PDA

View Full Version : TRF201 Build Thread....


DCM
25-06-2010, 10:56 AM
Right, after lots of waiting, anticipation, swearing at Customs and Excise... it finally arrived in ParcelForce depot, and I couldn't wait any longer, and drove to collect it a day early!!.... It came in a nice little box, with a carry handle, some bumff inside, including a flyer with a pic of Lee Martin's car. I also ordered some parts at the same time, front end bits and the Imperial front stub axles (54220). So, after a day of doing other things, on with the build.

GEARBOX

Gearbox comes in the hard graphite plastic, and it is also like the new gearbox on the Kyosho, and the motor is centralised, rather than off set to the left.

The diff now uses an alloy diff nut, but Tamiya have been clever, and the diff screw comes with threadlock on it.

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Gearbox/diff2.jpg

The diff is a normal diff (no fancy Schumacher tricks inside), but only comes with standard diff balls and not Carbide ones..... :(

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Gearbox/diff1.jpg

But once assembled, is very smooth in operation :thumbsup:

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Gearbox/diff3.jpg

The gearbox cases are pretty substantial, with lots of internal ribbing to control any flex that may go on, as the gearbox is an internal structure of the rear end, to control flex...

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Gearbox/gearbox3.jpg

And everything fits in very tidy, the only thing I could mention, the topshaft could do with a lot more shimming, as there is plenty of endlfot (about 1.5mm). Also, the layshaft gear is held on by a pin and o-ring, not being the trusting sort, I fitted the pin with loctite too...

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Gearbox/layshaft3.jpg

Once together though, the gearbox runs smooth, no tight spots at all, and it a neat little unit, as capable as anything from AE, Losi and Kyosho.

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Gearbox/gearbox5.jpg

Next step.... Rear End

DCM
25-06-2010, 11:39 AM
The back of the car will be instantly recognisable to anyone who has built a Tamiya 4wd of late. It uses the suspension balls on the inner hinge pins, with captive outer pins. Upswept rear wishbones. The only part to take care of, in building the rear, is the left rear hub goes on the right, and vice versa.

The rear suspension hold is sandwiched between the gearbox and the chassis, but it is not integral part of the T-Piece.

One little tip, if you smear a little Ceramic Grease on the screws, they thread in nice and easy on the hard graphite plastic.

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/rear%20end/rear1.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/rear%20end/rear3.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/rear%20end/rear4.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/rear%20end/rear6.jpg

One note, the rear wishbones, although similar in design (and obviously metric and not imperial), are slightly longer than the B4, as seen in the pic below (Tamiya item is the lower one).

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/rear%20end/rear5.jpg

The rear shock tower is quite a substantial item, it interlocks with the chassis, and there is a brace that goes from the tower to the gearbox. It also has mounts ready for fitting an anti-roll bar to.

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/rear%20end/rear10.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/rear%20end/rear11.jpg

Once assembled, the drivetrain is very smooth and notch free, the suspension has no binding in it either, and like all Tamiya cars, you can buy shims for the suspension arms when they become a little worn.

More to follow....

makinwaves
25-06-2010, 11:59 AM
What flavour are the wishbones? 501X, 511 high traction or the old DB-01 version?

Nice build thread, making me sorely tempted...:drool:

DaveG28
25-06-2010, 12:14 PM
High traction!

Didn't think of shimming the end float away, am I asking for trouble?? I never usually bother on this style of gearbox to be honest!?

Lee Martin
25-06-2010, 01:08 PM
i dont shim it....dont worry pig hands

DCM
25-06-2010, 01:15 PM
seriously top shelf kit guys, I do like that important parts are screwed and key located too. And I haven't had to dremmel, modify or wonder WTF is going on.....

Front end is on, very cool, steering assembly can be removed with one screw by the looks.

B44&501xRacerEX
25-06-2010, 01:35 PM
Nice! Goes together rather easy. the grease on the screws is a great tip!:thumbsup:
Tell you one thing if the diff balls are the same size as my 501x diff balls then I have carbide balls already. :)
I have 10 new carbide diff balls in the package. So if it uses 12 then I dunno...:(
I dont think you can mix and match different diff balls as that would cause problems...
Now that I think about it those diff balls are smaller, so they wouldnt work..nm

fastinfastout
25-06-2010, 03:38 PM
201x are 3/32
501 are 3mm

mikeyscott
25-06-2010, 04:22 PM
201x are 3/32
501 are 3mm

Same as AE and Losi, easily avialable

fastinfastout
25-06-2010, 04:28 PM
The only part to take care of, in building the rear, is the left rear hub goes on the right, and vice versa.
I wonder what the kit rear toe in is, and also what the toe in is if the hubs are reversed.

fastinfastout
25-06-2010, 04:31 PM
Same as AE and Losi, easily avialable
yep, 3/32 are way more common than 3mm balls.

