View Full Version : Another Durango body
Bugle
02-02-2011, 10:25 AM
Had a go at designing my own Durango shell. Designed it to give lots of room for electronics, motor heatsinks/fans while keeping a really low roof line. Went for as much downforce as possible at the back :D
http://lh5.ggpht.com/_f_qpmXnmt0k/TUkJLqQhd0I/AAAAAAAAAN0/zk5Z2iTZUOk/body3.jpg
http://lh4.ggpht.com/_f_qpmXnmt0k/TUkJMEM-fsI/AAAAAAAAAN0/f5NB9Uo9eDw/body7.jpg
http://lh4.ggpht.com/_f_qpmXnmt0k/TUkJMCVus-I/AAAAAAAAAN0/_GOnZikCf-M/body10.jpg
http://lh6.ggpht.com/_f_qpmXnmt0k/TUkJMIkwisI/AAAAAAAAAN0/Cppx2bM4x74/body4.jpg
http://lh4.ggpht.com/_f_qpmXnmt0k/TUkJMXXFIPI/AAAAAAAAAN0/5q-l3lDKZ_o/body12.jpg
franki
02-02-2011, 10:38 AM
nice work!!
Rebelrc
02-02-2011, 10:40 AM
That looks the nuts
I love it!
Love the roofline where it goes to a point at the back
I will buy some
frobes2
02-02-2011, 11:40 AM
Yes please, I want one!!!!
Where and how much??
Scott..
stegger
02-02-2011, 12:01 PM
Very nice !! Some very good work there fella. :)
How did you make it ?
burniburn
02-02-2011, 12:08 PM
Awesome work mate! This shell looks really fantastic!
Mr. Red
02-02-2011, 12:12 PM
Bloody awesome!!! Smooooth!
Oliv996
02-02-2011, 12:16 PM
At least, a bulldogless body :)
Very nice...
Bugle
02-02-2011, 01:45 PM
Yeah I was trying to avoid the 'forward cab' look by extending it all the way to the back :)
Was going to sell them for $25 AUD for the body and wing, which seems to be about £16 or 18 euro.
Stegger it's vacformed polycarbonate, the mould took a hell of alot of dremelling and sanding though :)
JohnM
02-02-2011, 04:44 PM
That's awesome, best aftermarket body by miles:thumbsup:
Rebelrc
02-02-2011, 04:50 PM
can we have a pic from directly above please:)
steve73
02-02-2011, 05:31 PM
Unbelievable!
PHANTASTIC!:thumbsup:
3 Wishes:
1) Picture together with the Orginal Body
2) Picture without the body, to see your electronic installation
3) Your bank connection, the price and PLEASE, PLEASE send me one!
jeffrey
02-02-2011, 05:40 PM
i want one also :p
it looks ace:drool:
and more room is always better :p
Bugle
03-02-2011, 07:27 AM
Thanks for the comments :)
I've uploaded a top down pic and a few others i'd taken here https://picasaweb.google.com/piazzanero/DurangoDEX410Body
Steve73, the current electronics setup was done to suit the standard body although it's a tight fit, it's a speed passion ESC with one of those tiny hobbyking spektrum receivers.
Have a look in the link I posted above with some closeup pics of the cockpit you can sort of see how much room there is around the current stuff. I'll take some photos with a clear body when I make some more to give a better idea on clearances. Main thing which gives the room for the ESC & receiver is that the body doesn't have the step in the side of it which the original has. I'll see if I can line it up next to another durango with a standard body too at this weekends race meet.
Kusal
03-02-2011, 09:32 AM
Hi,
Please keep us informed when available and how to order?
Greetz:)
muratti
03-02-2011, 11:19 AM
Really nice body. I am very interested in buying one too! Please keep us informed! :drool:
Mike Parker
04-02-2011, 10:09 AM
Yep nice looking shell there fella :thumbsup: definately keep us informed if you intend to do a batch :)
Mike P.
Stefan Jarl
04-02-2011, 12:19 PM
My favorite is still the Tresrey Gainabull .:)
Bugle
04-02-2011, 01:45 PM
I should be making a batch of them early next week. :D
I'll donate the equivalent of ebay fees for any shells I sell on oOple, hopefully that's ok
I think Jimmy would like that, help him pay for the world's report.
jeffrey
04-02-2011, 03:40 PM
ok great let us know in this topic
RETRO R/C
07-02-2011, 10:55 AM
Hi Guys,
I used one of the "Bugle Boy" wings last year to win one of our largest 1/10th buggy races, here in Australia - the NSW State titles. The wings are extremely strong and provide great downforce. Unfortunately at the time - the Bugle Boy Body was not fully developed - although a few early "pulls" had been made by Thomas (Bugle).
