PDA

View Full Version : 210 diff help!!


losichris
18-10-2011, 09:07 AM
ok, im on borderline to throwing the car through the window!!
ive followed peoples advice on diff building with the thrust the correct way, and the clip the flat side to the screw etc.
and it still isnt happening....
im out of ideas, and getting very frustrated!!

jkclifford
18-10-2011, 09:13 AM
What's happening exactly?

gainsy
18-10-2011, 09:13 AM
Whats happening to it? does the clip keep coming out?
The flat bit should be away from the screw, so when you put it in the rounded side will go in first

Legacy555
18-10-2011, 09:16 AM
....and the clip the flat side to the screw etc.


Flat side of the circlip should be away from the thrust race, not close to it.

losichris
18-10-2011, 09:18 AM
the clip is in, locked into the outdrive.
the diff works, but its very tight. not only that but its slipping.
and i cant tighten all the way without it stripping

gainsy
18-10-2011, 09:21 AM
How about the nut retainer, is it fully into the outdrive? mine didn't go straight in but with a gentle tap it soon slid straight in, also are you using kit balls or ceramic?

losichris
18-10-2011, 09:32 AM
when the diff is tight, seems to be all the way in.
using kit balls :confused:
think its something on the thrust side

gainsy
18-10-2011, 09:39 AM
Hmmm that's a puzzler :confused:
Stupid question as you probably have but have you put the shim in betwen the bearings?

Northy
18-10-2011, 09:39 AM
[email protected]

T: +44 (0)1530 412352

Contact TD

G

losichris
18-10-2011, 09:41 AM
yeah, gone through it 4 or 5 times. might be an error in the part
will email the support team
cheers guys

gainsy
18-10-2011, 09:43 AM
No probs, hope you get it sorted

gainsy
18-10-2011, 09:46 AM
1 thing i did do was compress the spring a few times with pliers before i fitted it, just to work it in a bit

Big G
18-10-2011, 10:08 AM
a lot of previous manuals I've followed say to compress the spring. I was quite surprised not to see this step in the 210's manual so I didn't compress it

gainsy
18-10-2011, 10:31 AM
a lot of previous manuals I've followed say to compress the spring. I was quite surprised not to see this step in the 210's manual so I didn't compress it

I did it out of habit just like i compressed the slipper spring as well :), like you say the manual didn't mention it but then the manual didn't mention anything about setting the diff up :thumbdown:, for a newbie this must have been very confusing & not everyone has access to this great forum for advice, i have asked durango to include it in the online manual but have not heard back from them about it

mikeyscott
18-10-2011, 10:34 AM
I did it out of habit just like i compressed the slipper spring as well :), like you say the manual didn't mention it but then the manual didn't mention anything about setting the diff up :thumbdown:, for a newbie this must have been very confusing & not everyone has access to this great forum for advice, i have asked durango to include it in the online manual but have not heard back from them about it

Adam said on another post that that they'll be doing some things in their tips section

Origineelreclamebord
18-10-2011, 11:57 AM
Getting the clip inside is a problem in itself. It has been proven many times in the past that using the right tool for the right job makes the difference between failing and succeeding.

So I tried to get a hold of circlip pliers with beaks/pins small enough to fit inside the holes. Guess what? I've been two four or five stores, been riding on me bicycle for two hours, without result! :confused: I tried a DIY shop first, which had circlip pliers, but too large. Then I went to a few specialist stores, and they all didn't have this size available, all for larger circlips, even if they did have the same size of circlip available that's used in the diff!

