PDA

View Full Version : 201 Idler Gear....


LhOrLoGeR
28-06-2010, 06:21 PM
It's the same problem of Cougar SV....? Just after 10 runs and i use the ceramic grease...:(
http://nsa15.casimages.com/img/2010/06/28/10062808141170603.png (http://www.casimages.com)

tony6187
28-06-2010, 06:47 PM
did the pin come out of the top shaft?or did the gear just wear out?

DaveG28
28-06-2010, 06:58 PM
No way is that wear, 2 teeth gone, rest look fine, I reckon the pin must have come out!?

tony6187
28-06-2010, 07:23 PM
would really like to no the reasoning behind a two piece topshaft.is it worth the problems people are having with pins coming out(refering to the couger sv aswell):confused:

LhOrLoGeR
28-06-2010, 07:24 PM
No no the pin is ok! It's a real problem if it's the same of SV :cry:

DCM
28-06-2010, 07:26 PM
that is an escaping pin from the top shaft, to of caused that problem.....

If someone is building a kit as a shelfer, could i borrow the layshaft and top gear to have a one-piece one?

Cockerill
28-06-2010, 09:26 PM
that is an escaping pin from the top shaft, to of caused that problem.....

Surely if it was the pin falling out it would affect more than two teeth?

DCM
28-06-2010, 09:28 PM
depends on how it fell, it it bounces and then lodged, no... but without seeing the rest of the gears, it is impossible to tell fully, but would find it hard to believe out of all the teeth, two would shear off from a faulty mould...

See what happens.

series_one
28-06-2010, 09:36 PM
Thats a sad sight to see.

I am the one behind the Dyna Storm evo/lighting project on tamiyaclub. When the prototype company was redesigning the slipper shaft on that they wanted to do the same as the 201 and, as I am reading above, the SV - use pin(s) to locate the gear. This was because it was too expensive to machine the shaft like the dyna storm orginal - with the little ribs all around, locating the metal gear insert.

Could be Tamiya has done the same thing here (ie. cost reasons). Pity. :thumbdown:

DaveG28
28-06-2010, 11:53 PM
No no the pin is ok! It's a real problem if it's the same of SV :cry:

Hi mate, are you the same guy mentioned on RCtech as having the idler go? If not then your not alone, one went on there too. From that breakage though I'd still say it's something hitting it, not "wear" or a mould failure, either the pin or something getting into the box somehow?

If it is the pin then it can be sorted, some jb weld or even a bit of heatshrink may do it!?

LhOrLoGeR
29-06-2010, 08:17 AM
Hi mate, are you the same guy mentioned on RCtech as having the idler go? If not then your not alone, one went on there too. From that breakage though I'd still say it's something hitting it, not "wear" or a mould failure, either the pin or something getting into the box somehow?

If it is the pin then it can be sorted, some jb weld or even a bit of heatshrink may do it!?

Isn't me on RCtech and it's the first one when i break a gear on RC car. I think it's a failure and i hope it's a last one for everybody.

This car is fabulous on french astro and grass track :thumbsup:

Next week i testing on clay (chalk) with no traction track on a race :woot:

ps: sorry for my english....

DCM
29-06-2010, 08:34 AM
was there any other damage in the gearbox?

LhOrLoGeR
29-06-2010, 08:46 AM
was there any other damage in the gearbox?

Nothing...

DCM
29-06-2010, 09:08 AM
very odd then, have to keep an eye on that!!

B44&501xRacerEX
29-06-2010, 12:12 PM
that is an escaping pin from the top shaft, to of caused that problem.....

If someone is building a kit as a shelfer, could i borrow the layshaft and top gear to have a one-piece one?


AE Black Grease should be used or a grease that is highly resistant to wear. AE black grease should prevent that from happening...
I think the grease got hot too fast and the gear melted...
It's also aparent we need to know what motor he ran to get it to
do that.:bored:

If it's not the pin coming out of the counter gear then it's that cheap grease...
I have some automotive gear grease that never wears out...that would also work. Get it at an autoparts store.

