View Full Version : Questions
Lee Martin
06-07-2011, 08:52 PM
:thumbsup:Hi guys,
Been a little while, but thought i would ask if anyone has any questions they want to ask me? i try to read all the threads, but sometimes i loose track with being away so often.
Thanks
Lee
t8rtot
06-07-2011, 08:56 PM
can i get at least a baseline setup for a med/high grip indoor clay tracks. we're using aka rebars, barcodes and bk bars for tires. and as far as the rear aluminum hubs go, what differences will i see from 0-0.5-1deg?
your a champ Lee :thumbsup:
stegger
06-07-2011, 08:58 PM
Lee have you had anymore chance to test the 502 ?
Stotty
06-07-2011, 09:06 PM
There is a thread on here about a trf511 LME ( Lee Martin Edition)
Do you think this will happen if...... I meen WHEN you WIN the worlds.
:thumbsup::thumbsup::thumbsup:
Rich D
06-07-2011, 09:19 PM
511 gearing for Oswestry on a SP 5.5 V3.0 and a GT2.0 speedo would be handy !
BloodClod
07-07-2011, 05:11 AM
Hi Lee,
First off I want to express my thanks for your willingness to share your setups and tips with all your Tamiya buggies - must say that I've enjoyed my TRFs with your tips to experiment with.
I'm trying to get my TRF201 to work on the outdoor clay track that we run locally and I was wondering if you could share a little bit more about how you go about using weights to tune your car - e.g. when to put weight where and why...
Would go a long way in helping me get some better laptimes. :)
Thanks.
carpaste
07-07-2011, 06:16 AM
Hi Lee,
It is happy to see this topic. I am a your fan and Tamiya fan. I hope you will get the title of world race winner. I want to know that do you know whether Tamiya have had any plan for new top grade buggy model?
Thanks
DavidAMS
07-07-2011, 06:55 AM
Hi Lee, please drive more with the 502x :thumbsup:
It seems to have been forgotten??
Keep up the good work, everyone is rooting for ya!:thumbsup:
stegger
07-07-2011, 08:02 AM
:thumbsup:Hi guys,
Been a little while, but thought i would ask if anyone has any questions they want to ask me? i try to read all the threads, but sometimes i loose track with being away so often.
Thanks
Lee
Think he's gone away again ! :lol::lol::lol: :p
mattybucks
07-07-2011, 08:27 AM
:thumbsup:Hi guys,
Been a little while, but thought i would ask if anyone has any questions they want to ask me? i try to read all the threads, but sometimes i loose track with being away so often.
Thanks
Lee
Are you going to win the worlds?
lazyboy12300
07-07-2011, 08:56 AM
Are there any plans to release updated versions of the 801X and XT?
It seems you have done a fair bit of modifying these to help you in America. I have tried the +4mm wheelbase and I found it to make the car completely different, so looking forward to see what else you do.
Cheers
Scott
wildwillydriver
07-07-2011, 10:28 AM
Hi Lee,
this is very kind of you. :thumbsup:
I have 2 qeuestions for you:
1) Some set up guide line for TRF201 on dirt hard packed low traction tracks.
2) Next year i'd like to go nitro and since i'm "Tamiya only" i'll go for a TRF801x. Any chance that we will see them easily available also here in Europe? Can you give me some advice on were to find car and parts(Europe/UK)?
Some time ago you posted a topic about you as a future TRF distributor for UK and Eu, am i wrong? If not there is any update about this? :drool:
Thanks in advance for your time.
Bye
WWD
:)
Shifta
07-07-2011, 12:46 PM
Hi Lee, please drive more with the 502x :thumbsup:
It seems to have been forgotten??
Keep up the good work, everyone is rooting for ya!:thumbsup:
You've already taken the UK national series with 4 straight wins with the 511 so for the sake of all the people who bought the 502 it would be nice to see you run it for the 2 remaining meetings.. I think it would help us all out with set ups etc.. Thanks:thumbsup:
Lee Martin
07-07-2011, 08:28 PM
can i get at least a baseline setup for a med/high grip indoor clay tracks. we're using aka rebars, barcodes and bk bars for tires. and as far as the rear aluminum hubs go, what differences will i see from 0-0.5-1deg?
your a champ Lee :thumbsup:
Of course; start with:
35wt front - blue spring - 1.3 x 2 piston
Middle hole on the arm - 2nd out on the tower
inside hole on link with 1mm washer - 3mm washer outside.
30wt rear - yellow cut spring (1 coil off) 1.4 x 2 piston
Inside hole on arm - 2nd out on tower
try meduim wheel base.
with regards to the hubs:
the more toe in you have - the more rear side bite the car will generate.
the less, the looser the rear end. sometimes you can even turn the .5 blocks around so overall you have 2.5 degrees of toe in. this helps the rear end pivot on slow twisty tracks.
lee
Lee Martin
07-07-2011, 08:29 PM
Lee have you had anymore chance to test the 502 ?
Basically no.
i will not test te 502x until after the worlds. i want to be completely in tune with my 511 with no distractions. afterwards i will test the car again and get some great set ups!
Lee Martin
07-07-2011, 08:30 PM
There is a thread on here about a trf511 LME ( Lee Martin Edition)
Do you think this will happen if...... I meen WHEN you WIN the worlds.
:thumbsup::thumbsup::thumbsup:
Who knows... i have been working closely with the designer about the possibility of some upgrades....
time will tell, but i hope so...
Lee Martin
07-07-2011, 08:30 PM
511 gearing for Oswestry on a SP 5.5 V3.0 and a GT2.0 speedo would be handy !
im going to start with 19/91 standard ESC settings.
;)
Lee Martin
07-07-2011, 08:32 PM
Hi Lee,
First off I want to express my thanks for your willingness to share your setups and tips with all your Tamiya buggies - must say that I've enjoyed my TRFs with your tips to experiment with.
I'm trying to get my TRF201 to work on the outdoor clay track that we run locally and I was wondering if you could share a little bit more about how you go about using weights to tune your car - e.g. when to put weight where and why...
Would go a long way in helping me get some better laptimes. :)
Thanks.