I have attached a few pics of my new Bugle Boy shell - freshly painted and ready to hit the track. (Please forgive the use of rattle cans - I like simple paint jobs). I think the paint job shows off the lines of the shell. I will try and get a few pics of my radio instrallation as well if interested.
This shell leaves a TONNE of room for electronics without looking "pregnant"!! :woot::wub:thumbsup:
http://i160.photobucket.com/albums/t180/darrynsretrorc/J%20Concepts%20Clash%202011/Clipboard11.jpg
http://i160.photobucket.com/albums/t180/darrynsretrorc/J%20Concepts%20Clash%202011/Clipboard08.jpg
http://i160.photobucket.com/albums/t180/darrynsretrorc/J%20Concepts%20Clash%202011/Clipboard12.jpg
http://i160.photobucket.com/albums/t180/darrynsretrorc/J%20Concepts%20Clash%202011/Clipboard10.jpg
http://i160.photobucket.com/albums/t180/darrynsretrorc/J%20Concepts%20Clash%202011/Clipboard13.jpg
I think the price that Thomas is asking for these shells is truly excellent and he deserves a pat on the back for helping out fellow racers, I also saw and placed an order for his new DEX Undertray and front bumper.......great stuff.
Cheers
Darryn
Wow!!! This is most likely the coolest 1:10 OR shell I've ever seen! Absolutely amazing! :thumbsup:
Bugle
10-02-2011, 01:07 PM
Hey everyone, i've made a bunch of shells, $25 AUD (http://www.xe.com/) plus postage for a body and wing. PM me to sort out postage costs if you're interested.
Thanks Darryn, too bad you weren't using the bugle boy wing last weekend you would've won it :thumbsup:
This is the undertray and bumper Darryn was talking about, I posted it on here a while ago but there didn't seem to be much interest, I guess more people would be after them if they were all running atomic carbon tubs :)
https://lh3.googleusercontent.com/_f_qpmXnmt0k/TVPZahfFI9I/AAAAAAAAAPs/Wo6CXJvCVCc/undertray.jpg
Chucked a mamba max pro into the car for a test fit being the biggest ESC i've got, can fit it any which way you like really, got the receiver between the spur and the ESC here. Didn't wire it all up since i'm going to use it in another car instead.
As far as motor cooling goes, Darryn's car pictured above has 2 heat sinks on the motor, someone else was running a fan down beside the motor with holes in the side of the body to draw air in. Another had a fan and heatsink angled so that the fan was going up inside the cockpit.
Some pics with a clear body
https://lh5.googleusercontent.com/_f_qpmXnmt0k/TVPZVsKPfiI/AAAAAAAAAPc/oeZ-Mvv85Nk/clearbody2.jpg
https://lh6.googleusercontent.com/_f_qpmXnmt0k/TVPZVrRQ8pI/AAAAAAAAAPY/h3FeHtQNM1c/clearbody1.jpg
https://lh5.googleusercontent.com/_f_qpmXnmt0k/TVPioWnUF3I/AAAAAAAAAQM/I_OcOGP7g8A/clearbody6.jpg
https://lh3.googleusercontent.com/_f_qpmXnmt0k/TVPZV_WoGOI/AAAAAAAAAPk/kGDHrGVyZJc/clearbody4.jpg
https://lh3.googleusercontent.com/_f_qpmXnmt0k/TVPZm-jsSSI/AAAAAAAAAPw/vBBnhDP-SU8/electronics1.jpg
I chucked some other pics of the body next to the old original one in here aswell https://picasaweb.google.com/piazzanero/DurangoDEX410Body#
jeffrey
10-02-2011, 04:20 PM
you have a pm
:)
paulywally
10-02-2011, 06:55 PM
You have another pm
Kusal
10-02-2011, 07:12 PM
And another pm.
BostonNelson
10-02-2011, 11:58 PM
One more :)
jimmy
11-02-2011, 12:15 AM
This shell looks awesome I have to say.
Daryl
11-02-2011, 09:00 AM
Thats pretty sexual!
