22 REAR WEIGHT Cream Extreme RC + V2.0

[Cream]

Up date with V 2.0 16/09/2013

V2.0 now available....


http://img.photobucket.com/albums/v420/Creamuk/RC%20car%20parts/losi22v20rearweight_zpse5936220.jpg (http://smg.photobucket.com/user/Creamuk/media/RC%20car%20parts/losi22v20rearweight_zpse5936220.jpg.html)

Added m2 retaining hole and milled step to rear to clear higher rear gearbox step up.

They have slimmed down a little on weight due to the extra machining, and now weigh in at just over 40g. ( -2g over original version)

Part is backwards compatible with the original Losi 22.

Price will be held at £20.00


Thanks to paulj for his assistance on the v2.0


==================================================
IN STOCK 22/09/12



The losi 22 has now had a little bit of Cream Extreme work :)


http://img.photobucket.com/albums/v420/Creamuk/RC%20car%20parts/losi22rearweightbrass.jpg





Again made from brass and weighing in at 42g, which is 39g more than the rear hinge pin brace it replaces :) Sits perfectly just in front of the rear wheels which greatly removes the pendulum effect that rear end weight kits cause.

The price is £20 plus postage.




Postage cost...

Recorded postage is..

U.K. ...£2.50

E.U.... £8.90

None E.U. ...£9.40

[Chris Evison]

I used 1 of these yesterday at Southport, a track which is multi surfaced mainly astroturf. The quality of finish is excellent!!

When the track got very dusty the back end wants to kick out under acceleration when using the TLR rear weight kit, and also within the corner the rear end wants to come round and kick out. With the CREAM weight fitted and the TLR weight removed from the back the car is total changed, the mid corner speed is greater due to no fear of the rear end kicking out and also coming out the corner the car stays straight. All in all the new weight from CREAM increases forward and side bite.

The rear TLR weight will still also be needed on high bite tracks/conditions, just to calm the car down.

Cheers
Chris

[Cream]

Thanks Chris for your input. :thumbsup:


All PM's replied to, I'm all but out of stock of these now just 3 left, and I'm awaiting material to make the next batch...


Thankyou everyone who has ordered one.

Regards
Noel



Update,
2 left.

4 reserved for SRCC drivers and 1 for 'learnerdriver'


Please make sure I have some left before sending payment. I don't want to upset anyone.

Regards
Noel




More will follow......

[Cream]

Everyone who bought and paid for this part upto midnight last night, Your items have been disspatched and you should have them tomorrow.
:thumbsup:

[jonathan may]

Great service :thumbsup::thumbsup:

[Chris56]

Just arrived. Looks ace, can't wait to test it this friday:thumbsup::thumbsup::thumbsup:

[Robocop]

Got mine
Very nice

[jonathan may]

got mine in the post today Ace :thumbsup:

[Cream]

A few more back in stock boys..

[learnerdriver]

got mine in the post today, thanks :thumbsup:

[dirk702]

Like to order one of these !
Dear cream you got message from me ...(PM)

[Projectzip]

ill be creaming my 22

LOL

[Cream]

ill be creaming my 22

LOL

Steady :blush::o

[andys]

Got mine today - looks good.

Are people putting the anti squat shim under the weight, or shimming with washers above it ?

I'm running the degree shim, so it look a bit odd under the cream weight !

[steveproracing]

You will have to put antisquat shims underneath the weight as it now contains the wishbone mounts. If you just use spacers above all you will alter is the gearbox height and the wishbones will stay at zero degrees squat

You must use the shims under the weight to alter the front end of the wishbone height creating antisquat
Hth

[andys]

Cheers Steeve, makes sense !

[taz5311]

Received mine today, very nice.

[Projectzip]

Just got mine so currently my desk is being creamed!

LOL I could go on and on and on he he he

[charlie]

We ran ours this weekend at the Oswestry national, along with our JM08 shortened chassis. The car was transformed, brilliant quality and service. Thanks:thumbsup:

[Cream]

Thank's for the feed back Charlie :thumbsup:



Postage charge added to first post.

I've currently 2 in stock which are awaiting confirmation of purchase.

After that I'm hoping to have the next batch ready towards the end of this week or the start of next week.

[Projectzip]

Fitted mine took a little bit of a jiggle to get in but fits perfectly.

So whats the next product?

I need some under lipo (saddles) weight :thumbsup:

And if you made one and dont cut a logo out it will weight even more :D

[Cream]

Postage charge added to first post.

I've currently 2 in stock which are awaiting confirmation of purchase.