Weights, recently i have been putting weights in and around the rear gear box, this has helps to increase rear traction quite a lot.
normally i use weights to stop the car grip rolling, settle it through bumps or to stop wheeling..... on dirt i normally run a light car with the weight (apprx 30g) under the rear U plate and in front of gear box, and also a small amount up front. (20-30) to stop wheeling.
Lee
GRIFF55
07-07-2011, 08:33 PM
Is it going to be orange?
Lee Martin
07-07-2011, 08:33 PM
Hi Lee,
It is happy to see this topic. I am a your fan and Tamiya fan. I hope you will get the title of world race winner. I want to know that do you know whether Tamiya have had any plan for new top grade buggy model?
Thanks
I hope so......
Thats up to the japanese im afraid.
Lee Martin
07-07-2011, 08:34 PM
Hi Lee, please drive more with the 502x :thumbsup:
It seems to have been forgotten??
Keep up the good work, everyone is rooting for ya!:thumbsup:
I will get back to it... i have just been working hard on preparing for the worlds and i dont want to confusion of 2 cars at the moment. For now the 511 is my chosen ride until we can dial in the 502x (after the worlds we will aim to do this)
Lee Martin
07-07-2011, 08:35 PM
Think he's gone away again ! :lol::lol::lol: :p
Back again ;) :p:p
Lee Martin
07-07-2011, 08:36 PM
Are you going to win the worlds?
Im going to be trying 110%. Fingers crossed for me!
AndyG
07-07-2011, 08:37 PM
I don't even run a Tamiya, but :thumbsup: to Mr Martin for putting himself forward to help on here. Good example to other sponsored drivers !
Lee Martin
07-07-2011, 08:37 PM
Are there any plans to release updated versions of the 801X and XT?
It seems you have done a fair bit of modifying these to help you in America. I have tried the +4mm wheelbase and I found it to make the car completely different, so looking forward to see what else you do.
Cheers
Scott
Aha, an 8th question ;)
Basically we have been doing more modifying! We will continue to modify and intensively do so over the winter months. i hope that with some strong results we can release a new car that is a race winner straight out of the box!!! both buggy and truggy!
Lee Martin
07-07-2011, 08:41 PM
Hi Lee,
this is very kind of you. :thumbsup:
I have 2 qeuestions for you:
1) Some set up guide line for TRF201 on dirt hard packed low traction tracks.
2) Next year i'd like to go nitro and since i'm "Tamiya only" i'll go for a TRF801x. Any chance that we will see them easily available also here in Europe? Can you give me some advice on were to find car and parts(Europe/UK)?
Some time ago you posted a topic about you as a future TRF distributor for UK and Eu, am i wrong? If not there is any update about this? :drool:
Thanks in advance for your time.
Bye
WWD
:)
201;
Try running the weight i advised above. also some things i have been going well with lately are:
Cutting rear arms 2mm and shortening wheelbase.
running plastic rear hubs in middle hole.
running inside hole on rear tower.
using backward ackerman position
using 25 degree caster blocks
79 spur with 24 tooth pinion
run yellow springs all round and 35 front 30 rear.
1.3 piston rear and 1.4 front.
i hope this helps.
8th - Unsure the best place to buy? maybe just direct from USA? unfortunately i cannot sell anything in europe.
:(
Lee
Lee Martin
07-07-2011, 08:42 PM
You've already taken the UK national series with 4 straight wins with the 511 so for the sake of all the people who bought the 502 it would be nice to see you run it for the 2 remaining meetings.. I think it would help us all out with set ups etc.. Thanks:thumbsup:
Not for Ozwastry, as the worlds is next week i dont want to upset my 511.
but for southport...who knows ;)
Lee Martin
07-07-2011, 08:43 PM
I don't even run a Tamiya, but :thumbsup: to Mr Martin for putting himself forward to help on here. Good example to other sponsored drivers !
Thanks
Its just nice to be able to try to help people as much as possible... were not as big, bad and ugly as we may seem ;)
maybe you should run Tamiya :p
AndyG
07-07-2011, 08:52 PM
Thanks
Its just nice to be able to try to help people as much as possible... were not as big, bad and ugly as we may seem ;)
maybe you should run Tamiya :p
Thank you for your kind offer of sponsorship, I accept :p
Lee Martin
07-07-2011, 08:54 PM
haha!
if only it was that easy ;)
Rich D
07-07-2011, 09:06 PM
im going to start with 19/91 standard ESC settings.
;)
Thanks Lee, im on 19/89 already so i`ll give it a whirl :) See you tomorrow.
Shifta
07-07-2011, 09:10 PM
Not for Ozwastry, as the worlds is next week i dont want to upset my 511.
but for southport...who knows ;)
Sweet :thumbsup:
Good luck at The Worlds
mikeyscott
07-07-2011, 09:34 PM
Just want to say good luck Lee at the worlds :)
dimblum
08-07-2011, 12:12 AM
Lee,
First of all. Thanks for offering to help us with our setups and general questions.. I don't know of any other sponsored racers who do this on open forums.. Your help is very appreciated.
I've been racing Tamiya for several years now. I currently run a 501X and my friend runs a 511X. We have been having trouble with the front arms breaking too often. It mostly happens on off-road tracks with extreme jumps, but has also happened on smoother indoor clay tracks..
I tried to work around the problem by using stiffer springs in the front and slightly heavier oil.. It helped a little, but I know this is not the best way to go..
What do you do to help your car survive extreme jumps without damaging the front arms?
To note: I have tried DB-01 arms, stock 501X arms, and the more recent lower profile racing arms. The lower profile arms break the easiest. Unfortunately the thicker DB-01 and 501X arms still break too - but they sure do take more of a beating before they do..
Thanks.
jimmy
08-07-2011, 12:29 AM
Im going to be trying 110%. Fingers crossed for me!
Good luck mate - I'll be there to capture the moment
BloodClod
08-07-2011, 01:28 AM
Weights, recently i have been putting weights in and around the rear gear box, this has helps to increase rear traction quite a lot.
normally i use weights to stop the car grip rolling, settle it through bumps or to stop wheeling..... on dirt i normally run a light car with the weight (apprx 30g) under the rear U plate and in front of gear box, and also a small amount up front. (20-30) to stop wheeling.