What's next? Well, I was directed to Fabory, but to buy a tool of 20+ euros for a single circlip seems a little steep for me (that's the lowest price they'll sell it for at Fabory, if they even have it). Therefor, I bought some cheap-o pliers with small, round beaks, and the Dremel will hopefully do the rest. :thumbsup:

stegger
18-10-2011, 12:14 PM
When i had the SX i used to use long nosed tweezers and they worked a treat. Should be ok on this aswell. Will let you know when my kit turns up :yawn:

Legacy555
18-10-2011, 12:37 PM
When i had the SX i used to use long nosed tweezers and they worked a treat. Should be ok on this aswell. Will let you know when my kit turns up :yawn:

Similar to that, I bought a small nail scissors and dremeled the ends slightly to fit the clip

Origineelreclamebord
18-10-2011, 12:38 PM
Problem already solved :thumbsup: Here it is:

http://i65.photobucket.com/albums/h212/Varockshade/DEX210%20Build%20Thread/DSC06538-2.jpg
http://i65.photobucket.com/albums/h212/Varockshade/DEX210%20Build%20Thread/DSC06539-2.jpg

This mod took... 5 minutes? First time I've butchered a tool, but the result is actually better than I expected. 4.95 euros well spent! :D

gainsy
18-10-2011, 01:26 PM
Adam said on another post that that they'll be doing some things in their tips section

That's fair enough Mikey but i still think it should be in the manual as not everyone will look on the web or even be able to get on the web
Just my opinion & they dont have to take it if they dont want to

mikeyscott
18-10-2011, 01:44 PM
That's fair enough Mikey but i still think it should be in the manual as not everyone will look on the web or even be able to get on the web
Just my opinion & they dont have to take it if they dont want to

Raise it with Durango - [email protected] ?

gainsy
18-10-2011, 01:52 PM
Raise it with Durango - [email protected] ?

I did & got no response
Anyway i better stop derailing Chris's thread
Hope you got it sorted Chris

andys
18-10-2011, 03:43 PM
I had EXACTLY the same diff problem.

You can't get your diff right because the clip is buggered, as you tighten the diff the clip is moving, it's not being retained in the groove as it should.

You could try the 'spread' tip that Adam posted, i.e trying to open the clip back up once it's in position.

IMO the clip is a bit crap, mine was replaced with a Schumacher clip and the diff is like night and day now, I think the Schumacher clips must be stronger ?

Good luck.

Origineelreclamebord
18-10-2011, 04:57 PM
I finished building my diff a few hours back, with the 'custom' pliers I posted. I also read through all the advice posted in the various topics (including that of Adam Skelding), and my diff feels both silky smooth and tight enough not to slip :)

I did have one small 'issue', which is that the nut is not very deep into the outdrive. I had a good look at it, and though I haven't made the upper links yet, it seems I can drive the car with a camber angle up to -5 degrees (or even slightly more) without having the driveshaft touch the retaining nut. So not really a problem actually, even though the retaining nut is further inside the outdrive on TD's release pictures.

Bungleaio
18-10-2011, 06:12 PM
I've not run my car yet but I have built it and I used a set of hudy's snap ring pliers to put the cir clip in the diff and they worked a treat.

http://www.hudy.net/xhudy/products/proddesc.php?prod_id=404&kategoria=130

OneKiwi
18-10-2011, 08:01 PM
I had EXACTLY the same diff problem.

You can't get your diff right because the clip is buggered, as you tighten the diff the clip is moving, it's not being retained in the groove as it should.

You could try the 'spread' tip that Adam posted, i.e trying to open the clip back up once it's in position.

IMO the clip is a bit crap, mine was replaced with a Schumacher clip and the diff is like night and day now, I think the Schumacher clips must be stronger ?