After that I'm hoping to have the next batch ready towards the end of this week or the start of next week.


One not been claimed, Checked to see that they have been online, which they have with no communication. So one back up for sale.


Chears
Noel


SOLD SUBJECT TO PAYMENT.

[Bazzokajoe]

any chance anymore will be produced soon? only just got my 22 and these look awesome :D

[Cream]

any chance anymore will be produced soon? only just got my 22 and these look awesome :D
Hopefully the middle of next week mate.

[Chalkie]

Any news on when these will be ready again? Also do they fit fine with all the different anti squat shims LRC and HRC?
Cheers

[Cream]

Hope to have them ready on Monday bud.

Will work fine with the anti squat shims. Although it looks a little odd being a different shape. i.e. lifts the block off the chassis.

[serpentracer1]

Can you please tell me how much in American dollars to the states and where I need to order them with recorded postage

[Cream]

Can you please tell me how much in American dollars to the states and where I need to order them with recorded postage


I'm not sure what the current exchange rate is but the cost to the USA is £7.50 for postage.
So £27.50 in total if payed as a gift. Add 4% if your not happy paying as a gift via paypal.


To order one just PM with a request and I'll send you payment details. Paypal account etc.

Check out my feedback on this forum if you have any concerns.

Regards
Noel Grundy

[Cream]

OPEN TO ORDERS AGAIN....

[Legacy555]

Can you make some stainless anti-squat shims to match the outline of the block?

[Cream]

Can you make some stainless anti-squat shims to match the outline of the block?

I'm looking into it :D

[Chalkie]

Received mine today, I haven't run it yet but it's a fantastic bit of machining and fits perfect :thumbsup:

[rednoise]

Hi Cream ,
Some french 22 drivers and I would like 5 pieces!I hope you got them in stock.
Pm following!

thanks.

[Cream]

Hi Cream ,
Some french 22 drivers and I would like 5 pieces!I hope you got them in stock.
Pm following!

thanks.


Not a problem PM sent :thumbsup:

[DCM]

Just out of curiosity, could you make the weight bigger, I mean, is there room to make the Cream weight taller, wider etc?

[Cream]

Just out of curiosity, could you make the weight bigger, I mean, is there room to make the Cream weight taller, wider etc?

Not taller, it's basically the same as the HRC rear hinge pin brace it replaces. could get into issues with the gearbox if made taller.
There may be a shim kit to follow which will add more weight if that's the reason your asking. Just trying to find a way to make it cost effective.

[DCM]

dumb question, but this replaces the rear block?

[Cream]

dumb question, but this replaces the rear block?

Replaces this...
http://img.photobucket.com/albums/v420/Creamuk/RC%20car%20parts/TLR1065-2T.jpg

[DCM]

Cool, the front block.

[Cream]

Cool, the front block.


Yeah sorry for the confussion, I was meaning the rear suspension, not the rear, rear block :blush: Am I making things worse :p;)


Thought I had it covered with this...
Sits perfectly just in front of the rear wheels

[magnus]

Could you make a wider pivot as well? I need the inner pivot to be about 3-3.5mm wider than stock. I would need both front and back. How much you think. Would like to have the rear one in aluminium thought if possible? (to get rid of any pendleeffect.

[CraigP]

hello i was reading about this and was wondering if you had anymore of these pivots and if you would send one over seas to the united states? i would love to give this block a try. Thanks,

Craig

[Cream]

hello i was reading about this and was wondering if you had anymore of these pivots and if you would send one over seas to the united states? i would love to give this block a try. Thanks,

Craig


Hi Craig,
Yes I still have plenty in stock bud, The shocker is the postage to the USA is £7.50:bored:

But I'm more than happy to post them to the USA.

[TKG26]

This block is a drop in replacement correct? We still use our plastic inserts or shims depending on if we run Mid or Rear..

Have you shipped to Canada? Will you?

[Cream]

This block is a drop in replacement correct? We still use our plastic inserts or shims depending on if we run Mid or Rear..

Have you shipped to Canada? Will you?


Hi,
It's a direct replacment for the HRC.
Only fits to a mid motored set up.

To Canada, I have and will again :) Cost is a bit of an issue thought with recorded postage being £7.50.

[CraigP]

Hi Craig,
Yes I still have plenty in stock bud, The shocker is the postage to the USA is £7.50:bored:

But I'm more than happy to post them to the USA.

How would i go about ordering 2 of these? on here or do you have a website?