Lee
Thanks for the tips Lee. I'll be squeezing some time soon to try your suggestions out at the local track.
I noticed that in some of your setups you run a heavier car (70g under servo + weight under the battery), is that a suggested starting point for higher grip surfaces?
Where I run the 201s seem to struggle with:
1) rear grip esp out of corners to line up for the big jumps. I think adding the weight you suggested should help.
2) nose-lifting off the big jumps - in such cases even braking hard doesn't seem to do much to correct the car. I'm just worried if the rear weight will make this problem worse. Any thoughts?
Thanks again for your help - and good luck for the Worlds!
Lee Martin
08-07-2011, 09:38 AM
Lee,
First of all. Thanks for offering to help us with our setups and general questions.. I don't know of any other sponsored racers who do this on open forums.. Your help is very appreciated.
I've been racing Tamiya for several years now. I currently run a 501X and my friend runs a 511X. We have been having trouble with the front arms breaking too often. It mostly happens on off-road tracks with extreme jumps, but has also happened on smoother indoor clay tracks..
I tried to work around the problem by using stiffer springs in the front and slightly heavier oil.. It helped a little, but I know this is not the best way to go..
What do you do to help your car survive extreme jumps without damaging the front arms?
To note: I have tried DB-01 arms, stock 501X arms, and the more recent lower profile racing arms. The lower profile arms break the easiest. Unfortunately the thicker DB-01 and 501X arms still break too - but they sure do take more of a beating before they do..
Thanks.
Hi,
If your breaking the 501X HD arms then im unsure how you could find anything stronger... maybe after each run just check for cracks in the arms, as they could be cracking without you realizing then breaking on the next run.
apart from this, there is not much you can do? continue to run the 501X HD arms and try not to get the big jump wrong and land on one side of the car, try to land flat and level.
lee
Lee Martin
08-07-2011, 09:39 AM
Thanks for the tips Lee. I'll be squeezing some time soon to try your suggestions out at the local track.
I noticed that in some of your setups you run a heavier car (70g under servo + weight under the battery), is that a suggested starting point for higher grip surfaces?
Where I run the 201s seem to struggle with:
1) rear grip esp out of corners to line up for the big jumps. I think adding the weight you suggested should help.
2) nose-lifting off the big jumps - in such cases even braking hard doesn't seem to do much to correct the car. I'm just worried if the rear weight will make this problem worse. Any thoughts?
Thanks again for your help - and good luck for the Worlds!
Which tires do you run?
the shorter wheel base and weight will help the rear.
weight up front will help jumping.
maybe also try a front wing?
Lee
Lee Martin
08-07-2011, 09:40 AM
Good luck mate - I'll be there to capture the moment
:thumbsup::thumbsup::thumbsup:
JustARcFan
08-07-2011, 11:12 AM
Your Kampenhout TRF201 set up would be most appreciated!
Car looked dialed :thumbsup:
AaronR
09-07-2011, 02:14 AM
Plastic rear hubs at the Belgium GP race, Lee?
Best of luck at the Worlds in a couple weeks!
Chris
09-07-2011, 10:29 AM
Lee,
Some TRF201 questions:
Do you run the battery in front or rear?
Which chassis do you use? (stock or the optional)
Same question for the front arms?
Chris
Mouton
09-07-2011, 01:15 PM
Hello Lee, I too must join the choir that sings your praise for giving so much advice to us less experienced! It is much appreciated!
I have a question about the TRF511, what front shock tower do you use? I have managed to write off a couple of stock towers (edges wet sanded and CA glued). I know about Tech Racing, but I have only managed to find their rear 4mm shock towers and they have discontinued all 511 parts. Fibre Lyte makes a 4 mm tower, but I would prefer something that is easier to find. Is there perhaps a Tamiya part in the pipeline?
Best of luck to you and the rest of the team in Finland!
Thanks,
Andreas
Lee Martin
11-07-2011, 09:33 PM
Plastic rear hubs at the Belgium GP race, Lee?
Best of luck at the Worlds in a couple weeks!
Yeh, i have found them to be working well!!! more rear traction
Lee Martin
11-07-2011, 09:34 PM
Lee,
Some TRF201 questions:
Do you run the battery in front or rear?
Which chassis do you use? (stock or the optional)
Same question for the front arms?
Chris
Batteries in the rear,
i use Optional chassis
Standard arms
Lee Martin
11-07-2011, 09:35 PM
Hello Lee, I too must join the choir that sings your praise for giving so much advice to us less experienced! It is much appreciated!
I have a question about the TRF511, what front shock tower do you use? I have managed to write off a couple of stock towers (edges wet sanded and CA glued). I know about Tech Racing, but I have only managed to find their rear 4mm shock towers and they have discontinued all 511 parts. Fibre Lyte makes a 4 mm tower, but I would prefer something that is easier to find. Is there perhaps a Tamiya part in the pipeline?
Best of luck to you and the rest of the team in Finland!
Thanks,
Andreas
i use the standard ones, and i have broken a couple of them over time. the gluing with not help to make them stronger, its basically something needed to break, so the carbon does rather than the alloy.
you can try the 4mm ones.. it will be stronger of course.
Maybe Fredrik could make something up?
Lee
mattybucks
11-07-2011, 09:40 PM
Hi Lee,
Are you using any new parts on your 511 in preparation for the worlds.
Thanks
Matt
Lee Martin
11-07-2011, 09:41 PM
nothing major...
but have a couple of things to try out...
one proto part which i used at the warm up, but have not used it since ;)
rich_cree
11-07-2011, 10:20 PM
Hi Lee, have you had a chance to test out the new range of GHD straighteners yet or will you be sticking with the old tried and tested Gold series for the upcoming worlds?
;)
Mouton
11-07-2011, 10:32 PM
I will keep using the stock towers untill Fredrik runs out of his stash of Tech Racing towers and is forced to make something up. :lol:
Thanks
Andreas
stefka
12-07-2011, 05:37 AM
Hallo Lee !
