Tyre removal?

[chris68nufc]

Im sick of buying new rims every time i need new tyres so i have got myself a 5 Litre bottle of nail varnish remover.Forgot the technical name. Are you supposed to just cut the tyres off as much as you can and then soak the wheels? For how long?
Was a nightmare getting this stuff in such big quantities because apparently this stuff was used in the London bombings.

[wacattack]

Cut the main part of the tyre off (leaving the glued bits on) so you can remove the foam inserts. Put them in the ascertone for about 48 hours. It sometimes does it in less time when the tone is newer but Id recommend allowing 48 hours

[chris68nufc]

Nice 1. Accetone. Thats the fella! How much do people normally pay for this stuff?

[jim76]

pure acetone can be purchased from fibreglass producers for about £5 per gallon. needs special delivery due to flammable nature which usually costs £10. So £15 delivered per gallon.

pure acetone also works much quicker than diluted nail varnish.

i think a few model shops stock acetone, or a few individulas on here may sell it. they will no doubt post details for you

[David Church]

I get acetone from a car paint & body supply shop, about £10 per 5 litre's.
Check the yellow pages.

[neiloliver]

...or ebay for £20 delivered (5 litres). I put mine in an old 5 litre emulsion paint tin (well cleaned first). Then you can put the lid on tight and stop the damn stuff evaporating. I leave for 24 hrs, then pull the tyre bead off, then leave for a further 24hrs to get the rest of the adhesive off. The scrub in soapy water to get them nice and clean ready for more tyres....

N

[mobile chicane]

yep pure acetone is what I use dont even need to cut the tyres off just soak and voila of they come:woot:

[PaulRotheram]

Or do what i do...

Put your tyres in DC's tent compartment for a night and the vapour from his mouth will de-glue the rims.

Knew that vodka had more uses than one ;):thumbsup:

[niggs98]

rofpmsl either that or all his hot air will melt the glue and tyre off for you :P:P:O

[David Church]

Or do what i do...

Put your tyres in DC's tent compartment for a night and the vapour from his mouth will de-glue the rims.

Knew that vodka had more uses than one ;):thumbsup:


Schhhhhhhhh!!!!! My secret is out!!!!!!!!!!! :thumbsup:

[RogerM]

An alternative method is heat!!!

I have just stripped over 100 pairs of tires of rims (what a fun day that was!!) as the tires were either new or 1 run old but on older car's rims (mainly pred single point drive, Yokomo BC Special, B3 and B4 fronts ...... in case anybody is after wheels for these cars PM me!).

A simple method is to use old baking trays and an oven set to 100deg C. Leave them in there for about 10-15 minutes and they should pull off easily. The really well stuck ones might need to go back in at 120deg C.

Thought it was worth mentioning!!!

[James]

Years ago we bought one of those burco boilers they usually use for tea/coffee making, put a buch of tyres in there and let them simmer.. dont know if the wheels would warp these days but its another option...

[quincey]

just a quick warning about acetone,i work with the stuff and it has to be used in a well ventilated area as it dries your lungs out after a while.
Not nice.

[MK999]

i usually put tyres in a sealed container, guessing that's fine as well? :confused:

[Chequered Flag Racing]

A simple method is to use old baking trays and an oven set to 100deg C. Leave them in there for about 10-15 minutes and they should pull off easily. The really well stuck ones might need to go back in at 120deg C.


Oven works for me to :thumbsup: just don't do it when she's about or the Sunday roasts in :woot:

[josh_smaxx]

I just use the cheap nailvarnish remover from Boots, works a treat in a tubba ware box with those sealable flap things :woot:

[b4rs]

if you are using acetone, make sure you wear goggles, rust me, you get that stuff in your eye, and you are instantly F***d to say the least. it clouds the cornea, and dont breathe it as it causes liver damage. my dad uses it at work and one of his mates is blind in one eye. its nasty stuff if u use it incorrectly.:thumbdown:
but good stuff for what it can do:thumbsup:

[b4rs]

also got any left over? mix it 1 part with 20 parts petrol for improved fuel economy.

[David Church]

yes, open doors and windows, wear gloves as well!!!! I am a painting contractor, so know about this stuff!!!
I have 2 tupperware containers, 1 for the main soak, and 1 cleaner. After the cleaner tub gets a bit manky, I top up the main tub, and put fresh in the clean tub, works a treat, then hot soappy water, and your done. I put the whole wheel with tyre and insert in, then wash all when finished, my half worn tyres go to the newbies and youngesters at EPR!!!!!!! And you can reuse the inserts as well, bit funny how much they expand from the acetone, lol.

[josh_smaxx]

I take the inserts out as they absorb silly amounts of the acetone and im tight :D so i save it.

[bigred5765]

An alternative method is heat!!!

I have just stripped over 100 pairs of tires of rims (what a fun day that was!!) as the tires were either new or 1 run old but on older car's rims (mainly pred single point drive, Yokomo BC Special, B3 and B4 fronts ...... in case anybody is after wheels for these cars PM me!).

A simple method is to use old baking trays and an oven set to 100deg C. Leave them in there for about 10-15 minutes and they should pull off easily. The really well stuck ones might need to go back in at 120deg C.

Thought it was worth mentioning!!!

what do you think cooking plastic at any were near 100 degree,s will do the plastic,the rims made of

[Medders]

Just whack them the steamer with the veg for half an hour and tyres come off no problem. Much better than messing around with chemicals.

[ashleyb4]

ive never seen veg cooked in chemicals before :D:D:lol:

A

[unluckypixie]

An alternative method is heat!!!

A simple method is to use old baking trays and an oven set to 100deg C. Leave them in there for about 10-15 minutes and they should pull off easily. The really well stuck ones might need to go back in at 120deg C.

Thought it was worth mentioning!!!

I've not tried it yet but I was told to boil them. I would have thought boiling would result in a more even temperature compared to an over where they might get crispy on one site! ;)

[jimmy]

FRY THEM:lol:

[Jimbo]

I tried boiling some rims at full boil for half an hour turning regularily, and some glue broke off, but a lot still stayed stuck. So I chucked it into a container of acetone for a couple of hours and viola! Pulled straight off and no glue left on the rims either.

Seems it depends what glue you use. I had in the past baked tyres in the oven at 110* and this worked ok too, but I didn't want to stink out mine again:yawn:

[chris68nufc]

Just remembered that i had my first batch of wheels to check in the garage after i read this post. Took the remaining rubber off with ease. It just fell off. I have got stacks of wheels now to go through the process. Im sure if i remember rightly i have been paying about £15 for tyres(which i still have to!) £3 ish for foams(i know Jez used to sell tyres and foams as a tyre deal) and about £7 for wheels a pair so it loks like a good move to get this acetone stuff even though i had a nightmare getting it.

[nick oliver]

Hi if there is enff intrest i can get it some for 15quid for 5 litres... depending on the intrest..

Nick.

[strobe]

Just removed some tyres of there rims with some Acetone.
Just wondering that some of the Foams that have been removed look like new. Would they be ok to use again or should i bin them.

[David Church]

They will be fine, just wash them in hot soapy water then rinse well. Or some people put them in the washing machine.

[strobe]

Thanks for the info DC. Will give it a go.
Mark

[bigred5765]

as dc said we just rinse ares in hot soapy water and re use em

[Andy 2]

how often should tyres be replaced

[josh_smaxx]

how often should tyres be replaced

When there worn out, im brutal on the throttle so they dont last ages for me but its up to you when you think your loosing to much grip.