[Jaune]

TKG26, I would split shipping with you...:D

[Legacy555]

Could you make a wider pivot as well? I need the inner pivot to be about 3-3.5mm wider than stock. I would need both front and back. How much you think. Would like to have the rear one in aluminium thought if possible? (to get rid of any pendleeffect.

You've read my mind!!

Cream: Will you be offering these?

[Cream]

How would i go about ordering 2 of these? on here or do you have a website?


Just send me a PM and I'll send you all the details bud.

[Cream]

You've read my mind!!

Cream: Will you be offering these?


No plans currently to make anything but the standard HRC rear weight, making small batches/one offs is very time consuming and expensive.

Even the shims i've only one person asking if I'm going to make them. So I'm guessing it's not something people want/need. :bored:

[magnus]

At first a figured that a wider pivot would be enough and simply cut the hexes to get the right measures of the car. Although I think it will make the driveshafts run to far out in the outdrive. So the best thing would be both new pivots and hubs to go with them.

[s22jgs]

im a little confused lol

This is the rear front block right?
Does that mean it can be directly swapped for the one i currently have in, or do i have to change to the rear HRC blocks as well. Currently running LRC with no real plans to change to HRC

[Cream]

im a little confused lol

This is the rear front block right?
Does that mean it can be directly swapped for the one i currently have in, or do i have to change to the rear HRC blocks as well. Currently running LRC with no real plans to change to HRC

It's dimensionally the same as the HRC block. i.e hole hight and slot depth(where plastic inserts go)

[s22jgs]

It's dimensionally the same as the HRC block. i.e hole hight and slot depth(where plastic inserts go)

I didn't think the rear front block had to be changed for using the rear rear hrc block. That's where I'm confused.
In short can it be used along with the rear rear lrc block or does it need to be used along with the rear rear hrc block

[Cream]

I didn't think the rear front block had to be changed for using the rear rear hrc block. That's where I'm confused.
In short can it be used along with the rear rear lrc block or does it need to be used along with the rear rear hrc block


I'm just trying to get it clarified, I was given a sample to work to for the original product. I was then told that it was a HRC by someone else 'if I was ever asked'
Just trying to get in touch with Chris Evo to clear it up. Sorry for the confussion, I'll get back to you ASAP. As far as I know, this part doesn't change weather you have HRC or standard.

[s22jgs]

I'm just trying to get it clarified, I was given a sample to work to for the original product. I was then told that it was a HRC by someone else 'if I was ever asked'
Just trying to get in touch with Chris Evo to clear it up. Sorry for the confussion, I'll get back to you ASAP. As far as I know, this part doesn't change weather you have HRC or standard.

Ok thanks. I want one but I run with lrc so if its just a straight swap its all good.

[TKG26]

TKG26, I would split shipping with you...:D

Sounds like we need a group order! Ill leave it you hands. :) Yes Ill split with you.. We could probably order 6 of these

[Cream]

Right,

To clear this up, The part works with both HRC and LRC as it's a universal part. you just buy the standard shim kit that suits your setup. THis has been confirmed by Team driver Chris Evison.

Sorry about the confusion, I was just throw a duff call by someone I thought knew what they where talking about.

So to confirm.

This is for a midmotor set up with high or low roll centre.
You use the standard shim kits that come with the kit or the shim kit you get for a HRC.

It fits at the front of the rear suspension, with the angle fitting under the motor.

[Cream]

Sounds like we need a group order! Ill leave it you hands. :) Yes Ill split with you.. We could probably order 6 of these

IF and I know it's a big if you do get to 5+ I could give a small disscount. Same as I did for http://www.rc4ever.com

1 off : £20.00
5 off : £19.00 each
10 off : £18.00 each
20 off : £16.00 each


With a single cost postage. i.e. not going up due to weight.

[CraigP]

sent you a pm cream, cant wait to try them

[Marc0]

I have it in my 22 since last week... and I am absolutely fond of this weight !

I tried weight under the lipo (75g), that helped a lot on my favorite track (high grip, traction astro / carpet) but with your rear weight is much better : the car seems to make exactly what I think about.
There is no side effect like with the TLR rear weight : we have more traction, but the rear is still able to rotate without rolling too much.

Thanks a lot cream, you made my TLR 22 experience much better ! :D

[Cream]

Thanks Marc0, So glad your happy with it :)

BTW just 3 left of this batch...

[Jaune]

Wow It took a week to get them to Canada :)

Very nice pieces. Thanks CREAM!

[TKG26]

thanks as well... Think ill cream my 22 tonight :)

[CraigP]

hopefully mine comes tomorrow so i can try it sat, going to the track for all day practice.