Rich D
29-06-2010, 12:52 PM
AE Black Grease should be used or a grease that is highly resistant to wear. AE black grease should prevent that from happening...
I think the grease got hot too fast and the gear melted...
It's also aparent we need to know what motor he ran to get it to
do that.:bored:

If it's not the pin coming out of the counter gear then it's that cheap grease...
I have some automotive gear grease that never wears out...that would also work. Get it at an autoparts store.


Its not wear its mechanical damage :confused:

Only two teeth are affected, the other are fine. If it was wear then all the teeth would show damage too.

Black grease ( Molybdenum diasulphide i think is what it is ) - i only use it on thrust race assemblies. Never heard of it being used for gears. :confused:

TKG26
29-06-2010, 02:35 PM
One of the guys killed an idler gear after one nite. He said it was from driving ruff and doing donuts.. I think its either a defect in the material or this though of the pin dropping out and doing damage...

I wonder if under no load full throttle(aka doing donuts or WOT in the air) if this could cause the pin to move? Ill take a look at mine as i have to rebuild my diff after 3 races now(relube mainly)

B44&501xRacerEX
29-06-2010, 05:05 PM
Its not wear its mechanical damage :confused:

Only two teeth are affected, the other are fine. If it was wear then all the teeth would show damage too.



I see :confused:

tony6187
01-07-2010, 09:55 PM
just building my 201 at the moment.have examined the idler gear and noticed at various different points the material looks weakend(its whiter than the rest of the gear material).have examined the spare idlers i have aswell and they are the same.it is mostly along the base of the tooth or at the outer edge.could this be a sign of a problem with the material(it seems alot harder than the material used by ae) thats causing the problems:confused:

tony6187
14-07-2010, 07:01 PM
anybody have any further problems with the idler gears?

DCM
14-07-2010, 07:44 PM
Right, just so you guys know, I have sent an idler gear away, to be copied by RW Racing, so you can have a machined idler gear. Tamiya only sell the gear in a pack with the diff gear.

TKG26
14-07-2010, 07:54 PM
The same car that ate an idler dnf'd last week with a gear box failure(i have not been able to confirm if it was an idler or a spur gear,once i find out for sure ill post back)

So far of the 5 cars at our track only one car has had any type of issue.. we are going into our 4 week now of racin them

TKG26
15-07-2010, 01:08 PM
Well the same car lost its 3rd ilder gear last nite, and a second care lost its first..... My self and one other driver have logged the most laps with our cars and have not seen this failure...yet.

we are at a loss as to why this is happening. i beleive a gear box case is going to be ordered to try out.

seankyew
15-07-2010, 02:01 PM
Below is a quote from Randy Caster (TRF driver from the USA) found in RCTech's forum:

"Tamiya has recognized an issue with the idler gear material, and are already working on a more durable material. Some people are having issues, some aren't, I think it has a lot to do with how much motor you are using, and making sure your diff/slipper are set correctly.

For anyone building, or rebuilding their 201 transmission, before installing the idler gear, boil it in water a couple times. This will help to soften the material and make it less brittle, and should hopefully solve the issue altogether until the new parts are available from Tamiya.

If you do happen to strip an idler gear, I would recommend replacing the diff gear and idler gear. This is basically just to be sure that none of the teeth on the diff gear are chipped or cracked and would cause another failure."

.

TKG26
15-07-2010, 02:32 PM
boiling! Wow have not hear of that since the old AE pan car days! LOL Oh and HPI with there PRO3 :) Oh well :) At least they are on top of it. Wont hold my breath about Tamiya handing out next gen gear sets to early owners though :)


FYI: At my club we run 13.5 motors. most have turbo/supercharged software in effect and the track is a hard packed small indoor track.... Everyone running the new car has years and years of race experience so slipper settings should not be the issue, but worth looking at.

Mr. Pink
16-07-2010, 09:24 AM
It might sound like blasphemy but the gears from kyosho rb5 (um509) fits in the 201.
The diff gear is identical but the idler is 26t instead of 27t.
There is an optional 26t idler in delerin (umw513)

tony6187
21-07-2010, 09:42 PM
my idler let go at the weekend:thumbdown: this was after 9 5min runs spread over 2 race days:mad:(let go during the 10th)hope tamiya sort this quickly

DCM
21-07-2010, 10:40 PM
I shall call RW tomorrow, see how well my idler gears are coming on

Pablo668
22-07-2010, 01:13 AM
It might sound like blasphemy but the gears from kyosho rb5 (um509) fits in the 201.
The diff gear is identical but the idler is 26t instead of 27t.
There is an optional 26t idler in delerin (umw513)

I thought the same thing but didn't know anything about the pitch/diameter/module ect of the Kyosho gear.
Also there's aftermarket metal Idlers for the RB5 on ebay.