Good luck.

whats the part number of the c clip?

andys
18-10-2011, 09:17 PM
No idea on part no.
Apparently it's the clip from the couger diff, anyone know the no. ?

gainsy
18-10-2011, 09:41 PM
The exploded view on the schumacher site shows the clip to be part number U2573
Looks like you get 3 clips for £5.50 + some other stuff which i guess you could give to someone with a cougar :)

losichris
18-10-2011, 10:05 PM
just rebuilt the diff. now it feels very tight and not slipping.
but when i put the car together the car stops when it turns or becomes very difficult to turn?
and when i slacken the diff off it slips


i think a whole new diff is needed, i think this one is knackerd

jkclifford
18-10-2011, 10:52 PM
The exploded view on the schumacher site shows the clip to be part number U2573
Looks like you get 3 clips for £5.50 + some other stuff which i guess you could give to someone with a cougar :)


£5.50 for circlips!! Jesus Christ take the original to any enginerng firm / supplyer, you will get 100 of em!

gainsy
18-10-2011, 11:21 PM
£5.50 for circlips!! Jesus Christ take the original to any enginerng firm / supplyer, you will get 100 of em!

Completly agree but they are still £2 cheaper than the durango ones!! although you get 4 from durango!!!

jkclifford
19-10-2011, 02:52 AM
I've had no problem, but could this be that the black hard coating is thicker in the rebate, so some outdrives, and the circlip is not getting the surface area to press against ?

Similar problem with some of the 410 wishbone hangers when the inserts were tight?

Maybe give the groove a sctach out with a dentist type pick?

sly
19-10-2011, 06:01 AM
just rebuilt the diff. now it feels very tight and not slipping.
but when i put the car together the car stops when it turns or becomes very difficult to turn?
and when i slacken the diff off it slips


i think a whole new diff is needed, i think this one is knackerd



My guess would be that you have cut the little ears/lugs of the nut holder that you need to be in place to stop it slipping.

OneKiwi
19-10-2011, 06:36 AM
then its just going to spin when you tighten it, takes away the point of having them

Origineelreclamebord
19-10-2011, 07:42 AM
> Link to Step 13/Bag D of my DEX210 Building Thread. (http://www.tamiyaclub.com/forum/index.php?showtopic=64132&st=4&start=4) <

I hope this clears things up a bit. I won't be testing my diff unfortunately, but I hope the pictures clear up what should be done, in combination with the information from the manual, advice that Adam Skelding posted, suggestions from Oople members and my attempts to use common sense during the build :)

The result is a diff that won't slip, can be tightened further than it is right now, feels smoother than many other diffs I've built and there's enough room for the driveshafts to go in on both sides and move freely!

PS: Link to full build thread. (http://www.tamiyaclub.com/forum/index.php?showtopic=64132)

losichris
19-10-2011, 09:09 AM
ive officially given up on this diff, ive followed everyones advice and spent the last 4 mornings before work trying to get it right.
and can only assume theres something damaged now due to it being taken apart so many times.
may wait for the spare parts, if durango cant get a move on and sort that out. then its going on oople trader section :bored: because im really fed up!

Origineelreclamebord
19-10-2011, 09:31 AM
ive officially given up on this diff, ive followed everyones advice and spent the last 4 mornings before work trying to get it right.
and can only assume theres something damaged now due to it being taken apart so many times.
may wait for the spare parts, if durango cant get a move on and sort that out. then its going on oople trader section :bored: because im really fed up!

I'm sorry to hear that :( Are you using circlip pliers and are you sure the circlip isn't damaged?

I'm sure there are many people willing to help you out on this, perhaps a member here can look at it for you? (I can offer you to look at it, but I don't live in the UK). If you do feel you want to sell it, I'm sure there are also enough people willing to buy it from you, even if the diff has issues.

Adam Skelding
19-10-2011, 09:36 AM
I did & got no response
Anyway i better stop derailing Chris's thread
Hope you got it sorted Chris

Sorry Gainsy, but you did get a response which you replied to again.

Adam Skelding
19-10-2011, 09:40 AM
ive officially given up on this diff, ive followed everyones advice and spent the last 4 mornings before work trying to get it right.
and can only assume theres something damaged now due to it being taken apart so many times.
may wait for the spare parts, if durango cant get a move on and sort that out. then its going on oople trader section :bored: because im really fed up!