[Cream]

hopefully mine comes tomorrow so i can try it sat, going to the track for all day practice.


Might be pushing it, Only a week to America, but you never know :)

Thanks for the coments guy's. Please don't forget to leave me feed back in the traders section. Good, bad or indifferent as long as its honest and preferably constructive ;)

[CraigP]

nope didn't come today, but i know as soon as it does my mid motor is getting creamed then thrown on the track for practice.

[CraigP]

Got it today. I have to say you do awsome work thanks.will post on here thoughts after running it =)

[Cream]

Got it today. I have to say you do awsome work thanks.will post on here thoughts after running it =)


Thanks for the feed back..


BTW

out of stock again....

[Cream]

BLOCKS BACK IN STOCK 15/09/2011

[Jaune]

Might not be related but ive won the last two races at my local track, right after my 22 was creamed.

[Cream]

Might not be related but ive won the last two races at my local track, right after my 22 was creamed.

Of course it's related ;) I'm taking 100% credit for your wins :blush:

[Jaune]

Haha i have no problem with that, now if you want more credit, you could also work on a rear motor weight so i can compete on dirt this winter :)

There is not as much room but im sure a eaviyer piece could fit there as well.

[(off)roadrunner]

do you have any weights in stock at the minute?

[Cream]

I've plenty in stock bud.

[cryer-evo]

i am thinking of getting one of these as i want as much rear end grip as i can get so if my thinking is right i need one of these and to run the 3 degree anti squat ?

i mainly run 1/10th gt pan cars so i am used to having lots of rear traction as i use the power and rear end grip to steer rather than the steering if you know what i mean if i want it to go wide i just put more power on and if i want it to turn tighter i just get off the gas

[Cream]

For what I know most are settling for around 1 degree of anti squat. But yes the weight will give you more rear grip, But with no pendulum effect as the weight is infront of the rear wheels.

[zleader]

Thanks for shipping to Canada.. Got it today...

Do most people run your block with the losi weight set? I am running mainly mid high bite carpet. Thanks

[Jaune]

Thanks for shipping to Canada.. Got it today...

Do most people run your block with the losi weight set? I am running mainly mid high bite carpet. Thanks

Im running without on a high bite carpet track. I do have a some weight on the right side but nothing behind the wheels. The car was the fastest on the track last week.

[Cream]

Thanks for shipping to Canada.. Got it today...

Do most people run your block with the losi weight set? I am running mainly mid high bite carpet. Thanks


From the feedback I'm getting, Many are not using the rear weight, but choosing to use this weight instead to get rid of the pendulum that is associated with the losi weight set.

I'll just add this quote.
I used 1 of these yesterday at Southport, a track which is multi surfaced mainly astroturf. The quality of finish is excellent!!

When the track got very dusty the back end wants to kick out under acceleration when using the TLR rear weight kit, and also within the corner the rear end wants to come round and kick out. With the CREAM weight fitted and the TLR weight removed from the back the car is total changed, the mid corner speed is greater due to no fear of the rear end kicking out and also coming out the corner the car stays straight. All in all the new weight from CREAM increases forward and side bite.
The rear TLR weight will still also be needed on high bite tracks/conditions, just to calm the car down.

Cheers
Chris

Chris is a losi team driver, he along with sly asked me to produce product this in the first place, I'm very happy to say he is still using it. So I guess the answer is try it and which suites you best.


P.S. thanks for the feed back Jaune. :)

[zleader]

Thanks guys

[AmiSMB]

Did some back to back testing last night at Bracklesham Barn club with TLR weight, No TLR weight and the Cream RC weight and it was much better with the Cream RC weight. No pendulum, loads more rear end grip even with tyres starting to go off.

[Getpip]

Fitted the 'Cream' weight in my 22...
Seemed to work really well.
Pic here: http://pipskiracing.blogspot.com/2011/10/losi-luvvin-tlr22-hits-track.html

[cryer-evo]

Hi there I would like one of these do you have them in stock and do you have Pay pal ?

[drop4205]

yes he does paypal but he told me before i placed my order that he will be on vaca till Wednesday

[cryer-evo]

Ok thanks for info

[Cream]

Been away a few days, Think I have PMed everyone about these, If I've missed anyone please send me another PM.
Chears
Noel

P.S.

cryer-evo Plenty in stock, Just send me a PM and I'll go through ordering with you bud.