Bugle
11-02-2011, 10:14 AM
Thanks Jimmy and everyone :D
Also I forgot to mention, the protective film they include with this polycarbonate (Bayer brand 0.8mm thick) i'm using isn't vacuum formable. It can't take the heat so I have to remove it, therefore there is no 'overspray film' on the outside. Glad wrap works just as well anyway and is easier to peel off :)
Big G
11-02-2011, 10:16 AM
I love the original shell, but because it goes in after the pods the wires of my receiver touch the shell and push it out slightly. That's my only complaint. I had no problem really fitting my SP GT and futaba 2.4 gear in there even used the mounting plate for easy removal.
Undertray would be greatly received, although I've stopped crying now everytime I see it belly something hard and abrasive :D
This shell also gives a bit more real estate for stickers hehe
Chequered Flag Racing
11-02-2011, 11:48 AM
What name would you give to this bodyshell?
DexAero
AeroDex
410Aero
Aere410
Bugle hasn't a name for his shell so see if you can do better then mine. Have fun trying.
You never know he may pick one from this thread or just come up with his in his own good time
BostonNelson
11-02-2011, 12:14 PM
What name would you give to this bodyshell?
TD Pu**ymagnet.
Bugle
11-02-2011, 12:38 PM
What name would you give to this bodyshell?
DexAero
AeroDex
410Aero
Aere410
Bugle hasn't a name for his shell so see if you can do better then mine. Have fun trying.
You never know he may pick one from this thread or just come up with his in his own good time
Aerango?:eh?:
lol boston, gonna be fighting off the trophy girls hey
kriske
11-02-2011, 01:14 PM
What name would you give to this bodyshell?
DexAero
AeroDex
410Aero
Aere410
Bugle hasn't a name for his shell so see if you can do better then mine. Have fun trying.
You never know he may pick one from this thread or just come up with his in his own good time
bodbugle body. :thumbsup:
burniburn
11-02-2011, 07:38 PM
speedbugledeck plus ultrawing
West Ridge Racing
12-02-2011, 12:27 AM
Pure beauty. Bugle, I want to shake your hand. Really excellent work.
How thick polycarbonate did you use for this body? And does it become thinner when formed in the making?
Chequered Flag Racing
15-02-2011, 09:44 AM
What name would you give to this bodyshell?
no one been drinking there creative juices then as ideas seem to have dried up :(
Bugle Flux Evo I
Bugle Gurgle
FreeFlow
CuttingEdge
Swooosh
DownUnder
UnderDown
Sweep
Zoomer
Screamer
Ebeneezer Goode
Spock
Warp
Banzai
Kamikaze
B-Mag DeLuxe
Loose sprocket
Zocket
Moon Rocket
Pzycho
Zappa
BulldogKiller
CarForwardMustKill
Zoidberg
Zlut
KaPow
AberSchnell
2Fast4U
Über
TheNeedle
SpeedNeedle
Harakiri
Flare
Bazooka
Yezzir
YaMan
-happy now? :D
Bugle
15-02-2011, 12:34 PM
I can't make up my mind, maybe we need a poll :lol:
Thanks to everyone who's bought them. Need to make more now :thumbsup:
Bugle
15-02-2011, 12:56 PM
Oh yer another thing with mounting these bodies, which applies to any durango body really, you need to make the body mount holes slightly oversize and make sure the body has a little clearance around the front bulkhead so the body isn't taking so much load when the car flexes as they seem to flex quite alot especially the R.
Most of the guys here seem to just slice the clip knob off the rear mount just using it as a support and use velcro on the sides. Darryn has done that on his one in the pictures.
... added some more name suggestions :D
Btw! Would you mind making a similar version for the B44? Just love the basic layout of this shell!
teeforb
15-02-2011, 03:40 PM
I'm trying to send pm, but it don't look like it's going through. How much shipped to CA in USD?
Thx
Bugle
16-02-2011, 02:38 AM
Hey teeforb, got the pm fine, pm'd you back :)
... added some more name suggestions :D
Btw! Would you mind making a similar version for the B44? Just love the basic layout of this shell!
Ebeneezer Gode?:lol:
I actually cut the sides off one and test fit it to a B44, it would just need the sides made a bit wider and it would fit, it would sit a bit higher though.
slowjun
16-02-2011, 07:22 AM
did i just see an undertray included with this body? hmm.... prices please.... plus shipping to SG.
thanks.