Excellent thread- your my 201 hero !:thumbsup:
As my car is brilliant already, hereīs my only question :
What is the X (TRF 201X) thatīs always mentioned in the race reports ?:confused:
Is there such a thing ? Is it your speed secret ? Can I buy it ?:D
All the best for the Worlds !
cheers, Stefan
Fredrik Emilsson
12-07-2011, 09:45 AM
I will keep using the stock towers untill Fredrik runs out of his stash of Tech Racing towers and is forced to make something up. :lol:
Thing is that I never break anything. Never have time to drive...:lol:
Drawing a new front and rear shock tower. Will (hopefully) be stronger than original part.:)
F1END
12-07-2011, 10:42 AM
I have a question for Lee.
Do you have any influence at Tamiya in actually getting some 511's out there to buy. No-one seems to ever have any in stock (even overseas) and people seem to always be asking about them. I can't afford one now, but want to buy one soon.
Whenever there is a thread about "which 4wd should I buy?", it's always Durango/B44.1/Cat, probably 'cos no-one wants to recommend a car no-one can find.
I'm sure there would be a lot more 511 drivers out there if there were more cars to drive ;)
P.S. Good luck with the Worlds
GRIFF55
12-07-2011, 12:54 PM
Hi Lee, have you had a chance to test out the new range of GHD straighteners yet or will you be sticking with the old tried and tested Gold series for the upcoming worlds?
;)
hahaaaha, awesome!
Batteries in the rear,
i use Optional chassis
Standard arms
Hi Lee,
Just wondered why you use the standard arms on the TRF201 (part no. 51411) rather than the 'reinforced' front arms (part no. 54265)?
And what difference have you found between the standard and optional chassis?
Ta very much,
Nige
PS - as mentioned in a previous post, when you've got a spare five minutes could you please post up your Kampenhout set up on www.trfracing.com (http://www.trfracing.com) :thumbsup:
Ritchie T
12-07-2011, 02:58 PM
Kidderminster national setup pleaseee
Also ive been speakin with your friend Rounde, he said you guys use kyosho o ring that have a kind of groove in them?
Chris
12-07-2011, 05:40 PM
Thing is that I never break anything. Never have time to drive...:lol:
Drawing a new front and rear shock tower. Will (hopefully) be stronger than original part.:)
Please make them the same as the TRF502X towers. The have one hole less and make them stronger. The outside hole is never used (by most of the racers i think).
fastinfastout
12-07-2011, 06:28 PM
what is the difference between the following 2 arms
51449, standard 201x arms, but can be used on 511
51279, standard 501x arms
compared to the 511 high traction arms, besides being lighter and more flexible?
and why would you want to use 201x rear arms on the 511, they fit according to the 51449 description.
Jamie.T
12-07-2011, 10:06 PM
Your not alone with confusion regarding arms.
As for front arms, there's high traction (54141), super soft (54283) and the 501 extra-thick arms (51275).
On the rear, you have high traction rear arms (54142), then you have the softer rear arms (51449) followed by the extra thick arms (51279)
Hope this helps.
DaveG28
12-07-2011, 11:37 PM
I've tried all the arms over time and my none scientific findings have basically been for the arms Jamie mentioned:
Front
51275 = Strongest arm, but when they fail they clean break (eg end of race), and tend to bend the hinge pin with them
54141 = Crack quite easily, but on the plus side tend not to fail completely, so you finish the race! I've also never bent a hinge pin while running them (so far!)
54283 = Don't crack as often as 54141, but like the front 201 arm I have found they bend and twist, so need keeping an eye on as they knock the geometry out!
Rear
51279 = as per 51275
54142 = as per 54141
51449 = per 54283, except I haven't yet found a twisting problem with them. It's also worth noting this arm has a cut out that's required by the 201, which I don't always see on the other rear arm options, so I'd always go for 51449 for the 2wd!!
muratti
13-07-2011, 04:46 AM
I've tried all the arms over time and my none scientific findings have basically been for the arms Jamie mentioned:
Front
51275 = Strongest arm, but when they fail they clean break (eg end of race), and tend to bend the hinge pin with them
54141 = Crack quite easily, but on the plus side tend not to fail completely, so you finish the race! I've also never bent a hinge pin while running them (so far!)
54283 = Don't crack as often as 54141, but like the front 201 arm I have found they bend and twist, so need keeping an eye on as they knock the geometry out!
Rear
51279 = as per 51275
54142 = as per 54141
51449 = per 54283, except I haven't yet found a twisting problem with them. It's also worth noting this arm has a cut out that's required by the 201, which I don't always see on the other rear arm options, so I'd always go for 51449 for the 2wd!!
I agree with you , Dave, only both you and Jamie forgot about the standard DB01 arms which are 51311 for the front and 51313 for the Rear. Have exactly the same geometry and thickness like the 501 arms but are way softer, nevertheless they tend to bend the hinge pin too just like the 501 arms BUT they cost nearly half of the 501X arms thatīs why i always use them on my 4WDs.
Dave, what cut out do the 51449 have for 2WD? Never realized that!
Fredrik Emilsson
13-07-2011, 08:17 AM
Please make them the same as the TRF502X towers. The have one hole less and make them stronger. The outside hole is never used (by most of the racers i think).
Just my thought. Will also make some other "adjustments".:)
DaveG28
13-07-2011, 12:17 PM
I agree with you , Dave, only both you and Jamie forgot about the standard DB01 arms which are 51311 for the front and 51313 for the Rear. Have exactly the same geometry and thickness like the 501 arms but are way softer, nevertheless they tend to bend the hinge pin too just like the 501 arms BUT they cost nearly half of the 501X arms thatīs why i always use them on my 4WDs.
Dave, what cut out do the 51449 have for 2WD? Never realized that!
There's a cutout on the inner part of the wishbone to stop it fouling the outdrive under compression! I have seen some 4wd high traction arms with them, and some without, so I just buy the 51449 now!
wildwillydriver
13-07-2011, 01:35 PM
201;
Try running the weight i advised above. also some things i have been going well with lately are:
Cutting rear arms 2mm and shortening wheelbase.
running plastic rear hubs in middle hole.
running inside hole on rear tower.
using backward ackerman position
using 25 degree caster blocks
79 spur with 24 tooth pinion
run yellow springs all round and 35 front 30 rear.