[cryer-evo]

I have sent pm

[cryer-evo]

Payed by PayPal today

[cryer-evo]

Got my cram weight top marks but it has made my car very rolle in the corners has any one els found this ? And is there a cure for it

[Fred79]

Stiffer springs and oil :) and less camber gain on the rear

[kayce]

Got my cram weight top marks but it has made my car very rolle in the corners has any one els found this ? And is there a cure for it

Not sure what you mean by this.... :confused:

[peetbee]

Got my cram weight top marks but it has made my car very rolle in the corners has any one els found this ? And is there a cure for it

Not sure what you mean by this.... :confused:

He means:

I have received the weight from Cream.
It is jolly good, but it makes the car roll quite a lot when cornering.
Has anyone else experienced this and what can I do to prevent this from occuriing?

:D

[kayce]

He means:

I have received the weight from Cream.
It is jolly good, but it makes the car roll quite a lot when cornering.
Has anyone else experienced this and what can I do to prevent this from occuriing?

:D

Considering how inexplicably low he had his ride height set the other week (while complaining about inside front wheel lift in the corners), and without any follow-up or noted changes since then - and the fact that just a touch of low mounted weight isn't going to make it happen - I'm really more interested in getting the WHOLE story of what else he's done, along with wondering if he's got the best eyesight on the planet that he can see these things from the rostrum. ;)

[cryer-evo]

right then car set up is mid mount

front
25 kick
5 deg caster
55 piston
red spring
27.5w oil
shock middle on tower/ inside on arm
tyres mini pins
all links as kit spec

rear
tow 4 deg
2.5 antisquat
55 piston
white spring
20w oil
shock middle on tower / inside on arm
cream weight
chassis in its short config
mini pins
all links as kit spec
ride hight as low as pos when racing indoor on carpet

out cide on astro and grass the same but with fastrax turf grippers all around and running rear arms level with front maching so chassis is level

[kayce]

Rear shock oil weight is too low compared to what is being used in the front.


ride hight as low as pos when racing indoor on carpet
What is that exactly, because last week you were running something crazy like 15mm rideheight.

[steveproracing]

Your front shock setup is a little off.
Put 2.5mm internal spacers in shock to calm some of the weight transfer on power
Your front springs are way too soft for carpet and minipins
Go for a green spring and move bottom of shock to middle
camber link should remain kit but remove the 2mm under ball stud as this causes the car to hold on to the corner too long


Now for the rear.
Your oil piston is not as far out as kayce would make out!

Try 27.5wt but with the 54 piston
Keep the white springs
Move the upper mount to outer to help support the car mid corner

Rear camber link works really well with 1e. With 3mm under outer ball
Keep everything else the same as you describe

Oh and go for around 18mm ride height all round


This setup is proven to work really well on carpet
It's very easy to drive with no negative traits
In fact its a really good standard setup for grass and astro aswell.
It only every requires fine tuning to track or driver preferences

[cryer-evo]

Your front shock setup is a little off.
Put 2.5mm internal spacers in shock to calm some of the weight transfer on power
Your front springs are way too soft for carpet and minipins
Go for a green spring and move bottom of shock to middle
camber link should remain kit but remove the 2mm under ball stud as this causes the car to hold on to the corner too long


Now for the rear.
Your oil piston is not as far out as kayce would make out!

Try 27.5wt but with the 54 piston
Keep the white springs
Move the upper mount to outer to help support the car mid corner

Rear camber link works really well with 1e. With 3mm under outer ball
Keep everything else the same as you describe

Oh and go for around 18mm ride height all round


This setup is proven to work really well on carpet
It's very easy to drive with no negative traits
In fact its a really good standard setup for grass and astro aswell.
It only every requires fine tuning to track or driver preferences


hi there thanks for the info would the info you have given me for the front be good on astro /grass our is that just for carpet with mini pins ?
on the astro/grass track i race on i am running mini spikes front and rear also the astro/grass track is very bumpy as it is normaly a 1/8th rally cross track and is in ledbury

[kayce]

hi there thanks for the info would the info you have given me for the front be good on astro /grass our is that just for carpet with mini pins ?
on the astro/grass track i race on i am running mini spikes front and rear also the astro/grass track is very bumpy as it is normaly a 1/8th rally cross track and is in ledbury

Why is it that you're using, or asking about using, indoor carpet/ozite set-ups when you're now saying you're running outdoors on astro on a very bumpy track with 1/8th-sized jumps? :confused:

[cryer-evo]

i race every friday indoor on carpet
but as i have done my first meet out cide on astro / grass i would like to get a good sut up for this as this is the main race i wont to do well in

[steveproracing]

Start with exactly the same setup for the outdoor track as the setup I have given u for indoors
If the car is a little lively over the bumps then raise the car a mm or two
If still not right then go to 25wt oil all round

Most important though. Follow all my changes. Not just a couple of bits here and there as they all work with each other to create a balanced car

Hth

[cryer-evo]

Thanks I will give it a go

[kayce]

i race every friday indoor on carpet
but as i have done my first meet out cide on astro / grass i would like to get a good sut up for this as this is the main race i wont to do well in

This topic is supposed to be about the "REAR WEIGHT made by Cream Extreme RC," let's keep it on-topic.