Ebeneezer Gode?:lol:
I actually cut the sides off one and test fit it to a B44, it would just need the sides made a bit wider and it would fit, it would sit a bit higher though.
http://www.youtube.com/watch?v=oPzv_EwxMl0
-one of my all time favorite songs! Gives me another idea: Geezer! :)
Sorry, forgot an O :D
Sounds great, I'd be very interested in one for the B44!
Chequered Flag Racing
16-02-2011, 08:47 AM
Window Mask's
does the shell come with them or not?
I'm guessing the later
carnage
16-02-2011, 09:47 AM
Top shell Thomas
could you do one for a dbo1 if I give you my car to work off, all the tamiya bodyshells for the db01 look shit, Roman, Nick and myself would get 1 or 2 each or in Nicks case he'll need about a dozen.:woot::woot:
cheers
old skoolie
Bugle
16-02-2011, 09:58 AM
http://www.youtube.com/watch?v=oPzv_EwxMl0
-one of my all time favorite songs! Gives me another idea: Geezer! :)
Sorry, forgot an O :D
Sounds great, I'd be very interested in one for the B44!
haha I remember that song now :)
Window Mask's
does the shell come with them or not?
I'm guessing the later
Nah no masks currently, I don't have the gear to make them but I am looking into sourcing some though.
did i just see an undertray included with this body? hmm.... prices please.... plus shipping to SG.
thanks.
The undertray isn't included, I can include an undertray and bumper for an extra $15. SG postage would be $13.40.
Bugle
16-02-2011, 10:02 AM
Top shell Thomas
could you do one for a dbo1 if I give you my car to work off, all the tamiya bodyshells for the db01 look shit, Roman, Nick and myself would get 1 or 2 each or in Nicks case he'll need about a dozen.:woot::woot:
cheers
old skoolie
Hey Steve, yeah if you lend me a db01 I can have a go, something similar to the durango one? Doing the scoops and getting around the motor should be interesting:)
Chequered Flag Racing
16-02-2011, 10:42 AM
bumper's
what do these llike?
point us to a picture
I've never ever had good results with any window masks. Never fits 100%, and you get bleed.
What to do: Draw lines with an overhead projector pen on the outside. Use a brush (don't need to airbrush) and put on 2x thick coats of Bob Dively Liquid Mask. Cut along the pen line with a sharp Excel knife. Peel of the excess. Paint. >> Perfect :thumbsup: Not to forget you can then also make your own "custom" windows!
Chequered Flag Racing
16-02-2011, 12:05 PM
no one been drinking there creative juices then as ideas seem to have dried up :(
Rayzor
RayzorBak :thumbsup:
E-Rayzor
letter Y could be dropped in all the above
OutBak (ref Australia or with the C if needed)
Bugle
16-02-2011, 12:56 PM
I've never ever had good results with any window masks. Never fits 100%, and you get bleed.
What to do: Draw lines with an overhead projector pen on the outside. Use a brush (don't need to airbrush) and put on 2x thick coats of Bob Dively Liquid Mask. Cut along the pen line with a sharp Excel knife. Peel of the excess. Paint. >> Perfect :thumbsup: Not to forget you can then also make your own "custom" windows!
I've never had them bleed, they are a challenge to stick on in the exact right spot though..
Only problem with liquid mask + knife is if you cut into the polycarbonate you weaken it, so it might crack later.
I usually just cut thin strips of electrical tape and run it along the edge, it's easy to bend around curves
Bugle
16-02-2011, 12:59 PM
what do these llike?
point us to a picture
in this pic, it screws on through the front 2 screws and bends up around the front covering the original front bumper, it was kindof required for the undertray because the first part to break was the front after a few nose dives.
https://lh3.googleusercontent.com/_f_qpmXnmt0k/TVPZahfFI9I/AAAAAAAAAPs/Wo6CXJvCVCc/undertray.jpg
fastinfastout
17-02-2011, 07:52 AM
Thanks Bugle for the quick post:thumbsup:. Got it today, and painted already. I'm not usually creative enough with my paint jobs and use one color can jobs!
I found it a little hard to follow the original window outline as I usually lay down 2inch masking tape and then knife it away, however the body window indents are not big/deep enough to show through the masking tape(hope that makes sense). However I might try bugles way next time with the thin insulation tape way. So I created my own window design :)
Thanks Bugle for the quick post:thumbsup:. Got it today, and painted already. I'm not usually creative enough with my paint jobs and use one color can jobs!