1.3 piston rear and 1.4 front.
i hope this helps.
8th - Unsure the best place to buy? maybe just direct from USA? unfortunately i cannot sell anything in europe.
:(
Lee
Hey Lee,
one more time thanks for your effort, it's precious! :thumbsup:
I know your time is short and i promise this is my last post for you.... :)
On 201 i need a couple more info:
1) Cutting rear arms 2mm and shortening wheelbase: I don't understand this copletely.... sorry but my english is not that good.....
2) Would you adivise to use the OPT chassis (high traction) on Dirt dry and low traction tracks?
Now on the 8th:
1) We will see some Set Up sheets on "your" TRF site?
2) If not, can you give some set up guide lines for Dirt dry and low traction conditon?
Thanks in advance.
Bye
WWD
:)
jayfinn8
24-12-2011, 01:48 PM
Very happy one at that. Already like better than my DEX410 v3.
Is anyone running big bore shocks and which one's. The rears need rebuilding so just trying to decide to rebuild or by a different set of shocks. Also what rear hub do most run 0,.5, or 1 degree. Is everyone still running pin set up in axle for wheel or can I fit 12mm hexes, what brand? Thanks....
Rich D
24-12-2011, 05:05 PM
Very happy one at that. Already like better than my DEX410 v3.
Is anyone running big bore shocks and which one's. The rears need rebuilding so just trying to decide to rebuild or by a different set of shocks. Also what rear hub do most run 0,.5, or 1 degree. Is everyone still running pin set up in axle for wheel or can I fit 12mm hexes, what brand? Thanks....
Most run the std shocks albiet with the better looking HL gold cylinders. Not seen any 511 with big bores fitted personally.
Rear hubs, my settings are - zero degree on high grip dry astro, 0 or 0.5 indoors and 1.0 in the wet.
Std pin setup at the back. Std Tamiya wheels or Losi rims fit without modification.
HTH
Lee Martin
26-12-2011, 12:05 AM
As rich says really.
Use pin.
No big bores, the TRF shocks work really good.aune try some different springs?
Lee
kedal
26-12-2011, 11:06 AM
Lee, what are those yellow spring you use In Pau during Euro ? From another brand ? Kyosho ones ? If yes, why using these insteed of the Tamiya ones ?
Thanks :)
mattybucks
26-12-2011, 11:56 AM
Lee, what are those yellow spring you use In Pau during Euro ? From another brand ? Kyosho ones ? If yes, why using these insteed of the Tamiya ones ?
Thanks :)
They are Kyosho springs, I now use them on my 511. The tamiya springs needed to be cut down.
kedal
26-12-2011, 05:38 PM
Ok, thanks. I'm happy for now with the stock spring, so, I think just play with the oil for my local track.
Aussie Top Force
03-01-2012, 09:49 AM
This is a really helpful thread! Thumbs up to Lee for offering his knowledge.:thumbsup:
I haven't raced since the mid 1990's, but a recently ordered a TRF 201 (Limited Edition) from HK, nowhere to be found in Australia I'm affraid! I'm looking forward to racing the car as is out of box and then progressively trying the modifications Lee has suggested. Most tracks I'll be running on will be hard packed clay and outdoors. Grip will be a matter of how much 'Aussie' dust there is. I'll be starting of in a Stock Class 17.5 turn Brushlesh.
A question: Lee any tips on building the TRF 201 out of the box? Should I be installing upgraded ball studs from scratch as I have been reading that the standard versions break or bend easily? Any other items to replace to make the car as bullet proof as possible?
Regards
David
Lee Martin
04-01-2012, 06:11 PM
David,
The 201 is very good out of the box in terms of quality. You can look into Ceramic diff balls and also spring options.
Things to try - LMR Bulkhead for 201 - adding 35g of weight to front to make better at jumping and on bumpy tracks to keep the noise down!
The car is very strong also! you can try the 501X HD rear arms if you ever break a standard one? these are super strong!!!
Another nice touch is the Rudebits carbon battery strap! ;)
Hope this helps.
Lee
Jamesk
05-01-2012, 10:00 AM
A question on the 201, i seem to have a large of amount of bump steer on a very bumpy track i race on. I can not tell if its more front or rear but it seams worse on full throttle but i have plenty of traction. An advice would be appreciated.
jK
steve-thebabystore
05-01-2012, 12:50 PM
Hi Lee, slightly off topic but congrats on your new arrival.
Aussie Top Force
06-01-2012, 12:42 AM
David,
The 201 is very good out of the box in terms of quality. You can look into Ceramic diff balls and also spring options.
Things to try - LMR Bulkhead for 201 - adding 35g of weight to front to make better at jumping and on bumpy tracks to keep the noise down!
The car is very strong also! you can try the 501X HD rear arms if you ever break a standard one? these are super strong!!!
Another nice touch is the Rudebits carbon battery strap! ;)
Hope this helps.
Lee
Hi Lee,
Thanks for those tips! I've been looking on the JT models and RC Domination website and cannot find the "LMR Bulkhead for 201". Are you able to help point to where I could order it from? Thanks for your time!:)
mattybucks
06-01-2012, 12:57 AM
Hi Lee,
Thanks for those tips! I've been looking on the JT models and RC Domination website and cannot find the "LMR Bulkhead for 201". Are you able to help point to where I could order it from? Thanks for your time!:)
The bulkheads are only just out. You can order one directly from Lee http://l-m-racing.co.uk/?page_id=266
Lee Martin
07-01-2012, 12:06 PM
A question on the 201, i seem to have a large of amount of bump steer on a very bumpy track i race on. I can not tell if its more front or rear but it seams worse on full throttle but i have plenty of traction. An advice would be appreciated.
jK
How do you mean?
Bump steer is the amount of steering change the front wheel receives from suspension movements? is this what your asking?
or are you saying your car is bad on bumpy tracks?