I'm sorry if this sounds repetitive, but if you have a particular issue with your kit please contact us direct at [email protected]
Where as previous customers have found we offer direct one-to-one service and try to sort out your individual problem.
On forums we only try to offer hints, tips and other 'general' advice.

If you don't contact us, we can't help you... It really is that simple.

:thumbsup:

Northy
19-10-2011, 09:47 AM
Post #9
Post #21

Contact TD

gainsy
19-10-2011, 09:54 AM
Sorry Gainsy, but you did get a response which you replied to again.

Correct i did get a answer to my original email about the shock shafts, steering link & the c clip, didn't get a reply to the next suggestion about making the manual more understandable to newbies & my question about slim front wheels

mikeyscott
19-10-2011, 09:57 AM
Would like to add Team Durango are very helpful when you follow the correct communication path.

For me if I have a problem with xyz product I'll ALWAYS discuss with the manufacturer before even thinking of posting on a forum.

I've seen people really slate a product in public before asking the manufactuer and then they wonder why the manufacturer doesn't appear "friendly".

I had issues with my first batch SV which I discussed with Schumacher, they went above and beyond in my view for Customer Service. I was very happy and it was all because I addressed it with them direct in a polite manner rather than bashing on a forum or facebook etc etc.

I have done the bashing on forums in the past, but only when it's due... A main Volvo dealer wouldn't resolve some outstanding issues with a car that I paid £13k for. They ignored emails, telephone calls and so forth. After a very public bashing with clear and accurate facts Volvo UK stepped in and resolved it.

Adam Skelding
19-10-2011, 10:05 AM
Correct i did get a answer to my original email about the shock shafts, steering link & the c clip, didn't get a reply to the next suggestion about making the manual more understandable to newbies & my question about slim front wheels

We are doing a hints and tips section for the website which like we did with the DEX410 will cover the common maintenance and set-up areas of the car.

Slim front wheels - I assume you are talking about the 'Old' Stagger rib.
The simplest method is to cut the wheel down as shown below.

gainsy
19-10-2011, 10:13 AM
Ok thanks for that Adam
Will the wheels be available soon? or are there any other makes that will fit for the time being till the durango ones are available? i will give the wheel cutting a go when they come out

Adam Skelding
19-10-2011, 10:15 AM
Wheels are due in next week.
You can 'Drill / Ream' a B4 wheel out to 10mm and then press in the Durango bearings. It will help get you away until you get the proper ones :)

mikeyscott
19-10-2011, 10:16 AM
Wheels are due in next week.
You can 'Drill / Ream' a B4 wheel out to 10mm and then press in the Durango bearings. It will help get you away until you get the proper ones :)

Cougar SV front wheels are the same size as B4 wheels I think (correct me if I am wrong).

gainsy
19-10-2011, 10:16 AM
Thank you :thumbsup:

Origineelreclamebord
19-10-2011, 10:28 AM
Would like to add Team Durango are very helpful when you follow the correct communication path.

For me if I have a problem with xyz product I'll ALWAYS discuss with the manufacturer before even thinking of posting on a forum.


+1: Last year I built a DEX410 of the very first batch, and I found there were 2 screws not in the kit, and I broke the battery snap pin during the build (It just snapped when I tried to get in on there :eh?:). They pretty much just asked the kit number, my adress and easily within 14 days of contacting them I had my parts :thumbsup:

A whole lot different than some manufacturers I contacted, from which I never even got a reply.