I found it a little hard to follow the original window outline as I usually lay down 2inch masking tape and then knife it away, however the body window indents are not big/deep enough to show through the masking tape(hope that makes sense). However I might try bugles way next time with the thin insulation tape way. So I created my own window design :)
Tip: Use a pen (overhead) to draw up the outlines of the windows. Then use a lamp to see through the masking tape, then cut ;) And wipe off pen lines with alcohol afterwards.
20625
Bugle
17-02-2011, 09:35 AM
Procat spec :lol:
jeffrey
17-02-2011, 02:27 PM
Thanks Bugle for the quick post:thumbsup:. Got it today, and painted already. I'm not usually creative enough with my paint jobs and use one color can jobs!
I found it a little hard to follow the original window outline as I usually lay down 2inch masking tape and then knife it away, however the body window indents are not big/deep enough to show through the masking tape(hope that makes sense). However I might try bugles way next time with the thin insulation tape way. So I created my own window design :)
i like your window design, maybe i done my shells the same way :)
grtz jeffrey
fastinfastout
17-02-2011, 03:05 PM
I actually love the vintage yokomo's.....superdogfighter, which has a similar design to the windows, and I did something like that to my bmax.
X5 Addict
18-02-2011, 04:00 AM
Bugle Flux Evo I
Bugle Gurgle
FreeFlow
CuttingEdge
Swooosh
DownUnder
UnderDown
Sweep
Zoomer
Screamer
Ebeneezer Goode
Spock
Warp
Banzai
Kamikaze
B-Mag DeLuxe
Loose sprocket
Zocket
Moon Rocket
Pzycho
Zappa
BulldogKiller
CarForwardMustKill
Zoidberg
Zlut
KaPow
AberSchnell
2Fast4U
Über
TheNeedle
SpeedNeedle
Harakiri
Flare
Bazooka
Yezzir
YaMan
-happy now? :DToo much red cordial Shy Boy!!:thumbsup:
There is a tonne of room under the BingleBungle Body (:D) for cooling options. Best layout Ive found is to sit a 30mm fan under the front driveshaft (you need to have the 25mm battery kit fitted which raises the spur assembley slightly) and big mofo heatsink(s) on the motor (otherwise a 25mm fan fits under with plenty of room). If you use 5mm thick fans you can have it mounted on the heatsink no probs. I use 10mm thick fans and they would hit the body.:(
Front bumper is going to last a year! It's pretty heavy duty!!!:)
Rear wing sensational! But the stiff wingmounts on these DEX's keep punching through the wing!!! Is there a flexy mount to fit out there somewhere??
With using liquid mask, you have to cut them properly. As Bugle said, if you push too hard you score the plastic and it will break. Easy does it!!:cool:
I actually cut the sides off one and test fit it to a B44, it would just need the sides made a bit wider and it would fit, it would sit a bit higher though.
Could you be bothered to post a pic of that?
Cheers
jeffrey
22-02-2011, 10:04 AM
they are deliverd today
super fast:o 1 week to ship to belgium "other side of the world :p"
very nice pakaged.
bugle is a top seller.
thanx alot
if i'm done with painting i post a pic :)
grtz jeffrey
Chequered Flag Racing
22-02-2011, 10:08 AM
they are deliverd today
super fast:o 1 week to ship to belgium "other side of the world :p"
very nice pakaged.
got mine yesterday in the UK :thumbsup:
bugle is a top seller.
thanx alot
there's a trader feedback thread for Bugle ;)
Bugle
22-02-2011, 01:03 PM
Cool, faster for stuff to get there than it is to get here :thumbsup:
Could you be bothered to post a pic of that?
Cheers
I'll take a pic tomorrow, should be good for a laugh, I think it will look strange with straight and wide sides, it would give alot of downforce though.
DekelzMan
23-02-2011, 02:14 AM
Heya Bugle!
The bodies arrived today, all the way to Canada! They look simply beautiful. Can't wait to build the car and mount this Bad Boy up! I think I can do a wrap for it without too much effort. I'll post some shots when it's done.