Lee
CraigM
08-01-2012, 03:18 AM
Hi Lee,
What is a good starting point for oil in front and rear gear diffs? I'll be racing on a med grip hard packed dirt track
Thanks
Craig
Aussie Top Force
10-01-2012, 08:39 AM
The bulkheads are only just out. You can order one directly from Lee http://l-m-racing.co.uk/?page_id=266
Thanks! I'll investigate more once my TRF 201 arrives. Hopefully this week!:confused:
Jamesk
10-01-2012, 08:47 AM
Lee,
The front end is very hard to keep in a straightline on bumpy tracks, ive read your reveiw in on of the rc mags and seen you raise the front sterring arm's, ill fit the spacers and see if thats the answer.
Thanks
jK
Lee Martin
10-01-2012, 12:43 PM
i have not had much chance to test gear diffs....
try 10 front
5 rear.
Lee
Netmav
18-01-2012, 10:06 AM
Hi Lee.
Congratulations on the Area51 4WD win! NICE! :thumbsup:
I would like to ask you a favour, if you don't mind?
We're having a hard time finding spare A-parts (Gearbox tree) for the 502x, so I was wondering if you could talk to someone at Tamiya, and ask them about this?
Why isn't it possible to get essential spare parts for the 502x?
Or maybe you know something about this already?
I know this is a long shot, but we're getting a little desperate here in Norway now, as the first race of the Nationals cup is in a few weeks.. :eh?:
Thanks mate.
Keep up the good work!
BR,
Martin Stensland
NORWAY
dobber
18-01-2012, 11:36 AM
502x question.
Im struggling with ride height. I see your setup for taplow was 18mm. Currently mine is sitting at about 26mm. How do i get it lower and sit near that illusive 18mm.
Question about diffs too. How tight do you set them and is there any deffinative way of setting them up. I think that my diffs are too tight but as i have no reference point to work from im kind of stuck. I slackened off my rear diff just a tad the other week and it made the rear of the car spin round when cornering. Any tips of hintrs on these two would be great.
Cheers.
Even better than that why not pop along to Surrey & Hants Radio Controlled Car Club one thursday night ;):thumbsup:
Lee Martin
18-01-2012, 07:40 PM
502x question.
Im struggling with ride height. I see your setup for taplow was 18mm. Currently mine is sitting at about 26mm. How do i get it lower and sit near that illusive 18mm.
Question about diffs too. How tight do you set them and is there any deffinative way of setting them up. I think that my diffs are too tight but as i have no reference point to work from im kind of stuck. I slackened off my rear diff just a tad the other week and it made the rear of the car spin round when cornering. Any tips of hintrs on these two would be great.
Cheers.
Even better than that why not pop along to Surrey & Hants Radio Controlled Car Club one thursday night ;):thumbsup:
I will try to pop along soon!
ride height...well your car could be running very light? i have aruond 60g of rudebits in the back of mine.
You will also need to cut the rear spring down to get the required height. Take 2 coils off it.
Then you should be fine!
Diff tightness.... its difficult to explain, i will do a video soon, just make sure the front is tighter than the rear and neither are slipping!
Lee
Rich D
18-01-2012, 09:40 PM
502x question.
Im struggling with ride height. I see your setup for taplow was 18mm. Currently mine is sitting at about 26mm. How do i get it lower and sit near that illusive 18mm.
Question about diffs too. How tight do you set them and is there any deffinative way of setting them up. I think that my diffs are too tight but as i have no reference point to work from im kind of stuck. I slackened off my rear diff just a tad the other week and it made the rear of the car spin round when cornering. Any tips of hintrs on these two would be great.
Cheers.
Even better than that why not pop along to Surrey & Hants Radio Controlled Car Club one thursday night ;):thumbsup:
To set the diffs, this is my method.......
Car facing away from you, hold left rear wheel with left hand. Hold spur gear with left thumb. Turn right rear wheel forward slowly at first still holding the left rear wheel and jamming the spur. You should see the slipper plates turning. If they arent then either your diff is too slack or your slipper is set too tight.
Its a balance that you`ll get a feel for. When its set right, then the diff action should be smooth but it shouldnt slip when you test it on the bench.
For the front, just face the car nose towards you and repeat the method above. I try turning the right wheel slowly at first until im happy that it`s not slipping. Once its somewhere near, i turn it more quickly, kind of "jerk" - this is more like the motor would turn the transmission. If you hear it slip, just tighten it 1/8 of a turn further.
As Lee said, set the front so that the diff action is a fraction tighter than the rear.
Im sure he`ll correct me if im talking crap but this is how i set my 511 diffs. I only have to rebuild them a couple of times a season. I think that those who say their tamiya diffs didnt last before becoming gritty must be either running them a little too loose, setting the slipper too tight, or not using diff covers to stop the dirt. Another good tip is to use a shock foam compensator within the outdrive to prevent dirt from getting into the thrust race.
Rememeber black grease for the thrust race and clear silicone grease for the diff balls/plates.
HTH
MHeadling
18-01-2012, 09:48 PM
Lee I noticed the springs on your cars are black from the Area51 meeting, are these still Tamiya springs or a different brand?
Did you paint of dye them if they are the Tamiya ones?
Looks cool btw!
msxmre
19-01-2012, 08:00 AM
Mark I think in Jimmys report he mentions that the springs are X Gear springs or something along those lines. Check the 4wd coverage of Area 51.
Scotty....
MHeadling
19-01-2012, 09:41 AM
Oh ok cheers Scotty, I'll have a read.........
jimmy
19-01-2012, 10:24 AM
http://www.xgear.jp/
Chris
19-01-2012, 05:36 PM
http://www.xgear.jp/
Which spring rate? (F/R)
5ohTwoX
20-01-2012, 06:22 AM
Lee did you leave Tamiya? I just read u signed with Mugen Seiki, congratulations on your new sponsership but it will be sad to see you leave as well.
He's staying with Tamiya for 10th.
http://www.neobuggy.net/modules/news/
5ohTwoX
20-01-2012, 10:27 AM
Oh ok, that's a relief! :thumbsup: Thanks for clearing that up.
dobber
20-01-2012, 10:31 AM
Cheers for the reply Lee. I'll give a few bit a try for next week. Would be good to see your diff setup guide when done :)
Thanks Rich D for the guide on diffs too :)
I will try to pop along soon!
ride height...well your car could be running very light? i have aruond 60g of rudebits in the back of mine.