Anyhow, though I've had a blast building my DEX210, I did come across one or two small issues. The biggest one being that one of the rear wheels is out of balance: The inside side of the wheel probably got a nudge when it was still cooling, or it has shrunk unevenly. The other issues were with screws: I had one screw without a thread :lol: But I had the right length in the leftover screws from the build, so no problems there. And lastly I had to use M3x10 screws in two places where M3x8 was adviced - since the 10mm screws fitted I see nothing to complain about there :)

PS: I shall now stop going off-topic.

losichris
19-10-2011, 01:34 PM
email sent re.diff. Trying to get some circlip pliers online and schumacher circlips

losichris
19-10-2011, 01:53 PM
email sent re.diff. Trying to get some circlip pliers online and schumacher circlips

Steve
19-10-2011, 02:02 PM
Her is some links for the Circlip Pliers and the Schumacher Circlips

http://www.racing-cars.com/pp/Old_Cars_and_Parts/Havoc/HW010.html

http://www.racing-cars.com/pp/Old_Cars_and_Parts/Nitro_21_XTR-3E/U2631.html

mikeyscott
19-10-2011, 02:02 PM
email sent re.diff. Trying to get some circlip pliers online and schumacher circlips

These are what I used with no issues as I had them for my SV

http://www.racing-cars.com/pp/Manufacturer/Schumacher/HW010.html

stegger
19-10-2011, 05:37 PM
> Link to Step 13/Bag D of my DEX210 Building Thread. (http://www.tamiyaclub.com/forum/index.php?showtopic=64132&st=4&start=4) <

I hope this clears things up a bit. I won't be testing my diff unfortunately, but I hope the pictures clear up what should be done, in combination with the information from the manual, advice that Adam Skelding posted, suggestions from Oople members and my attempts to use common sense during the build :)

The result is a diff that won't slip, can be tightened further than it is right now, feels smoother than many other diffs I've built and there's enough room for the driveshafts to go in on both sides and move freely!

PS: Link to full build thread. (http://www.tamiyaclub.com/forum/index.php?showtopic=64132)

How come your not using the black molybdenum grease on the thrust bearing ? :confused: Every diff i have ever built uses the black grease.

Origineelreclamebord
20-10-2011, 06:53 AM
How come your not using the black molybdenum grease on the thrust bearing ? :confused: Every diff i have ever built uses the black grease.

I have :) Believe it or not, that is the molybdenum grease from the kit that you can see on the thrust washers. It came out a little light in colour due to the flash of the camera (without the flash the picture would've been all black). I added some more grease inside the cage of the bearing after the picture, so plenty of moly grease there! :thumbsup:

sunbeam
20-10-2011, 07:20 AM
My circlip is in my diff and working well. The Durango 210 diff, for me, is perfect. I built it as the manuel, and no probs at all. I found it super smooth and no problems with getting to the right tension first time.

Having just come from an SV and messing with cone washers that 'ARE' shit, I would say the 210 dif is spot on, even the circlip.

Unfortunatly, as I said, my diff is finished and working, but the circlip in the 210 seemed to me to be thicker than the SV circlip ( I rebuilt my SV diff 4 days ago for the 3rd time in 2 months)

Basically, get the 210 circlip, pre strech it a little, rounded side goes towards the SMALL trust race and use PROPER pliers (or Dremeled ones) Compress it as LITTLE as you can. I put it in at an angle, then removed the pliers and pushed it the rest of the way with a flat screw driver. This way the circlip never gets compressed more than it has to. By pre streching it and not squashing it when fitting, you get a super tight fit when it's fully home.

Mine has been test run, painted and ready for the track tomorrow, so I HAVE built this car to know!

footey
20-10-2011, 09:10 AM
ive officially given up on this diff, ive followed everyones advice and spent the last 4 mornings before work trying to get it right.
and can only assume theres something damaged now due to it being taken apart so many times.
may wait for the spare parts, if durango cant get a move on and sort that out. then its going on oople trader section :bored: because im really fed up!


how about trying to fit a tamiya 201 diff in the car

Origineelreclamebord
20-10-2011, 11:22 AM
how about trying to fit a tamiya 201 diff in the car