Many Thanks again!
captainlip
23-02-2011, 06:32 AM
can we have better pics of the undertray and fitting as from that pic there it doesnt look to good :bored:
captainlip
23-02-2011, 06:43 AM
you have pm :thumbsup:
jeffrey
23-02-2011, 08:45 AM
here is a pic of my undertray.
it fits perfect.
http://img820.imageshack.us/img820/7493/img0412gj.jpg (http://img820.imageshack.us/i/img0412gj.jpg/)
Uploaded with ImageShack.us (http://imageshack.us)
http://img839.imageshack.us/img839/5881/img0414h.jpg (http://img839.imageshack.us/i/img0414h.jpg/)
Uploaded with ImageShack.us (http://imageshack.us)
grtz
Bugle
23-02-2011, 12:51 PM
Here's a few more of a clear undertray minus the bumper
https://lh3.googleusercontent.com/_f_qpmXnmt0k/TWT71dPRJnI/AAAAAAAAARg/nwLdPJhX7rE/undertray1.jpg
https://lh6.googleusercontent.com/_f_qpmXnmt0k/TWT8Os3brZI/AAAAAAAAARo/Syex-VpYKJM/undertray2.jpg
https://lh3.googleusercontent.com/_f_qpmXnmt0k/TWT8nagtJhI/AAAAAAAAARs/5M9a41vo8Xc/undertray3.jpg
I made the mould out of a block of wood and you can see some of the wood pattern in it on the bottom, everyone tells me it doesn't matter because after a run you can't tell the difference with the scratches on it.I guess painting hides it just fine too :)
X5 Addict and others i've seen have put extra holes in their ones at the front brace post screws to hold it on better, some thin double sided tape on the sides would hold it there alright too probably. ALso they've clamped the back of the undertray down under the brass weight. You wouldn't do this with the plastic skid plate though, best to leave the undertray overlapping that to avoid the skid plate getting ripped off.
captainlip
23-02-2011, 12:56 PM
thankyou :thumbsup:
captainlip
23-02-2011, 03:38 PM
If you guys havent seen it yet there is now a groupbuy offer for the UK!
http://www.oople.com/forums/showthread.php?t=64008
Nigel
23-02-2011, 05:07 PM
hey bugle do you think sometime in the future you could start selling them off ebay? it just makes it a lot easier for me to get one as im in Canada.
Bugle
24-02-2011, 09:58 AM
I will probably list some on Ebay soon, I can send to Canada either way, just PM me if you're interested
BostonNelson
02-03-2011, 01:13 AM
Another Bugle body ready to race :).
brettness37
02-03-2011, 01:17 AM
My girl just texted to let me know a package arrived from Australia.
Incredible! I believe they were posted 5 days ago!
Bugle
02-03-2011, 11:50 AM
Damn that is quick, wish it was that quick the other direction!
Finally received the material for making more bumpers to everyone who wanted one, I should be able to get a load of bumpers made tomorrow.
Cool paintjob bostonnelson, first durango i've ever seen with an external antenna :)
BostonNelson
02-03-2011, 12:07 PM
Did what I could with spray cans. Guess the external antenna shows I'm a newbie :lol:.
The chicks are gonna rape me now. With a 1:1 BMW and a 1:10 Bugle DEX410 one is pretty fly, for a white guy :drool:.
pjs autos
05-03-2011, 03:29 PM
hi mate u got any of the new shells wats u made mate:thumbsup: i want 1 please
pjs autos
05-03-2011, 03:30 PM
u got a durango shell u making :thumbsup: i want 1 of these please:thumbsup::thumbsup::thumbsup:
OoD1S
10-03-2011, 07:35 AM
Got my shell and under tray today must say that the under tray is all class, shell is very good but i prefer the tresrey one. Is a very good purchase over the stock stuff, no more heat problems for me and im in QLD Australia 30+ degrees racing every meet.
BostonNelson
17-03-2011, 09:47 PM
Really recommend this shell. The heat is significantly lower compared to the stock shell.
Bugle
18-03-2011, 04:37 PM
Really recommend this shell. The heat is significantly lower compared to the stock shell.
Good to hear :thumbsup:
Any special cooling setup on the motor or just fine without?
BostonNelson
19-03-2011, 02:15 PM
No, just a fan on the esc but nothing on the motor. But, I guess the real test comes during the hot summer days (it's winter here now :thumbdown:). And another test will be the EOS pilot in Sweden in a couple of weeks. http://eos.redrc.net/series/
Bugle
22-03-2011, 10:22 AM
Yeah it's no fair you get indoor offroad tracks!