You will also need to cut the rear spring down to get the required height. Take 2 coils off it.
Then you should be fine!
Diff tightness.... its difficult to explain, i will do a video soon, just make sure the front is tighter than the rear and neither are slipping!
Lee
DavidAMS
27-01-2012, 10:20 PM
To set the diffs, this is my method.......
Car facing away from you, hold left rear wheel with left hand. Hold spur gear with left thumb. Turn right rear wheel forward slowly at first still holding the left rear wheel and jamming the spur. You should see the slipper plates turning. If they arent then either your diff is too slack or your slipper is set too tight.
Its a balance that you`ll get a feel for. When its set right, then the diff action should be smooth but it shouldnt slip when you test it on the bench.
For the front, just face the car nose towards you and repeat the method above. I try turning the right wheel slowly at first until im happy that it`s not slipping. Once its somewhere near, i turn it more quickly, kind of "jerk" - this is more like the motor would turn the transmission. If you hear it slip, just tighten it 1/8 of a turn further.
As Lee said, set the front so that the diff action is a fraction tighter than the rear.
Im sure he`ll correct me if im talking crap but this is how i set my 511 diffs. I only have to rebuild them a couple of times a season. I think that those who say their tamiya diffs didnt last before becoming gritty must be either running them a little too loose, setting the slipper too tight, or not using diff covers to stop the dirt. Another good tip is to use a shock foam compensator within the outdrive to prevent dirt from getting into the thrust race.
Rememeber black grease for the thrust race and clear silicone grease for the diff balls/plates.
HTH
awesome tip for setting the diff, tried it and it works great, no more slipping diffs for me!
thanks Rich
@ dobber i use 5mm limiters in the rear shocks with 2 coils cut to get the height to 18mm
using 5400 60c ip saddles with no weight.
guinness
28-01-2012, 01:18 AM
Lee i just watch ur video interview at neobuggy ,nice to see u staying with the tamiya 1/10 cars.
you give me some tips about my 201 on ur last visit to Taplow RC,are u coming back any time soon? as i want pick your brain again due to the fact that the 201 is getting on my nerves ( don't want really switch brand ) because the car is pushing all the time on/off power.
thanx
spud31
28-01-2012, 12:05 PM
Are u running the under servo weight 85g , as that transformed my 201 an stopped it pushing.
Rich D
28-01-2012, 12:18 PM
Thanks Rich D for the guide on diffs too :)
awesome tip for setting the diff, tried it and it works great, no more slipping diffs for me!
thanks Rich
Happy to help :)
guinness
28-01-2012, 12:32 PM
Are u running the under servo weight 85g , as that transformed my 201 an stopped it pushing.
Im using the 72g under servo weigh.
This is my setup
http://db.tt/uSf8RbFH
spud31
28-01-2012, 01:08 PM
i would put the standard rear uprights on to reduce the toe.
In position 1 put a 10 gram weight to help the iniital steering.
http://www.trfracing.co.uk/page_1265126433672.html this is lees setup from taplow.
He runs a shorter front link than you to give more steering, id also try front pins ior if there too much yellow mini spikes rather than normal staggers.
Cut staggers may also work
guinness
30-01-2012, 02:58 AM
i would put the standard rear uprights on to reduce the toe.
In position 1 put a 10 gram weight to help the iniital steering.
http://www.trfracing.co.uk/page_1265126433672.html this is lees setup from taplow.
He runs a shorter front link than you to give more steering, id also try front pins ior if there too much yellow mini spikes rather than normal staggers.
Cut staggers may also work
anything other then staggers make the car to twitchy . mini spikes will try them!
i will try the 10gm in position one and 25degrease C hubs and see how it goes !
Hi Lee,
Could you post up a Vega TRF201 setup when you get a chance.
Also what extra bits are required on top of the TRF201 kit?
Thanks
Rob
Rich D
10-02-2012, 05:36 PM
Hi Lee,
Could you post up a Vega TRF201 setup when you get a chance.
Thanks
Rob
Lees 201 setups .......
http://trfracing.co.uk/page_1265126433672.html
Hi Lee,
Also what extra bits are required on top of the TRF201 kit?
Thanks
Rob
Option parts for the 201 can be found here ....
http://trfracing.co.uk/page_1266421668280.html
Lees 201 setups .......
http://trfracing.co.uk/page_1265126433672.html
Option parts for the 201 can be found here ....
http://trfracing.co.uk/page_1266421668280.html
I think he was talking about the VEGA 201 conversion, not regular TRF201 setups / option parts...
Rich D
10-02-2012, 07:17 PM
I think he was talking about the VEGA 201 conversion, not regular TRF201 setups / option parts...
:blush:, must learn to read !
guinness
19-02-2012, 08:29 PM
Any luck with the Vega setup ?
clint
29-02-2012, 04:42 PM
Hi Lee was curious if you could give a decent starting set up for A Vega 201 V2 for a tight carpet track? thanks
Aussie Top Force
08-03-2012, 09:57 AM
Hi Lee,
I just noted the Rude bits post for the Camber mounts you're using on the 502X:
http://www.oople.com/forums/showthread.php?t=95536
One of the pictures is a close up shot looking at the back of the front shock tower. It appears that you are using a 'wedge' or 'spacer' between the shock tower and mount place on the gear box cover. This 'wedge' would serve to move the front tower forward, further does it contain an angle so it lays the shock tower back at the same rake angle as the front suspension arms?
If so it would seem you have solved an issue that has been raised elsewhere on these forums.
The reason I ask is that I'm comtemplating buying either a 502X or 511x. Here in Australia the 502X looks the most sane choice as the diffs are sealed and our tracks are mostly outdoor and dusty, however I have been hesitant as there has been much discussion around the problems of the front end geometry of the 502x compared to the 511x.
The Australain National titles are on here in Sydney in early April, would be cool to see you here. I don't know if a Tamiya has taken a major title in Australia ever?
