alloy servohorn (I mean Robitronic sell the same horn). I have cutting one hole off with a dremel.. see photo
bigred5765
24-05-2010, 04:18 PM
We are using the Ansmann alloy servohorn (I mean Robitronic sell the same horn). I have cutting one hole off with a dremel.. see photo
hmmm very interesting??
with the steering stright does it not touch the back of the steering rack??
chatts#725
24-05-2010, 05:44 PM
I see in the show us your cougars thread that raul garcia has a purple anodised servo horn on his looks like a core one, but i tried one and deffo doesnt fit, would have put in a link to show you all but dont know how sorry. :thumbsup:
ulrich
24-05-2010, 06:54 PM
hmmm very interesting??
with the steering stright does it not touch the back of the steering rack??
nope.. it dosen´t touch chassis.. it is a Savox 1251 servo and with no use of spacers.
MattW
24-05-2010, 07:03 PM
It could easily be that with some servos it will fit and with some it won't. Servos are very different these days - the distance from the end of the output spline to the mounting tabs can vary by a massive amount.
I've run the kit plastic one. In fairness I did break a gear in a servo however, but it is a fairly old servo and can't remember the last time it came apart - if at all!!
enfieldbanana
24-05-2010, 07:46 PM
Evening people,
I've just started to build my SV and to honest I am shocked by the quality of some of the injection moulding parts. The gearbox housing is terrible!!!!! I've never seen two halves of something go together so bad. Plus some of the anodizing is of a very poor quality. There's a part of me that is wishing I never bought this kit. You don't expect such poor parts from a PRO kits. Why did I leave Associated??? And I haven't even got half way through the build. In fact the quality of finish of the parts on the Fireblade Evo were better than what I'm coming across with the SV.
Andy
enfieldbanana
24-05-2010, 08:07 PM
Also can I add ..... the invisible window marks for the shell!!!!
Why aren't any supplied????
Andy
mikeyscott
24-05-2010, 08:35 PM
Give Schumacher a call tomorrow and have a chat with tech support etc.
Thomas B
26-05-2010, 08:05 PM
Tested to fit a Kimbrough mid size servo saver but i could not fit the top bulkhead. It was to big.
Raul Garcia
27-05-2010, 05:00 AM
I see in the show us your cougars thread that raul garcia has a purple anodised servo horn on his looks like a core one, but i tried one and deffo doesnt fit, would have put in a link to show you all but dont know how sorry. :thumbsup:
Yes it is a Core horn, and it works flawlessly.
mudflap74
29-05-2010, 12:58 PM
Argg only got to Step 7 and I am missing parts. 2 screws and a steering post. Of course Shumacher was closed when I called. So I emailed them. I hope they are fast on sending the parts :(
neiloliver
29-05-2010, 12:59 PM
I wonder if one of these will fit:
http://www.apexmodels.com/gbu0-prodshow/ANSSH0025-B.html
Neil
burgie
29-05-2010, 03:22 PM
A small kimborough servo saver will fit without problem, I reckon.
http://mediacdn.shopatron.com/media/mfg/745/product_image/895798ff804653d52ef4e572c9b859b3.jpg?1263285801
mikeyscott
07-06-2010, 10:18 PM
How much slop have people got in the steering after a few weeks racing?
slow bob
07-06-2010, 10:34 PM
There is verry little slop in the steering as long as you keep everything tight or use thread lock when you put the steering together
mikeyscott
07-06-2010, 10:36 PM
There is verry little slop in the steering as long as you keep everything tight or use thread lock when you put the steering together
Mmm, must be my car then.. Finding slop in the radius arms plastic.. Time to order some new ones then
bender
08-06-2010, 07:18 AM
Mmm, must be my car then.. Finding slop in the radius arms plastic.. Time to order some new ones then
The steering arms on my car are sloppy before the car has even been run :o
The bearings fit very poorly into the steering arms, which allows a lot of up and down movement - will be interesting to see what its like after a few meetings.
I'm not sure what material Schumacher have used for the plastic parts but it would appear that it is certainly different from what they used on the Cat SX as my Cat plastic parts were of very good quality, whereas the Cougars are frankly very disappointing.
Hopefully the on-track performance makes up for this ;)
mikeyscott
08-06-2010, 08:08 AM
Hi,
I may not bother ordering any replacements if some people have the issue from new. I'll wait a few months for them to get on top of things.
Car is awesome on the track though and love it. Agree it's not up to the same quality as the Cat SX, which is superb.
fastinfastout
08-06-2010, 01:46 PM
The steering arms on my car are sloppy before the car has even been run :o
The bearings fit very poorly into the steering arms, which allows a lot of up and down movement - will be interesting to see what its like after a few meetings.
I'm not sure what material Schumacher have used for the plastic parts but it would appear that it is certainly different from what they used on the Cat SX as my Cat plastic parts were of very good quality, whereas the Cougars are frankly very disappointing.
Hopefully the on-track performance makes up for this ;)
+1
poor fit, as I said befofre, this cougar was designed by trainee engineers:o
mikeyscott
08-06-2010, 01:52 PM
+1
poor fit, as I said befofre, this cougar was designed by trainee engineers:o
It TQ the national and finished 2nd overall, so it's not that bad..
Change to a b4 then?
Cockerill
08-06-2010, 05:24 PM
It TQ the national and finished 2nd overall, so it's not that bad..
Change to a b4 then?
Along with TQ & Win at the BRCA Winter Champs, and TQ & Win at RHR National ;)
fastinfastout
08-06-2010, 05:47 PM
I notice half the A main are filled by cougar drivers.
what were they driving last year?
and how did they do last year?
with all due respect, these drivers can do the bis with either xfactory, kyosho, AE, losi, tamiya or schu.
Cockerill
08-06-2010, 05:52 PM
and how did they do last year?.
Personally, last year I finished 11th overall, this year I'm leading the championship...
bigred5765
08-06-2010, 05:54 PM
I notice half the A main are filled by cougar drivers.
what were they driving last year?
and how did they do last year?
with all due respect, these drivers can do the bis with either xfactory, kyosho, AE, losi, tamiya or schu.
yeah probably,
and all plastic cars start there life with some small issues that usually get blown out of proportion,
Thomas B
08-06-2010, 07:55 PM
Why is it taking so long time to get spare parts in stock? The dealers in Sweden has to pic parts from the kits so people can go to races.
mikeyscott
08-06-2010, 07:59 PM
Why is it taking so long time to get spare parts in stock? The dealers in Sweden has to pic parts from the kits so people can go to races.
All in stock in the UK so a dealer issue?
Thomas B
08-06-2010, 08:04 PM
Don´t belive that all dealers i the country has problems. No one get the parts that they have orderd.
snige
08-06-2010, 08:45 PM
hey lads are people having the same problems with the s1 build as the pro version i.e gearbox problems etc
Thomas B
08-06-2010, 09:14 PM
All in stock in the UK so a dealer issue?
Are there any good dealers in UK that deliver fast too other coutries?
Rossmods ship world wide.
Darren Boyle
08-06-2010, 11:14 PM
Personally, last year I finished 11th overall, this year I'm leading the championship... Robin Hood and your annual domination meeting was earlier in the calendar though this year Tom, plus you have ditched the slow Novak stuff for faster Speed Passion gear this season mate.... :p:D;)
moth898
09-06-2010, 12:12 AM
Are there any good dealers in UK that deliver fast too other coutries?
Schumacher is actually very fast, I live in Canada and get my orders in 4 working days.
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.