I dont know why schumacher has odd balls, 2.4mm if I remember correctly. They also dont help themselves out by not using B4 style spurs. Anyway, enough schu talk, I'm over my cougar for the time being. This TRF has got my full attention. :thumbsup:

DaveG28
25-06-2010, 04:49 PM
I wonder what the kit rear toe in is, and also what the toe in is if the hubs are reversed.

Pretty sure the hubs are toe neutral, and the inner hinge pin mounts are 3 degree. I think they run reversed on this, and the 511 actually, just to get the ball stud in the right position to angle the upper link!

Ali hubs with 0.5 and 1.0 toe are due out in July!

mikeyscott
25-06-2010, 04:52 PM
yep, 3/32 are way more common than 3mm balls.

I dont know why schumacher has odd balls, 2.4mm if I remember correctly. They also dont help themselves out by not using B4 style spurs. Anyway, enough schu talk, I'm over my cougar for the time being. This TRF has got my full attention. :thumbsup:

2.5mm diff balls and RW Spurs for the Schumacher stuff :)

I will have a look at a TRF201 we have coming to TORCH this weekend

DCM
25-06-2010, 08:10 PM
This is a standard bellcrank affair, made of the same material as the chassis, fully ballraced with the opportunity for moving the inner ball stud position. Tamiya have opted to provide an adjustable servo saver, some may wish to glue this up, me, I am keeping it as a servo saver, as I would prefer not to strip servo horns, etc.

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/steering/IMG_1130.jpg

Once the assembly is made, you have to attach the bottom mount to the chassis, never seen this before, and to be honest, I like it :thumbsup:

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/steering/IMG_1131.jpg

you then place the steering assembly on on, then the top plate goes on, looking at it, you should be able to pull the steering assembly out without having to dismantle the front end, good forward thinking from the Tamiya guys!

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/steering/IMG_1132.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/steering/IMG_1133.jpg

DCM
25-06-2010, 08:31 PM
Nothing radical in this front end, although all the parts are keyed to each other for a positive fixing of the front bulkhead. Quality of the parts are ace as usual, although, curiously, you have to fit a small plastic spacer inside the steering arm, to space out the stub axle. Currently I have fitted the metric axle, although it is only one screw to change it to the imperial ones.

The caster blocks are also normal, run of the mill blocks, they look to be 30' too, made of the same material as the chassis and all the other 'stressed' parts.

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Front%20End/IMG_1134.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Front%20End/IMG_1135.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Front%20End/IMG_1136.jpg

The front wishbones are nice and beefy, and in comparison to the B4 items, there is not much difference to them, to be fair... :lol:

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Front%20End/IMG_1137.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Front%20End/IMG_1138.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Front%20End/IMG_1139.jpg

The wishbones are retained with captive pins, and there is also an alloy front brace to, which looks like it won't eat the little pips like on the B4.

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Front%20End/IMG_1140.jpg

And the last item is the front tower and upper plate, from the pics, I thought this would be a little flimsy, but in reality it is quite substantial.

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/Front%20End/IMG_1141.jpg

DCM
25-06-2010, 08:41 PM
These are the new HL shocks from Tamiya, with a lower shock seal cartridge, threaded adjustment, Nitride shock shafts with pistons of 1.3mm front and 1.4mm rear. The quality is ace, the less can be said about the o-rings, and as soon as Nortech can, some tasty whitties will be going in there!!

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/shocks/IMG_1142.jpg

Did anyone get tapered pistons in there's??

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/shocks/IMG_1143.jpg

Assembly is pretty simple (as long as you read the manual... :lol:), I always grease the shock shafts before putting them through the o-rings. I followed the manual, filled, pumped, full to 1mm below the top, cap on, sorted easy. Kit comes with Red rear springs and new black front springs.

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/shocks/IMG_1144.jpg

DCM
25-06-2010, 08:52 PM
Got to admit, easy car to build, no need to fiddle, although I will pull the rear wishbones back off, as there is a bit of play on the inner hinge pins, and it does need shimming, but otherwise, really nice.