Cheers
Lee Martin
15-03-2012, 10:29 PM
Right,
Hi guys, its been a while since i looked on here as i have been moving house and all sorts, so.......
you will find a starter set up on LMR website ( www.l-m-racing.co.uk (http://www.l-m-racing.co.uk) ) for the 201 vegaV2, soon i will put my EOS set up online.
David:
this is just a spacer, but people have made a wedge....i find the spacer works well enough for me. i think you need to move it in total about 5mm to make it free up! ;)
Also look for the new LMR/Rudebits camber link mods! these are available now... just not on my website yet, email me if interested!
Lee
Aussie Top Force
23-04-2012, 09:16 AM
Hi Lee,
Congratualtions on your recent successes with both cars and the Vega 201!
I'm in two minds about which one to purchase to run along side my 201! What are the underlying decisions you make to decide whether to use the 502 or 511.
This might be obvious, but what battery hold-down nuts are you using here? Thanks!
http://rcdevil.smugmug.com/2012/EUROS-RC-2012-DAY-1-2/i-FWhSLLF/0/M/IMG4124-M.jpg
Cobra
24-07-2012, 10:38 AM
Hi Lee,
Looking at the setup for the Vega you have been using MR oils in the shocks,
what is the equivalent for Losi oil please?
cheers
Ken
This might be obvious, but what battery hold-down nuts are you using here? Thanks!
http://rcdevil.smugmug.com/2012/EUROS-RC-2012-DAY-1-2/i-FWhSLLF/0/M/IMG4124-M.jpgCan anyone help me identify these thumb screws? Thanks! :thumbsup:
stevenich
16-08-2012, 03:03 PM
Lee,
I have noticed you use everything from Tamiya blue to Kyosho Big bore and regular Kyosho springs.
What do you recommend for the high traction US clay tracks? I did notice the Tamiya springs tend to rub the bodies.
Should I just purchase the Tamiya spring kit F/R and the Kyosho RB5 yellow/red/blue F/R and go play?
Lee Martin
20-08-2012, 10:46 AM
To be honest, as you say i have tried most springs now and the TRF ones still feel like one of the best...
The X gear springs are good on the 4wd, but i prefer the TRF springs on the 201
;)
Blue rear - Black front
Lee Martin
20-08-2012, 10:47 AM
Those are TRF thumb screws.
stevenich
20-08-2012, 09:07 PM
I ordered a few sets of the X-Gear XSB to try out.
rcaddict
02-09-2012, 02:38 AM
Lee prefers his 511 but he wont publicly admit it because Tamiya stopped making 511 kits and still has to sell whatever 502 kits are left. 502 is still very good but I think AE has the best overall 4WD shaft 1/10 buggy design at the moment. 511 is tops! :thumbsup:
Maybe Tamiya will come out with the next generation belt driven 1/10 TRF buggy to continue in the 511's footsteps, but who knows? Actually, Lee would probably know. But with the introduction of the DB02 it doesnt look as such. I'm holding on to my 511 until spares are no longer available.
Aussie Top Force
02-09-2012, 08:12 AM
I finally purchased a 502X from Japan. The store still a 511, one of each in fact! I purchased their last 502X. It came down to maintenance. The 502 presented less diff rebuilds due to sealed gear boxes. Here in Australia our tracks are all dirt and I'd been there and done that with belts in Yokomo's in the 1990's.
If I had the cash I would have ordered the 511X as well and stored it way. I think they'll become a NIB rarity in the near future or built it for display purposes, as it looks like a nice car to build. I enjoy building new kits just as much as racing them!
The 502X:http://www.tamiyaclub.com/showroom_model.asp?cid=115790&sid=33946
Any 502X tips Lee for hard packed clay with a dusty surface?
P.S. - Loving the LMR wing on my 502X looks better than the TRF version and is a lot tougher!:woot:
Aussie Top Force
02-09-2012, 10:41 AM
Hi Lee,
When you run a 201X in rear motor configuration, what length chassis do you use. I've noted +6mm and +8mm versions amongst various TRF drivers.
Have the team settled on what is best all round? Will TRF release a version for the club racer so we don't have to buy two chassis and start cutting!
rcaddict
02-09-2012, 08:10 PM
I finally purchased a 502X from Japan. The store still a 511, one of each in fact! I purchased their last 502X. It came down to maintenance. The 502 presented less diff rebuilds due to sealed gear boxes. Here in Australia our tracks are all dirt and I'd been there and done that with belts in Yokomo's in the 1990's.
If I had the cash I would have ordered the 511X as well and stored it way. I think they'll become a NIB rarity in the near future or built it for display purposes, as it looks like a nice car to build. I enjoy building new kits just as much as racing them!
The 502X:http://www.tamiyaclub.com/showroom_model.asp?cid=115790&sid=33946
Any 502X tips Lee for hard packed clay with a dusty surface?
P.S. - Loving the LMR wing on my 502X looks better than the TRF version and is a lot tougher!:woot:
You should have bought the 511 instead, and bought some diff covers from Fredrik. Then you would have had the better car and with sealed diffs too. Oh well. Now that you have the 502 enjoy it. 90% of it boils down to the driver and setup anyway so chosing between the two cars is really splitting hairs, but when grip is loose or the track is wet belt drive is the better choice.
Aussie Top Force
03-09-2012, 09:45 AM
You should have bought the 511 instead, and bought some diff covers from Fredrik. Then you would have had the better car and with sealed diffs too. Oh well. Now that you have the 502 enjoy it. 90% of it boils down to the driver and setup anyway so chosing between the two cars is really splitting hairs, but when grip is loose or the track is wet belt drive is the better choice.
With the opposition being B44's, Kyosho's and Durango's the 502X wont be at any disadvantage here on the Australian tracks. All in the same boat with shaft drive. There are not too many Losi 4wd's running in Aus these days. As you say, splitting hairs! Further a wet track here involves mud, lots of mud, to the point where it builds up on tyres. We usually have to close the tracks.
Don't worry, no regrets and I'm already enjoying it!
Those are TRF thumb screws.Thanks! Still haven't been able to find them anywhere.
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.