There are dozens of set-ups already listed here on this forum, as well as many others used by team drivers on TLR.com - and it seems you should be able to find something that works - and a big part of RCing is a willingness to try things, and find out what works for you and your driving style and the tracks you run, and not just randomly posting each week with a supposed issue after a minor change.
Good luck in your search.

[R4BX]

i race every friday indoor on carpet
but as i have done my first meet out cide on astro / grass i would like to get a good sut up for this as this is the main race i wont to do well in

HAHAHA jonny! I will remember this quote forever! 'won't do well in' haha!

[drop4205]

ran the cream weight last night for the first time. Gotta say at first I was running same times as without it per lap times. Then i took the TLR weight off the back and the car was much more consistent and I broke my track record by a lap. If you dont have the cream weight get it. You wont be disappointed at all.

[Cream]

For those asking where they fit. Here you go.

http://pipskiracing.blogspot.com/2011/10/losi-luvvin-tlr22-hits-track.html

http://1.bp.blogspot.com/-AivwVTalqFU/TpwyDYvEdpI/AAAAAAAAAdc/GSRxi1pRb-k/s320/002.JPG

[Cream]

Back out of stock, Hope to have some more around 28/01/12

[Cream]

:thumbsup: back in stock.....

[syllag1969]

Hi, i just pm'd you for an order

I'll wait for your response :)

Thanks

[Cream]

Back down to just 7 left of this batch.

Chears
Noel

[Delves]

PM sent :)

[Cream]

PM sent :)


Sorry, last one of this batch is awaiting a reply to a PM I got over the weekend(as I was away) If they decide they now don't want it I'll send you a PM.
But you will have to set up a paypal account as a Don't accept cheques.

Regards
Noel Grundy

[Delves]

Sorry, last one of this batch is awaiting a reply to a PM I got over the weekend(as I was away) If they decide they now don't want it I'll send you a PM.
But you will have to set up a paypal account as a Don't accept cheques.

Regards
Noel Grundy

Ok, let me know :)

[dhann42]

Sorry, last one of this batch is awaiting a reply to a PM I got over the weekend(as I was away) If they decide they now don't want it I'll send you a PM.
But you will have to set up a paypal account as a Don't accept cheques.

Regards
Noel Grundy

Noel

Sent payment thanks hope u had a good weekend

Thanks David

[Cream]

Noel

Sent payment thanks hope u had a good weekend

Thanks David

Thank you David,


So that's it OUT OF STOCK..


Hope to have some more made next week.

[dhann42]

Noel

Big thanks weight came today look good give it a go next week

Davie

[Cream]

Now available, but now in brass, Same weight and same price at £20.00 plus postage..

http://img.photobucket.com/albums/v420/Creamuk/RC%20car%20parts/losi22rearweightbrass.jpg

[Delves]

Received my weight today after placing the order with Noel yesterday, thanks for getting it out to me so fast fella :thumbsup:

[Cream]

Received my weight today after placing the order with Noel yesterday, thanks for getting it out to me so fast fella :thumbsup:


Don't forget, if you use the losi rear weight, try it without that weight on the back.

[Cream]

First post updated with the new postage costs :cry:

[Shaun_TLR]

Are these back in stock currently?

[Cream]

Are these back in stock currently?


Yep, Plenty in stock. :thumbsup:

[Shaun_TLR]

So what does this kit do different than the TLR kit?

[Cream]

So what does this kit do different than the TLR kit?


In a nutshell, Adds rear traction without giving the car the pendulum effect of having the weight out the back.

Chris Evison (post 2) is a team driver who drives at Southport, my local track. He asked me to look into making something and this is what I came up with. 10 months later and he still has it in his car. I'm guessing it does what he wanted it to do :)

[Cream]

Shameless bump :o

[CraigP]

i was wondering if you had any in stock, i have bought 2 already one for my buggy and another i put in 22t, now i need another for the 22sc thats backorderd for me =)


Craig

[Cream]

i was wondering if you had any in stock, i have bought 2 already one for my buggy and another i put in 22t, now i need another for the 22sc thats backorderd for me =)


Craig

Hi Craig, yep plenty in stock :), I've still got a couple of stainless ones in as well if anyones interested in them.