We have to keep rebuilding our track because every time there's a decent downpour it washes half the track away. Happened last weekend.. :thumbdown:
It'll survive summer even if you have to chuck a fan in there, how hot does it get in Sweden?
Bugle
22-03-2011, 10:37 AM
Another thing, bodies from now on will have overspray film on them to make things easier if you prefer trimming the body before painting. With the latest polycarb i've got they've improved the protective film so I can leave it on there..
There's cutting lines on it, they just don't show up in the pic
https://lh3.googleusercontent.com/_f_qpmXnmt0k/TYh3F0pzEAI/AAAAAAAAATk/VqiHf9vagV4/clearbody.jpg
Gonzo
26-03-2011, 07:17 PM
My Bugle body inspired by the video game Wipeout (the wing is not Bugle yet)
http://www.wipeout-game.com/html/content/TeamInfo?team=AG_Systems
http://i304.photobucket.com/albums/nn169/gonzothegreat999/Photo0058.jpg
http://i304.photobucket.com/albums/nn169/gonzothegreat999/Photo0060.jpg
simoncrabb
26-03-2011, 07:57 PM
Wow! It's like being back in 1986.
Shells received yesterday! :thumbsup:
Excellent finish, thanks dude!!!
hottuna
31-03-2011, 03:30 PM
Got mine today, as said before, excellent work Thomas! :thumbsup:
Gonzo
01-04-2011, 09:37 AM
Wow! It's like being back in 1986.
Duct tape and spray cans FTW! :thumbsup:
Bugle
02-04-2011, 03:14 AM
Glad you guys like em :thumbsup:
Just need that Atomic Carbon tub now hey SHY :drool:
I'm usually the same Gonzo, too impatient to wait for liquid mask to dry or to get the compressor out, I should buy a hobby sized one. Could've saved the money I spent on spray cans and got one..
Oh yeah, that's goona be sweeeeeeeeeeeeet! :wub
Arnefles
09-04-2011, 08:05 PM
Me too, got mine (3pcs) yesterday. Looks great!
Great service!
Thank you so much!
Arne-P.F.
JosephShanks
18-04-2011, 11:21 PM
Bugle, two of our local racers started a hobby shop a little while back. I just sent him a link to this thread letting him know about your bodies.:thumbsup: Hopefully he can bring you some business. Once my current body is a gonner I will be hitting you up as well.:lol: Joseph.
Bugle
20-04-2011, 02:06 PM
Sweet, always happy to make more :thumbsup:
JustARcFan
20-04-2011, 02:15 PM
Maybe you can make something for the vega.
I'm sure you will have LOTS of business :woot:
Sweet, always happy to make more :thumbsup:
Bugle
21-04-2011, 10:52 AM
What body do they normally run on the Vega? I can't find a pic with a body on it :)
Bugle
21-04-2011, 11:22 AM
Should've just looked at the Vega section here instead of Team xtreme website, interesting looking standard shell :)
JustARcFan
21-04-2011, 11:33 AM
Interesting it is for sure!
You think you can make a shell for it?
Should've just looked at the Vega section here instead of Team xtreme website, interesting looking standard shell :)
Bugle
21-04-2011, 12:23 PM
Dunno, looks tricky to design something with the spur as high as it is, or maybe that's an illusion created by the tiny cab. Too bad the spur doesn't have its own cover so you could just work around it. I'd have to get my hands on a standard shell , where can you buy them?
JustARcFan
21-04-2011, 03:59 PM
You can buy thema on the team extreme site. Vega section. Thanks
drobec
30-04-2011, 03:56 PM
Yesterday I received a nice package from Australia :thumbsup: Quality of body, wing and undertray is great! I was suprised with the wing, it´s more like a showel, it´s HUGE! :) Here are some pics:
http://img7.rajce.idnes.cz/d0701/4/4778/4778010_9a7600757fb79f150ca14092ae399e89/images/P4300472.jpg
http://img7.rajce.idnes.cz/d0701/4/4778/4778010_9a7600757fb79f150ca14092ae399e89/images/P4300474.jpg
http://img7.rajce.idnes.cz/d0701/4/4778/4778010_9a7600757fb79f150ca14092ae399e89/images/P4300475.jpg
http://img7.rajce.idnes.cz/d0701/4/4778/4778010_9a7600757fb79f150ca14092ae399e89/images/P4300476.jpg
Painting´s pretty poor but it´s fun for me, I like to paint my bodies myself.
caneye
02-05-2011, 12:29 AM
very nice!
you need matching wheels ;):thumbsup:
drobec
02-05-2011, 07:37 AM
Matching tyres are more important. ;) Car is only borrowed for this season (thanks to bagman for BIG support) and wheels came with it. I ordered Bugle body because electronics from Cat couldn't fit with standard one. Btw. I copied window design from fastinfastout, looks bit like Le Mans prototype.