That might work yeah, though if it fits you'll at least need to cut down the outdrives, they are quite a lot longer than the Durango outdrives :lol:

daz
20-10-2011, 02:22 PM
ive officially given up on this diff, ive followed everyones advice and spent the last 4 mornings before work trying to get it right.
and can only assume theres something damaged now due to it being taken apart so many times.
may wait for the spare parts, if durango cant get a move on and sort that out. then its going on oople trader section :bored: because im really fed up!
Il give you £90 including postage for it, pay pal waiting but you pay the fees:thumbsup:

Big G
21-10-2011, 09:33 PM
mine gave up at 10 laps so I stripped it down. once out of the car I pulled the 2 outdrives and they just came apart in my hands lol. The thrust bearings and screw were all still attached to the other half of the diff haha

my cir clip was in backwards which was visible on very close inspection. Re-fitted it all back and I can't get it to slip in my hands.

Will give it a blast around Cov track on Sunday to test :)

mikeyscott
21-10-2011, 10:55 PM
Many thanks.

I will re check mine tomorrow. Any damage etc

Jamesy
22-10-2011, 10:36 AM
The diff in my 210 slipped on its first runs out.

On closer inspection I found that some of the oil left on the diff halves from the manufacturing process had mixed with the diff lube. I would say that it is very important to ensure all diff parts are thoroughly cleaned before building.

I rebuilt my diff after a thorough cleaning and all is good now.

Whilst I had the diff apart I fitted some Lazy balls. These are some of the best diff balls I have used! Really smooth diff action.

Big G
22-10-2011, 12:55 PM
I fitted lazy balls too whilst building the 1st time. so smooth :D

mikeyscott
24-10-2011, 06:40 PM
Well I decided to check the c clip and I can't feel any difference.. So I have put it back together mmmmm :(

losichris
24-10-2011, 07:09 PM
good job theres decent people on here helping out
7 days and no reply from durango about the diff :thumbdown:

bigred5765
24-10-2011, 07:16 PM
glad i could help Chris, lol has it been OK since??

mikeyscott
24-10-2011, 07:31 PM
good job theres decent people on here helping out
7 days and no reply from durango about the diff :thumbdown:

Have you phoned them?

losichris
24-10-2011, 08:09 PM
glad i could help Chris, lol has it been OK since??

cheers mate, yeah seems ok so far. see how the first run goes :drool:

losichris
24-10-2011, 08:10 PM
Have you phoned them?

havent phoned no, sent 2 emails though.
if i hadn't been given the help, proberbly would have phoned them by now though

hottuna
24-10-2011, 08:51 PM
I tested both my diffs last sunday on a high grip carpet track without problem. I don't know in which way i installed the clips, it seems to work either way.
Is it the way you install them (how much you compress) or pure luck? Anyway, i don't see a problem, and if Durango did on their tests they should have did something about it.

drop4205
26-10-2011, 10:32 AM
have you measured the thrust washers and put the smaller one in first then the caged thrust ball then the larger thrust washer. I helped a friend build his and ran on carpet last night after we broke it in and all is tight and smooth as butter. And on another note the ball cups idk what happened but he hit a few things that were not gonna move pretty good and no issues with his cups.

kwiksi
26-10-2011, 11:20 AM
The diff balls/thrust in the kit carbide? Just want to know if I should invest in some before the build.

neil_p
26-10-2011, 11:42 AM
The diff balls/thrust in the kit carbide? Just want to know if I should invest in some before the build.

No they are steel. I have used RC Lazy balls in both diff and thrust and very smooth.

The orientation does not have any issues on performance, but good engineering practice should be to have the square edge in the direction you insert the clip to give a more positive engagement. These clips are just stamped out. Using the kit one with no issues at all.

drop4205
27-10-2011, 12:33 AM
the stock diff built with associated thrust grease and stealth grease make for a diff thats smooth as butter. If you were to upgrade later carbide diff balls and ceramic thrust is the way to go. just my .02

1armed1
27-10-2011, 01:42 AM
The diff balls/thrust in the kit carbide? Just want to know if I should invest in some before the build.