[crazyasso]

I will try this Optionpart. Please sent me a PM. How we buy and sent it to Germany.

[Cream]

I will try this Optionpart. Please sent me a PM. How we buy and sent it to Germany.


PM sent, bit of as rush on these today from Germany, Have I hit another forum or something?

[Ensonic]

I think the reason for this is the German 2WD Masters next weekend, where everyone is looking for the last extra tenth of seconds :D Just got a 22, too and as soon as I can test on the track after the masters, I perhaps will order one set too :D

[Sewey]

Hi, I would like to buy one of these, I will not be able to do so until the 1st but can u reserve one for me for the time being

[Cream]

Still got plenty in stock, So shouldn't be a problem.

[Sewey]

Thanks:)

[Sewey]

How do i pay you, am new to the forum

[Cream]

How do i pay you, am new to the forum


Via paypal, Send me a PM and I'll send you the details.

Cheers
Noel

[Sewey]

How do i pm you, sorry for the stupidity, i have never really used a forum before, thanks, sorry, i can't get any money until the first so i will have to wait till then. Thanks

[Cream]

^^^^

click on my name then send a private message to cream.

you can see youe messages just below where it says Welcome, Sewey on the right hand side.
;)

How do i pm you, sorry for the stupidity, i have never really used a forum before, thanks, sorry, i can't get any money until the first so i will have to wait till then. Thanks

[Cream]

The bad news is if everyone who's asked about payment for these actually sends payment I've run out.:thumbdown:
The good news is I should have some more finished by tomorrow :thumbsup:

thanks everyone for your ordered :wub



Don't really want to bump the thread again, So I'll jut edit this to add that they are now

BACK IN STOCK :thumbsup:

[canon67]

Yep, Plenty in stock. :thumbsup:

Hey I will be ordering a couple of this for us guys up in Canada were can I order can’t find your site.

Cheers

Den.

[Cream]

Hey I will be ordering a couple of this for us guys up in Canada were can I order can’t find your site.

Cheers

Den.

Sorry bud I don't have a site yet. If you PM me I'll send you all the details you need.

You can check out my feed back here
http://www.oople.com/forums/showthread.php?t=19612


cheers
Noel Grundy.

[canon67]

Ok thanks Noel I will PM you at the end of the week I am waiting on other to split the shipping charges.

Den.

[JJM844]

Got my cream weight today, quality item, good machining, thanks for the speedy shipping. Same applies to the rear Camber mod:thumbsup:

[hdc]

Cream parts well-arrived in france today !
excellent job !
Hope to try them quickly on my 22 !

Thanks a lot Noel !:lol::lol::lol::lol:

[Cream]

Cream parts well-arrived in france today !
excellent job !
Hope to try them quickly on my 22 !

Thanks a lot Noel !:lol::lol::lol::lol:


Don't forget if you have the losi rear weight on, Try removing it. Thank's for letting me know it has arrived.

[mr. losi]

do you ship to the states?? and if so how much would it be??


MAtt

[Cream]

do you ship to the states?? and if so how much would it be??


MAtt


Hi Matt,
Yes I do ship to the states, it is expencive though at £8.95 for signed for delivery.
I've had a few in the past split the cost with other club members wanting other parts.

Cheers
Noel

[mr. losi]

i am not familiar with the conversion from euro to us dollar, how do i order ...i am thinking the wt. and the camber link

thanks..
matt

[Cream]

Cheeky bump for this very popular mod.
;)

[Cream]

Currenty this item is out of stock, I'll post again when I've produced some more.
Regards
Noel Grundy

[Bob_Zahn]

Currenty this item is out of stock, I'll post again when I've produced some more.
Regards
Noel Grundy

Would it be possible to make the mount longer so it could also attach to the chassis in the outside holes on the chassis (mid motor setup of course)?

I find it very difficult to change toein or antisquat and get all the parts lined up to reinstall. If the piece was fastened to the chassis with the outside holes it would make installation of the arms and toein block so much easier

I have considered drilling a hole in the stock piece between the existing holes and a corresponding hole in the chassis so it's fastened the same as the toein block with the smaller screw

[Cream]

Back in stock.....


Bob_Zahn there are other issues if I make them bigger to include the to outer holes for screwing, Currently the original shims can be used, If I made them to include the outer holes I'd need to produce shims as well, which would add greatly to the cost as the are all different thicknesses.