Bugle
02-05-2011, 04:12 PM
Nice paint, nothing wrong with that :thumbsup:
Martini livery is always a winner
lochness42
02-05-2011, 05:10 PM
Looks good, but will try to beat you this season again regardless of shell or car :D
drobec
03-05-2011, 12:05 PM
@Bugle: Thanks, body's worth these colors, you can't put them on every car, has to be something legen...wait for it...dary. :D
@lochness: Like it's a big thing for you to beat a noob like me :D
BostonNelson
01-06-2011, 03:11 PM
Should have bought the undertray as well :)
https://lh4.googleusercontent.com/-zyhIciPj5Lk/TeKTdiKnH4I/AAAAAAAAAD0/JqO9DWFY_84/s640/255760_2070338439226_1267815377_2395075_4342076_n. jpg
Wonderflupke
11-07-2011, 09:04 PM
http://nsa27.casimages.com/img/2011/07/11/110711110902578339.jpg
Briangb
12-07-2011, 09:11 PM
Very nice shell Wonderflupke.
What shell is it?
caneye
12-07-2011, 11:40 PM
Briangb - it's the same shell as all the other cars on this page ;)
it's made by "bugle".
Bugle
13-07-2011, 04:22 AM
Yeah cool paint job :thumbsup:
Cool track too, every track needs a wall
Briangb
13-07-2011, 10:26 AM
Hi caneye.
Thanks for pointing that out.
I had seen the same photo on the 'Show me your Durango' thread, and just went straight to the last page on this one without reading it.
It does look a nice shape shell though.
Wonderflupke
13-07-2011, 08:40 PM
Track of MBV Kampenhout ===> Belgian GP!!!
Paint by Mikovic.
Thanks for compliments. ;-)
Wonderflupke
13-07-2011, 08:48 PM
With my friend Gaetan's body.
http://nsa28.casimages.com/img/2011/07/13/110713105425249559.jpg
syllag1969
19-01-2012, 11:35 AM
Thomas is a great guy to deal with and his bodies are just awesome!
Here are my painted shells for my Durango 410R and Losi 22 :)
matthew
19-01-2012, 05:27 PM
With my friend Gaetan's body.
http://nsa28.casimages.com/img/2011/07/13/110713105425249559.jpg
hi guy's just want to know where I can buy these oople stickers from. Thanks :wub
MrMagoo
28-01-2012, 02:38 PM
Finally got around to shooting some colour onto one of my Bugle shells. I have to say these shells are excellent, good fit, quality production and a really good fit!
http://images16.fotki.com/v377/photos/1/1116472/5235375/2012012811_47_14-vi.jpg
eyeayen
29-01-2012, 02:32 PM
Nice colours dude, good design :)
Bugle
31-01-2012, 12:13 PM
Cool paint schemes :thumbsup:
Matthew, ask Jimmy about stickers , he visited my club here in Sydney a couple of years back and gave us some of those stickers :)
buhade
22-02-2012, 05:12 PM
my bugledex
my bugledex
Super!!! :thumbsup:
MarkLeeds
23-02-2012, 03:58 PM
my bugledex
Nice paint, did you do it yourself:thumbsup:
buhade
24-02-2012, 07:01 PM
No, it was mad buy dubidesign.cz
Bugle
26-02-2012, 09:05 AM
Turned out pretty sweet, is the black bit carbon fibred? Need to get it out in the sunshine :thumbsup:
buhade
29-02-2012, 04:58 PM
yes carbon fivred!!!
st33v3
06-11-2013, 04:14 AM
Do you still sell that body?
I'm interested in one, shipped to Canada with the undertray.
Let me know :)
Here's the link to his website, http://bugleboyracing.com/index.php?productid=1, looks to have 5 in stock.
st33v3
06-11-2013, 06:06 AM
Thank you!
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.