TKG26
22-07-2010, 03:41 AM
WEll of the regular Tamiya racers at my local track, i'm the last man standing... My friends who's car has the most laps on it, let go tonight, on single tooth on the idler snapped off. My car knock on wood is second in total laps and im still on the original gear..

like a ticking time bomb.... My B4 sits in the padock nightly.. i have a feeling she will be rolled out soon. :)

Rich D
22-07-2010, 09:02 PM
I shall call RW tomorrow, see how well my idler gears are coming on


Any update Steve ? I emailed them last night but no reply as yet. Im holding off my build until these gears are ready :thumbsup:

TKG26
22-07-2010, 09:06 PM
One of our racers ran the Kysosho 26T idler last night. Said it meshed nicely and possibly the tranny rotates a bit more free.

DCM
22-07-2010, 09:06 PM
I tried a couple of times, but with RW he is always busy, try again in the morning

Rich D
22-07-2010, 09:25 PM
I tried a couple of times, but with RW he is always busy, try again in the morning


Ok cool - keep me posted please mate :)

DaveG28
22-07-2010, 09:34 PM
Ticking time bomb is a good way of saying it!! Has anyone tried boiling them and done decent mileage after? Also, how much grease are you all using on the gears when you build?

There's no doubt this is an issue, just wondering what can help mitigate it!?

DCM
22-07-2010, 10:12 PM
looking at it and after chatting with Dyna, if it is going to go, it will go early, otherwise it will run and run, to do with fibre alignment in the mouldning

tony6187
23-07-2010, 01:11 AM
mine went straight in no boiling and used plenty of grease.have boiled the replacement gears so will see what happens

DCM
23-07-2010, 03:10 PM
Right, have spoke to RW Racing, idler gears should be released middle to end of next week, you can buy them from

www.fusionhobbies.com

or

http://www.m-k-racing.com/

They are machined out of solid material, and the usual very high quality RW standard.

Rich D
23-07-2010, 04:18 PM
Right, have spoke to RW Racing, idler gears should be released middle to end of next week, you can buy them from

www.fusionhobbies.com (http://www.fusionhobbies.com)

or

http://www.m-k-racing.com/

They are machined out of solid material, and the usual very high quality RW standard.


Thankyou Steve ! :thumbsup:

DCM
23-07-2010, 04:24 PM
no worries, should be miles better than the kit one (which is unusual for Tamiya), plus you wont have to buy it in a pack with the diff gear.

TKG26
23-07-2010, 04:27 PM
2 of the local racers hear decided to boil there idler gears.................... They split in half when they tried to insert there bearings :thumbdown:

spud31
23-07-2010, 04:37 PM
2 of the local racers hear decided to boil there idler gears.................... They split in half when they tried to insert there bearings :thumbdown:


Best tell all the people who have bought the new FF03 chassis too, as it uses the same gearbox and internals mounted around other way.

tony6187
25-07-2010, 01:12 AM
2 of the local racers hear decided to boil there idler gears.................... They split in half when they tried to insert there bearings :thumbdown:
same here.made the mistake of boiling both of my spares,both split:( and the irish nationals are in 8 hours .long nite getting my b4 ready

LhOrLoGeR
26-07-2010, 09:44 AM
I've broken my 2nd idle gear yesterday after 3 race on clay dusty low traction track with a 9.5LRP X11 :cry:

I want to test the RB5"SP" idle gear during this summer
Kyosho 26T SP Idler Gear
[KYOUMW513]
http://nsa17.casimages.com/img/2010/07/26/mini_100726112908439316.jpg (http://www.casimages.com/img.php?i=100726112908439316.jpg)

DCM
26-07-2010, 09:55 AM
mine has now done about 80 mins running and no issue, but will still fit the RW idler.

LhOrLoGeR
26-07-2010, 09:59 AM
but will still fit the RW idler.

