PDA

View Full Version : Help with wandering DB01R


carnage
20-08-2010, 09:10 AM
Hi
I thought I'd ask the experts
I've been running my db01r for 8 or so months and have had centering issues for 5 of those months
Problem in point form as it's easier for some one educated in Maggie Thatchers England
. Steering continuially needs to be "trimmed" during a run seems to bea variation of 2-3 clicks
New servo (Savox)
new radio old Hitec pro car, new radio Core rc
tried toe in
tried shimming out slop, tried leaving in slop
steering loose and free of binding
really losing confidence when runniong the car, aparft from that, I love it,
jus need to be able to go in a straight line lap after lap
look forward to your thoughts
Steve

DCM
20-08-2010, 09:20 AM
Worn servo saver splines, so the servo saver is jumping on the splines, replace it with either the Tamiya High Torque or a Kimbrough servo saver, or if you are brave, a servo arm.

mattybucks
20-08-2010, 10:55 AM
and if it's not the servo horn it's time for a new servo, or at least a set of gears.

carnage
20-08-2010, 11:41 AM
thanks for the replies but not the problem, I'm not running a servo saver and the deflection is very small compared to a whole tooth jump on the spline, runs off course by no more than 1 metre over a 10 metre run.
also brand new servo, 3rd servo I've tried
cheers Steve

Pops
20-08-2010, 11:56 AM
Maybe the ballcups jump the threads on a crash...Mine did and only small taps on rope! Some sort of tollerance issue so i changed all the ballcups and it stayes trimmed even after my big crashes:cry:

Dyna
20-08-2010, 12:00 PM
I might be barking up the wrong tree, but it couldnt be the TX/RX throwing the steering out by going 'out of tune' could it ? I know youve said youve tried a couple of diferent sets but it strikes me as a electrical problem, as you have to trim it a few clicks during runs.

All the likely mechanical suspects have been suggested and you've said you've tried them all, including i presume making sure the shocks & suspension arent binding, all suspension parts are physically ok with no hidden cracks opening during running ( i had that on a RB5 and took me a while to spot it ) and all the car settings are true, so that's the likely culprit to my mind... Id try another completely different RX & TX & then a different servo to make 100% sure.

fastinfastout
20-08-2010, 12:01 PM
it may be an issue with the tamiya ball cups.

its a common problem with tamiya and durango.

the turnbuckles 'jump' thread/s unknowingly after a hard jump etc.

its a common mod, to get hpi or AE tc5 ball studs and losi/rpm ball cups.

carnage
20-08-2010, 12:08 PM
it may be an issue with the tamiya ball cups.

its a common problem with tamiya and durango.

the turnbuckles 'jump' thread/s unknowingly after a hard jump etc.

its a common mod, to get hpi or AE tc5 ball studs and losi/rpm ball cups.
yeah, I heard that as well but surely if it jumps 1 thread it jumps them all, meaning every thread will jump 1 thread causeing a completely stripped ball cup, I've got a set of RB5 ballcups, might try them
cheers
Steve

carnage
20-08-2010, 12:14 PM
I might be barking up the wrong tree, but it couldnt be the TX/RX throwing the steering out by going 'out of tune' could it ? I know youve said youve tried a couple of diferent sets but it strikes me as a electrical problem, as you have to trim it a few clicks during runs.

All the likely mechanical suspects have been suggested and you've said you've tried them all, including i presume making sure the shocks & suspension arent binding, all suspension parts are physically ok with no hidden cracks opening during running ( i had that on a RB5 and took me a while to spot it ) and all the car settings are true, so that's the likely culprit to my mind... Id try another completely different RX & TX & then a different servo to make 100% sure.
On that note,
The deflection is proportionate to the steering curve profile on my old Hitec radio, ie
sensitive steering (around neutral) = bad fault deflection,
insensitive steering = slight fault deflection
this led me to buying a new Radio/RX combo, nowthe problem is back
What are the odds of 2 radios built 3 years apart by different manufacturers having the same fault
Steve

DaveG28
20-08-2010, 12:41 PM
Are you running the option steering arms/posts?

I had the same issues with my db01r, it was difficult to solve but the angle of the horn in neutral, and also general slop, made things worse, especially te servo horn angle, does it have matched left/right lock etc?

carnage
20-08-2010, 12:56 PM
Are you running the option steering arms/posts?

I had the same issues with my db01r, it was difficult to solve but the angle of the horn in neutral, and also general slop, made things worse, especially te servo horn angle, does it have matched left/right lock etc?
it's got the standard db01R steering,
the steering is tuned as best as I c an, EPA etc
when it's going good I'm in love with it but when it's playing up it's so frustrating
Steve

Dyna
20-08-2010, 01:03 PM
On that note,
The deflection is proportionate to the steering curve profile on my old Hitec radio, ie
sensitive steering (around neutral) = bad fault deflection,
insensitive steering = slight fault deflection
this led me to buying a new Radio/RX combo, nowthe problem is back
What are the odds of 2 radios built 3 years apart by different manufacturers having the same fault
Steve


Pretty high odds i admit, but then again you said you've tried pretty much everything else and you did ask the question in the first place....