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/IMG_1148.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/IMG_1145.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/IMG_1146.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/IMG_1147.jpg

T4miy4 Guy
25-06-2010, 09:44 PM
Great build thread DCM thanksfor posting it up :thumbsup:

Now get that Tamiya off the bin, have you no respect :p

Andy

coolcars782
25-06-2010, 09:50 PM
Now get that Tamiya off the bin, have you no respect :p


That's where it belongs isn't it :lol::lol:

Great build thread DCM, Looks great to :thumbsup::thumbsup:

Carl

DCM
25-06-2010, 10:07 PM
Once it goes on the track, it will be shown no respect lol

B44&501xRacerEX
26-06-2010, 12:06 AM
:woot: Wow! now to get it dirty:lol:

fastinfastout
26-06-2010, 02:34 AM
are you serious on the tapered pistons, or is that a mod you did?

Pablo668
26-06-2010, 03:24 AM
Awesome thread, the car looks great. I reall want one, but I don't need any more chassis for now.

Also, you should remember,

YOUR BLACK BIN IS FOR WASTE THAT CANNOT BE RECYLED!!!!

DCM
26-06-2010, 08:04 AM
are you serious on the tapered pistons, or is that a mod you did?

lol, it is a mod, and it is very VERY easy to do...

simoncrabb
26-06-2010, 08:58 AM
lol, it is a mod, and it is very VERY easy to do...

Go on, give us a clue, how?

DCM
26-06-2010, 10:53 AM
right, you clamp the piston on an M3 screw, with a nut. Whack it in a drill, then using a knife, spin the drill up, and hold the knife at the angle you want and the material just comes away, they are only either Delrin or Nylon. once you have cut the desired shape, clean up any burrs whilst still in the drill, with some smooth emery cloth, then deburr the holes....

Free tapered pistons!!

sparrow.2
26-06-2010, 12:48 PM
Nice build pics! Looks a quality car!

Do you know how thick the inner and outer hinge pins on the front wishbones are?

Do the slipper pads fit B4 spurs or does the entire spur gear with pads fit a B4?

Last but not least does the front end have 25° or 30° kick up (not caster on the hubs)

DCM
26-06-2010, 01:08 PM
I am thinking it has less rake on the front (25' poosibly).

B4 spur and pads would fit on. All the hinge pins are TRF tourer ones, outer are 2.6mm inner are 3mm

Fila1223
26-06-2010, 04:56 PM
trf get a 27,5

Rich D
26-06-2010, 05:02 PM
Good thread Steve - thanks for sharing and the tips. :thumbsup:

Mine still hasnt arrived as yet as i ordered all the extra alloy bits that arent due out until July at the same time :cry:

B44&501xRacerEX
26-06-2010, 06:08 PM
I feel your pain taking a bit for mine to come in as well.:blush:
Im hoping mon or tues next week.

bigred5765
27-06-2010, 09:05 PM
right, you clamp the piston on an M3 screw, with a nut. Whack it in a drill, then using a knife, spin the drill up, and hold the knife at the angle you want and the material just comes away, they are only either Delrin or Nylon. once you have cut the desired shape, clean up any burrs whilst still in the drill, with some smooth emery cloth, then deburr the holes....

Free tapered pistons!!

hi this is matty wouldnt the pistons act different between each other as u dont know if they all have the same degree of taper ?

DCM
27-06-2010, 11:06 PM
there would be a minute difference, but to be honest, not noticeable, but if you fancy trying them, but don't want to stump up the cash, worth a punt (plus being a trained engineer, my hand skills are pretty good, and got a genuine engineers eye... and he isn't having it back!!)

fastinfastout
28-06-2010, 04:02 AM
your an engineer, then you should have done it on an engineering tool, aka lathe:drool:

DCM
28-06-2010, 06:02 AM
oh, I so wish I had one of them... and a milling machine.....

super gripper
28-06-2010, 02:29 PM
I built mine this Saturday after some quick shipping from stellamodels.

http://www.tamiyaclub.com/showroom_model.asp?cid=100628&id=16126

I raced it yesterday at Titchfield Off Road Club Hants (TORCH)

http://www.torchracing.org.uk/index.php

With the right tyres and a few tweeks the car flew around the track :thumbsup:

The top boys were doing 13 laps, I was doing 12's so not bad for the cars first outing.

mikeyscott
28-06-2010, 02:34 PM
I built mine this Saturday after some quick shipping from stellamodels.

http://www.tamiyaclub.com/showroom_model.asp?cid=100628&id=16126

I raced it yesterday at Titchfield Off Road Club Hants (TORCH)

http://www.torchracing.org.uk/index.php

With the right tyres and a few tweeks the car flew around the track :thumbsup:

The top boys were doing 13 laps, I was doing 12's so not bad for the cars first outing.