If people use the original shims on a redesigned wider weight they would either have screws coming loose or chassis bending.

[nicmo]

will be ordering mine finaly :)

[Cream]

will be ordering mine finaly :)


You have PM,

Cheers
Noel

[AndyRids]

Have sent you a PM Cream, to buy two.

[xlosi]

sent you a pm.

Felipe.

[cryer-evo]

Is this a new one Ie a mk2 ?

[Cream]

Is this a new one Ie a mk2 ?


No this is as the original post, There is no MK2. There are cost/design issues with producing a weight that uses the outer holes in the chassis.

[paulj]

Hi, I have PM'ed you about getting one of these weights. Thanks...

[paulj]

Got my order today, thanks.

[caciqueconnection]

Got mine ready to run,

Unfortunately weather is not giving a rest to try.

[schu84]

Got my order ! cheers Noel

[vrooom]

does it use 2 extra screw (outer holes on ethier side of chassis) to hold the brace to chassis when you remove the gearbox? Do you have one without "weight" added?

[Cream]

does it use 2 extra screw (outer holes on ethier side of chassis) to hold the brace to chassis when you remove the gearbox? Do you have one without "weight" added?


Hi,
No it doesn't use the extra holes. The reason for this is that it uses the original shims and with the two outer holes being unsupported it runs the risk of either twisting the chassis or the screws coming loose.

[vrooom]

Mmm fair enough about chassis twisting, but what if you put washers + screw to suit, afterward you fitted those 2 screw into gearbox first ?

Im looking for a brace that does hold the suspesion in place, when i remove the gearbox, its no fun looking for bits in grass/carpet.

[Swell]

Hi im just trying to get to grips with the cream wieght and anti squat im wondering :confused:
whitch plastic shim is the one to use the flat one?

Or the one with the tubular protursions ?

I want to get the most out if this kit so im keen to hear how others have found the best effect can be gained
(for them on what style of track and surface)
i think it could be good to compile as i have not seen the wieght included in any tlr set up sheets i have read unless i have missed somthing some where....

Cheers

[Cream]

Hi im just trying to get to grips with the cream wieght and anti squat im wondering :confused:
whitch plastic shim is the one to use the flat one?

Or the one with the tubular protursions ?

I want to get the most out if this kit so im keen to hear how others have found the best effect can be gained
(for them on what style of track and surface)
i think it could be good to compile as i have not seen the wieght included in any tlr set up sheets i have read unless i have missed somthing some where....

Cheers

The ones with the tubular protrusions go inside the slot of the weight, the thin shims go under the weight, Just a per the original brace.

Cheers
Noel

[Swell]

Yep i see that, the flat one is the anti squat then? (Under wieght) and if so whats the other do? (lift the gear box?)

[Cream]

Yep i see that, the flat one is the anti squat then? (Under wieght) and if so whats the other do? (lift the gear box?)


Yeah,
Follow the instructions in your Losi 22 manual. The offsets are no different to the original part.

If you have lost your manual you can down load it from here
http://www.tlracing.com/Products/Default.aspx?ProdId=TLR0022#prodManuals

[pje]

Have you any weights in stock, and how do i order?

/Jörgen

[Alan - South West RC]

Have you any weights in stock, and how do i order?

/Jörgen

I believe he has a couple in stock as I ordered one on Monday. Just PM him and he will give you all the details :thumbsup:

[pje]

Ok, done :)

[jimbo_468]

PM sent :-)

[Cream]

PM sent :-)


Sorry, Currently out of stock, I'm doing my best to get around to make some more. But just about everyone and everything is working against me. SO BUSY.........

[Cream]

Back in stock.....

[Cream]

V2.0 now available....


http://img.photobucket.com/albums/v420/Creamuk/RC%20car%20parts/losi22v20rearweight_zpse5936220.jpg (http://smg.photobucket.com/user/Creamuk/media/RC%20car%20parts/losi22v20rearweight_zpse5936220.jpg.html)

Added m2 retaining hole and milled step to rear to clear higher rear gearbox step up.

They have slimmed down a little on weight due to the extra machining, and now weigh in at just over 40g. ( -2g over original version)

Part is backwards compatible with the original Losi 22.

Price will be held at £20.00


I'll update the first post with the above information....

Regards
Noel Grundy

[Cream]

Back in stock.... YAY

[Simmo]

Super long shot!

Are there any of these 'in existence any more'? Sorry for the post resurrection.

Am running a 'vintage' 22 at my local track..