Hit up Fred at Bfast,

He sent me some goodies for my 210 and the diff is like butter!

aztecz
01-11-2011, 03:34 AM
Pardon my ignorance if this been asked before but what is the size of the thrust bearing in the diff?

4_cell_racer
01-11-2011, 05:12 PM
Bought some Schumacher circlips (U2631) after reading this thread to keep in my pit bag.
I broke the original circlip in my diff last night :blush: so today I tried the Schumacher circlip and it too big to fit in the our drive :confused:
Anyone know why this could be?
Cannot find the original TD circlip in stock any where either :cry:

Help anyone

**EDIT**

Just looked on Schumacher's web site and the clips pictured are different to the clips I have! I get all the 'E' & 'C' clips but only 2 circlips! the pic on there site shows 5 circlips!

stegger
01-11-2011, 06:50 PM
U2573 has 3 clips in fella ;)

4_cell_racer
01-11-2011, 07:02 PM
U2573 has 3 clips in fella ;)

Steve..... Do them ones defo fit?

Andrew Twigger
01-11-2011, 07:26 PM
Bought some Schumacher circlips (U2631) after reading this thread to keep in my pit bag.
I broke the original circlip in my diff last night :blush: so today I tried the Schumacher circlip and it too big to fit in the our drive :confused:

I also had this problem with a couple of diffs I had from a borrowed Cougar. This either means the circlips in these particular diffs did not have original parts, or the clips people on here are referring to are from something that is not a Cougar.

My Durango kit circlip felt quite weak by the time I'd rebuilt it numerous times to rid the 'lump' a bent clip gives you, so I'm also keen to learn which clip people are using?

OneKiwi
01-11-2011, 07:41 PM
Won't rebuilding it several time just weaken the origianl clip

mattr
01-11-2011, 07:50 PM
Won't rebuilding it several time just weaken the origianl clip

Yes. Should just buy a job lot from a bearing/nut/bolt supplier. It's a stock size. Should cost Pennies (if you buy 100 at a time)

Pretty sure neither manufacturer are daft enough or rich enough to tool up a special circlip for the tiny volumes they make. minimum order is probably a million clips.....

paulc
01-11-2011, 08:00 PM
These are the circlips im using in my diff and it's been fine :)

http://www.ebay.co.uk/itm/STAINLESS-STEEL-8MM-INTERNAL-CIRCLIPS-CIRCLIP-DIN472-/280752767804?pt=UK_DIY_Material_Nails_Fixing_MJ&hash=item415e2b433c

WHITTLER555
01-11-2011, 09:26 PM
Hi its an 8mm internal circlip, I bought 10 from my local ironmonger for 70p, fits perfectly, ran all last Sunday, no problems.

mikeyscott
01-11-2011, 09:29 PM
I couldn't feel any diff on the cir clip so just built the diff as is and had no probs. Only change - RC lazy balls.

Will wait for TD to do a tips article....

Gear diff longer term though.

mikeyscott
01-11-2011, 09:31 PM
Hi its an 8mm internal circlip, I bought 10 from my local ironmonger for 70p, fits perfectly, ran all last Sunday, no problems.

Could you provide contact details so I can get some spares?

mattr
01-11-2011, 09:53 PM
http://simplybearings.co.uk/shop/product_info.php?products_id=82661

http://www.bearingboys.co.uk/D1300_0080_8mm_Internal_Circlip__Pack_of_100_-17503-p

Can see the difference in volume pricing........ tbh, i'd buy 100 for 9 quid and just dish them out like sweeties.......

Andrew Twigger
01-11-2011, 11:55 PM
http://simplybearings.co.uk/shop/product_info.php?products_id=82661

http://www.bearingboys.co.uk/D1300_0080_8mm_Internal_Circlip__Pack_of_100_-17503-p

Can see the difference in volume pricing........ tbh, i'd buy 100 for 9 quid and just dish them out like sweeties.......