It went bloody well in the final :thumbsup:

Need to show my SV some love to ensure it stands a chance of being at the sharper end ;)

B44&501xRacerEX
28-06-2010, 03:33 PM
I'm gonna run AE springs on this car. It may help...
Brown Fronts, and maybe silver rears...;) 35 wt AE all 4 corners..

If that doesnt work then I'll go back to the stock springs...just a little experiment...

fastinfastout
28-06-2010, 04:36 PM
run the car first will ya:woot:

B44&501xRacerEX
29-06-2010, 12:06 PM
OK fine I'll run it stock...it should be perfect..:thumbsup:

DCM
30-06-2010, 10:21 AM
http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/trf201-4.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/trf201-2.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/trf201-3.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/trf201-1.jpg

Fredrik Emilsson
30-06-2010, 11:13 AM
Nice touch with the stars on the wing!

But please replace those 5mm ball studs on the caster blocks. They will brake soon or later...You probably know already.

Use same as on rear hub. Nut + screw.

B44&501xRacerEX
30-06-2010, 11:42 AM
Nice DCM:thumbsup:

And a note on the ballstudds they will bend but not break. I have
never snapped the heads off they just bended on me.
The other studds that came with my 501x with the holes in them
are much better. I did my 501x like that and have never had
a problem with breakage.

I'll include a pic. They are used on the aluminum caster blocks. Put these on the whole car
and you'll never have a problem again. I dont know if you can buy the screws seperate or not.???
My 501x WCE came with a boatload of spare screws...

TKG26
30-06-2010, 12:52 PM
im considering going to Associated ball studs and RPM Ball cups... But the tamiya stuff is prettier.

RACEREX: Do you happen to have a tamiya part number for these ball studs you have in that picture?

DCM
30-06-2010, 12:58 PM
53969 for the inner front ball studs

43869 for the outer rear ball studs that you screw into.

Fredrik Emilsson
30-06-2010, 01:45 PM
Nice DCM:thumbsup:

And a note on the ballstudds they will bend but not break. I have
never snapped the heads off they just bended on me.
The other studds that came with my 501x with the holes in them
are much better. I did my 501x like that and have never had
a problem with breakage.

I'll include a pic. They are used on the aluminum caster blocks. Put these on the whole car
and you'll never have a problem again. I dont know if you can buy the screws seperate or not.???
My 501x WCE came with a boatload of spare screws...

Well, I broke one on first test run. Part of it was still in caster block. Had to drill it out...

Ball studs #53969 are good stuff in my opinion.
Ball studs #19804205 are crap.

On caster block I now use screw and ball nut #53869 (same as on rear hub)
On uprights and steering linkage #53969

DCM
01-07-2010, 12:36 PM
Just thought I would send some under body pics for you guys

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/trf201-5.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/trf201-6.jpg

I would like to thank Jimmy Oople-san for allowing me to do this online build thread, and hope it has whet peoples appetites for this car.

Team Tekin for the awesome (and probably the best, ay Northy!!) electronics out there at the moment.

And Chris Long for selling me two KO servo's for silly cheap money!!

If anyone would like to donate Brass parts for testing... I am open to offers :thumbsup:

Oh, and most important, if it wasn't for their support, these pics could not of come to you, yes, my Wheelie Bin

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/support.jpg

peetbee
01-07-2010, 01:05 PM
Ooh that battery brace looks sooo cheap! :cry:

DCM
01-07-2010, 01:37 PM
I knows.... might have to get a Carbon brace.....

Rebelrc
01-07-2010, 08:46 PM
How much is this car?

Fredrik Emilsson
01-07-2010, 08:56 PM
Depends where you buy it.

In Europe, why not try modellbau-seidel.de
They sell them for 229 euros. Add another 30 euros for body and wing. Rather cheap considering itīs a european store.