sosidge
20-08-2010, 01:05 PM
Servo mounted firmly? The Durga is a bit under-provided in the servo mount stakes, would be easy for it to slide a little side to side in use. Try a layer of servo tape under the servo to hold it in place.

carnage
20-08-2010, 01:10 PM
Servo mounted firmly? The Durga is a bit under-provided in the servo mount stakes, would be easy for it to slide a little side to side in use. Try a layer of servo tape under the servo to hold it in place.
sounds good, I'll try that
cheers

carnage
20-08-2010, 01:17 PM
Pretty high odds i admit, but then again you said you've tried pretty much everything else and you did ask the question in the first place....
I fix electric forklifts for a job and I don't rule out that scenario if I've still got a problem after sticking the servo with double sided tape and fitting RB5 ballcups, I'll see if I can sneek a Futaba 3vcs past my missus
Thanks for your help
Steve

Pops
20-08-2010, 01:22 PM
Does it always need trimming in the same direction and by the same ammount...My ballcups only moved slightly each time and never completely stripped.. the only way i found the problem was when i tried to push a deformed front tyre back into shape and heared a click... next quali the car kept bearing the one way

carnage
20-08-2010, 01:35 PM
Does it always need trimming in the same direction and by the same ammount...My ballcups only moved slightly each time and never completely stripped.. the only way i found the problem was when i tried to push a deformed front tyre back into shape and heared a click... next quali the car kept bearing the one way
it needs trimming in both directiongs by the same amount, I have noticed a slight relationship that after I turn right it steers to the left and after steering to the right it steers to the left
thanks
Steve

peetbee
20-08-2010, 01:43 PM
I've changed my servo posts to B4 ones after a similar experience and problem went away. Like you I wasn't running a servo saver so I think the standard servo mounts would flex instead.

Pops
20-08-2010, 01:44 PM
If the steering mechanism is nice and free with the horn unpopped at all suspension levels then surely its a centreing issue with the servo?.. dont the free moving digital ones keep centering and adjusting for as long as its powered up..Think i read that somewhere:cry:

carnage
20-08-2010, 01:58 PM
plan of action,
new servo mounts,
double sided tape as well
I'm sorry but I'm going to replace the ballcups as well, I know doing this will not give a definative answer to the problem but there's a big meet next weekend.
THANKS TO EVERYONE WHO'S POSTED,I now feel confident I can fix the old girl,
please keep on posting
I'll post my findings
Steve

carnage
20-08-2010, 02:01 PM
If the steering mechanism is nice and free with the horn unpopped at all suspension levels then surely its a centreing issue with the servo?.. dont the free moving digital ones keep centering and adjusting for as long as its powered up..Think i read that somewhere:cry:
the problem happens with a free moving Savox servo and other stiff digital/nondigital servos
cheers
Steve

fastinfastout
20-08-2010, 03:40 PM
try operating the car on the stand, as sometimes it could be radio glitch. Just a suggestion. I've had it before, even on 2.4ghz, just relocated the receiver wire. But yes, do try all the things people mentioned above:thumbsup:

njc11
20-08-2010, 08:57 PM
Ive not looked through all the posts... but i recently dropped my Esprit 3 transmitter and bust the steering stick... i managed to glue it up to finish the meeting but the car felt " wondery "

Anyway spoke to Derek Bailey who supplied me the parts to fix and he said make sure you do the " adjust VR " which sets up all the neutral points otherwise if you dont the car will feel like its wondering..

Just a thought.. as it cured my cars antics.. initially i thought it was a loose servo saver!

Cheers

Nick
:thumbsup:

mole2k
20-08-2010, 09:23 PM
My 501x suffered from this until I replaced all the ball cups. They where moving when put under pressure. It didn't even have to be a full on accident, even just a light brush off an apex that doesn't unsettle the car was knocking the steering trim off.

sim
23-08-2010, 11:49 PM
If ball cups are jumping threads, you should be able to measure it with a caliper, especially if you originally followed manual-recommended lengths.

mole2k
24-08-2010, 07:57 AM
Mine didn't actually jump the threads but they did move small amounts when tapped, it was very noticeable by how much the camber could be knocked out per run without any actual crashes.

Migs
27-08-2010, 03:02 PM
Mine didn't actually jump the threads but they did move small amounts when tapped, it was very noticeable by how much the camber could be knocked out per run without any actual crashes.
no offence man, but your post doesnt make sense, if the camber changes just when the car is tapped, and the thread isnt jumping, what else is going on? even if its possible that the turnbuckle is being turned in the cups by the lateral forces on the wheels, it still means theyre rubbish

mole2k
27-08-2010, 05:38 PM
To jump the thread they would have to move a fairly large amount, I can only assume they were turning the thread. They are rubbish, I wasn't saying anything to the contrary just that mine didn't seem to change by large amounts just very small amounts.

The problem went away with all new ball cups on the car though.

carnage
27-08-2010, 07:51 PM
I have replaced all cups with Kyosho ones, stuck servo down with 3M 2.5kg doublesided tape as well as mounts
Big meet this weekend (130 entries) at my club, Hoping this will solve the issue
I'll let you all know the result
thanks everyyone for your help
Steve