:thumbsup:

jasonrcb
26-07-2010, 10:19 AM
Same as mine no issues yet,yesterday was a dusty and testing track on the gearbox but still silky smooth,like dcm i will still change the idler gear to be on the safe side

TKG26
26-07-2010, 11:33 AM
I've broken my 2nd idle gear yesterday after 3 race on clay dusty low traction track with a 9.5LRP X11 :cry:

I want to test the RB5"SP" idle gear during this summer
Kyosho 26T SP Idler Gear
[KYOUMW513]
http://nsa17.casimages.com/img/2010/07/26/mini_100726112908439316.jpg (http://www.casimages.com/img.php?i=100726112908439316.jpg)



One of my buddies is currently running that gear right now. I also think the HPI blitz gear works as well.

LhOrLoGeR
26-07-2010, 12:19 PM
One of my buddies is currently running that gear right now. I also think the HPI blitz gear works as well.

No, the HPI blitz idler gear is bigger than the Tamiya because he have 28t.... same of the mad rat/xpro/etc.... :cry:

http://nsa17.casimages.com/img/2010/07/26/mini_100726021900935489.png (http://www.casimages.com/img.php?i=100726021900935489.png)

AaronR
26-07-2010, 06:05 PM
Right, have spoke to RW Racing, idler gears should be released middle to end of next week, you can buy them from

www.fusionhobbies.com (http://www.fusionhobbies.com)

or

http://www.m-k-racing.com/

They are machined out of solid material, and the usual very high quality RW standard.

Can either retailer ship to the USA (when top shafts and idler gears from RW are finished)?

DCM
26-07-2010, 06:19 PM
I should think so!

DCM
28-07-2010, 10:19 AM
Just spoke to Neil, apparently the moulded ones are 0.2mm smaller in diameter than they should be, using 48d.p. tooth profile. I shall trial fit a proper one tomorrow hopefully, and as long as it doesn't bind, a full size one will be made, if it does cause a bind, an identical one of the Tamiya will be made.

A few will be out by the weekend, then more next week.

Dyna
28-07-2010, 10:34 AM
Just spoke to Neil, apparently the moulded ones are 0.2mm smaller in diameter than they should be, using 48d.p. tooth profile. I shall trial fit a proper one tomorrow hopefully, and as long as it doesn't bind, a full size one will be made, if it does cause a bind, an identical one of the Tamiya will be made.


Steve, are you saying the new RPM ones are smaller than they should be or the Tamiya ones are smaller than they should be ?

I thought RPM were machining the new idlers not moulding, so i presume the moulded Tamiya ones are theoretically too small and RPM have made their machined ones slightly bigger which you are trying out ?

Sorry, just trying to clarify your statement ;)

DCM
28-07-2010, 10:37 AM
The Tamiya ones are 0.2mm small than they should be with the amount of teeth they have. Whether they have done this on purpose (chopped the tops of the teeth off to give more 'grime' clearance) or shrinkage, I don't know.

RW are going to send me a 'proper' size one to test fit into my gearbox, and go from there, he should in theory, be machining them on Thursday.

Fredrik Emilsson
28-07-2010, 08:19 PM
I checked my idle gear. No teeth missing, but the teeth are worn out...
Top gear has eaten it, ha ha
Diff gear looks fine though.
Replaced both of course.

DCM
28-07-2010, 09:10 PM
there will be an RW layshaft out soon to, one piece!

Rich D
28-07-2010, 09:16 PM
Yeah he replied to my email saying he was finishing the idler first then the layshaft was next. :thumbsup:

GRIFF55
28-07-2010, 09:19 PM
sounds good! will the gear be in shops as of fri then steve? or is thurs your testing date?

DCM
28-07-2010, 09:21 PM
because of the size difference, I will test fit the full size one tomorrow and report back, there may be some ready for Friday morning, either way

DaveG28
28-07-2010, 10:43 PM
sounds good! will the gear be in shops as of fri then steve? or is thurs your testing date?

Are you in the MK queue too mate?

DCM
29-07-2010, 02:20 PM
All going well, first gears should be with M-K tomorrow.

Tamiya have been sneaky, they have under sized the gears to make the gearbox more compact.