GRIFF55
01-07-2010, 09:16 PM
m-k-racing has them in stock too:thumbsup:

T4miy4 Guy
04-07-2010, 08:35 AM
Bargain!

http://cgi.ebay.co.uk/Tamiya-42167-1-10-TRF201-Chassis-Kit-EP-/380247187074?cmd=ViewItem&pt=Radio_Control_Parts_Accessories&hash=item58887f9e82

Andy

Astutekid
04-07-2010, 02:58 PM
Has anyone purchased anything from this people???

JustARcFan
04-07-2010, 03:28 PM
Me, several kits and spares.

Perfect service:)

Colinevan
04-07-2010, 04:33 PM
Depends where you buy it.

In Europe, why not try modellbau-seidel.de
They sell them for 229 euros. Add another 30 euros for body and wing. Rather cheap considering itīs a european store.

Hmm there based in Germany. Just out of curiosity. Do you pay import tazes or extra vat for eu purchases. I have a feeling that you dont, however id just like to clarify.

Thanks

Col.

Jan Larsen
04-07-2010, 07:49 PM
No you dont. The VAT for the particular country is already added in the price, just like UK shops. There're no import taxes in any EU countries. Lots of europeans buy their stuff from the UK due to this (and the low pound sterling).

I have bought stuff from Germany many times and you only pay for the goods and shipping, nothing extra.

DCM
05-07-2010, 08:12 PM
yummy in the mud

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/dirty2.jpg

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/built/dirty1.jpg

GRIFF55
05-07-2010, 08:16 PM
worked bloody well in the wet on ribs too:thumbsup:

Smartalec
05-07-2010, 09:34 PM
Anyone know what rate the black spring in the 201 kit is and the part number?

DCM
05-07-2010, 09:54 PM
worked bloody well in the wet on ribs too:thumbsup:

Till one wheel escaped :lol:

mof
11-07-2010, 01:55 PM
What is the main reason that the left rear hub needs to be on the right and the right hub on the left?

Is the situation the same for the optional aluminum rear hubs?

tony6187
11-07-2010, 05:28 PM
What is the main reason that the left rear hub needs to be on the right and the right hub on the left?

Is the situation the same for the optional aluminum rear hubs?

IT MOVES THE MOUNTS FOR THE CAMBER LINKS BACK WHICH HELPS THEM LINE UP.THESE PARTS ARE FROM THE 511 ORIGINALLY I THINK

tony6187
11-07-2010, 05:31 PM
IF YOU MEAN THE 0.5 HUBS NO.THE LEFT WILL GO ON THE LEFT RIGHT ON THE RIGHT I IMAGINE SINCE THEY ARE TOE IN

mof
11-07-2010, 06:43 PM
IT MOVES THE MOUNTS FOR THE CAMBER LINKS BACK WHICH HELPS THEM LINE UP.THESE PARTS ARE FROM THE 511 ORIGINALLY I THINK

If lining up the camber links is the reason, then it shouldn't matter as the links are differently on the alu hubs anyway.

501 has these hubs too, I think. Unless there is a slight difference between the 501 and 511 hubs.

mof
11-07-2010, 06:43 PM
IF YOU MEAN THE 0.5 HUBS NO.THE LEFT WILL GO ON THE LEFT RIGHT ON THE RIGHT I IMAGINE SINCE THEY ARE TOE IN

There are also 0 degree alu hubs, as far as I know...

DaveG28
11-07-2010, 07:48 PM
There are also 0 degree alu hubs, as far as I know...

Yep, so can go on either way!

Fredrik Emilsson
11-07-2010, 08:29 PM
The plastic hubs are from 501X. Same on 511 and 201.

On the 501X the hub marked "R" was on the right side. Thats why it says "R". The camber link was mounted on the back of hub.

On the 511 and the 201 the camber link is mounted in front of the hub. To clear the ballcup from the wheel you use the hub marked "R" on the left side.

They are, as mentioned above, a 0 degree hub.

The 501X alu hubs (#53962) can go on either side. Also 0 degrees.

kedal
12-12-2011, 01:16 PM
Did anyone get tapered pistons in there's??

http://i82.photobucket.com/albums/j271/DCM71/Tamiya%20TRF201/shocks/IMG_1143.jpg




What is the advantage of the tapered pistons ?

DCM
12-12-2011, 02:03 PM
For me, it allows the shock to drop faster than it raises.

kedal
12-12-2011, 06:15 PM
Ok, thanks. So, nothing very very important.

DCM
12-12-2011, 06:43 PM
Not really, I did it more to prove that you don't have to go and buy fancy tapered pistons, you can make them yourself.