LhOrLoGeR
29-07-2010, 02:37 PM
Oh Yeah :thumbsup:

GRIFF55
29-07-2010, 07:09 PM
Good news with yours then steve? I shall be in the mk que!:thumbsup:

DCM
29-07-2010, 07:57 PM
the finished item should be in my sticky mitts tomorrow

Rich D
29-07-2010, 08:23 PM
Im on the MK list too :)

Do we know if Mr RW will doing doing spur gears in the std kit size ? :thumbsup:

DCM
29-07-2010, 09:01 PM
I believe Mark Knight has approached him about getting some done.

Rich D
29-07-2010, 09:37 PM
Brill even better :thumbsup:

MK Racing
30-07-2010, 02:55 PM
I spoke to Neil @ RW today, he is sending me 10 Idler's out in the post today, hopefully I will get them Monday, the price is £4.99 :thumbsup:

I will hopefully get them listed on the web site over the weekend.

Marc

DCM
30-07-2010, 03:38 PM
I spoke to Neil @ RW today, he is sending me 10 Idler's out in the post today, hopefully I will get them Monday, the price is £4.99 :thumbsup:

I will hopefully get them listed on the web site over the weekend.

Marc

GOOD NEWS :thumbsup:

LhOrLoGeR
30-07-2010, 04:02 PM
GOOD NEWS :thumbsup:

I would say more "VERY GOOD NEWS!!!":thumbsup:

tony6187
30-07-2010, 05:34 PM
I spoke to Neil @ RW today, he is sending me 10 Idler's out in the post today, hopefully I will get them Monday, the price is £4.99 :thumbsup:

I will hopefully get them listed on the web site over the weekend.

Marc
are mine included in that batch:)

DCM
31-07-2010, 10:20 PM
Fitted the idler gear, you will need to run your gearbox in a little, but then goes silky smooth!

ifuonlyknew
06-09-2010, 05:01 PM
Any word on the 1 piece layshaft?

DCM
06-09-2010, 05:27 PM
I shall phone him tomorrow!

ifuonlyknew
13-09-2010, 06:37 AM
I shall phone him tomorrow!

Well?

ifuonlyknew
18-09-2010, 12:36 AM
I shall phone him tomorrow!

WELL?

DCM
18-09-2010, 08:08 AM
he has been busy and not been able to get a sample made as yet :(

ifuonlyknew
06-10-2010, 03:24 PM
Any word on the 1 piece layshaft?

DCM
06-10-2010, 03:44 PM
nope

Jamie.T
19-10-2010, 08:46 AM
I spoke with Neil yesterday at RW, and ive pre-ordered 10 from him. Because of this and other peoples interest, he said he can clearly see the demand for them and hes bumped it up to the top of his priorities list.

Hopefully we should see the layshaft in the coming weeks.

ifuonlyknew
24-11-2010, 05:56 PM
Okay, it has been over a month. Any word on the one piece topshafts yet?

DCM
24-11-2010, 06:51 PM
To be honest, I haven't had the chance to ask of late, I will need to call him anyways!

msxmre
12-12-2010, 08:48 PM
Well guys does anyone have another solution to the idler problem. I destroyed an RW Idler in my 201 today, only been in the car 6 weeks. I actually got longer out of the original Tamiya Idler.
Thanks in advance.
Scotty....

knighthawk
12-12-2010, 09:25 PM
I new to this post but Tamiya have an updated idler / diff gear is this a solution ?

hopsing
12-12-2010, 09:47 PM
Tamiya Part# 54262 is the new reinforced gear set, come with new black idler gear and main diff gear.

stegger
12-12-2010, 09:57 PM
http://www.tamiyausa.com/product/item.php?product-id=54262

budgio
12-12-2010, 10:06 PM
Is this any good?
http://www.stellamodels.net/catalog/product_info.php?cPath=75_205&products_id=5075

sime46
12-12-2010, 10:11 PM
I've got the tamiya black reinforced ones in mine and so far so good. It managed ok with a 5.5 today on carpet! Seems ok.

msxmre
13-12-2010, 01:30 AM
Thanks for your help guys.
Scotty....

sim
18-12-2010, 12:39 AM
How are the new reinforced idlers holding up?

DASH
18-12-2010, 06:26 AM
two meetings at Taplow and AOK here