Great idea. I'll give you £2.50 for 10 to get you going!

mattr
02-11-2011, 05:37 AM
:D I don't actually have a 210 yet.........Q1 next year is the plan!

kabilay
02-11-2011, 10:12 AM
First time with a ball differential and i am confused. Below is what happens with mine.

When i turn the one wheel forward the other is moving forward also. What is happening? Is this a problem? Should the other wheel turn to the opposite direction as the gera diff?

When i hold the spur and one wheel, the other does not spin which is correct if i am not wrong.

Dazzler
02-11-2011, 10:26 AM
If you hold the spur and turn one wheel, the other wheel should rotate in the opposite direction. If you hold the spur and one wheel, and try to turn the second wheel, there should be a good amount of resistance before you can make the diff slip / second wheel rotate.

Also, when the wheel does turn, it is useful to identify whether it is the diff which is slipping or the actual slipper on the spur. You'll obviously need to have the spur gear removed to hold the spur, so you should see if the actual slipper is slipping..

kabilay
02-11-2011, 10:30 AM
No both wheels turn the same dirrection when i spin only one

Dazzler
02-11-2011, 10:37 AM
I'm struggling to see how that can happen if you are holding the spur gear preventing it from rotating, then turning one wheel by hand...:confused: if the diff was not right, you'd probably see a poor / rough counter rotation, or nothing at all.

Other than that, you'd have to have locked the two outdrives together somehow, without applying pressure to the diff balls.. This would mean you would have no drive either...

kabilay
02-11-2011, 10:41 AM
I'm struggling to see how that can happen if you are holding the spur gear preventing it from rotating, then turning one wheel by hand...:confused: if the diff was not right, you'd probably see a poor / rough counter rotation, or nothing at all.

Other than that, you'd have to have locked the two outdrives together somehow, without applying pressure to the diff balls.. This would mean you would have no drive either...


When I hold the spur everything is fine.
The problem is when i do not hold the spur. just spin one wheel forward----> the other one move forward too. (Is this the case where the balls are not spinning but just rub against the plates?

mattr
02-11-2011, 10:44 AM
Means that there is more drag in the diff than there is resistance to the spur turning. Happens on all diffs.

(When both wheels turn in the same direction, your spur is rotating too, right?)

Dazzler
02-11-2011, 10:46 AM
That sounds normal really, the drive train will try to rotate if you are running a tight diff. Have you tried holding the spur and one wheel, then trying to rotate the other?

kabilay
02-11-2011, 10:48 AM
Means that there is more drag in the diff than there is resistance to the spur turning. Happens on all diffs.

(When both wheels turn in the same direction, your spur is rotating too, right?)


Yes:thumbsup:.
But i have not test what Dazzler says :"If you hold the spur and turn one wheel, the other wheel should rotate in the opposite direction"

kabilay
02-11-2011, 10:49 AM
That sounds normal really, the drive train will try to rotate if you are running a tight diff. Have you tried holding the spur and one wheel, then trying to rotate the other?


I guess the diff is too tight. I'll try the above to see if everything is ok.

Dazzler
02-11-2011, 10:53 AM
That doesn't necessarily mean its too tight... But what you need to do is make sure that your slipper slips before the diff slips, and that the slipper doesn't slip too much on acceleration.. So I wouldn't back it off just yet..

kabilay
02-11-2011, 10:54 AM
That doesn't necessarily mean its too tight... But what you need to do is make sure that your slipper slips before the diff slips, and that the slipper doesn't slip too much on acceleration.. So I wouldn't back it off just yet..


How can i do this? :confused:

Dazzler
02-11-2011, 10:57 AM
As posted above, hold firm the spur and one wheel, then try to turn the second wheel. This will load up the drive train, and either the diff will slip, or the slipper on the spur will slip. You can see the slipper on the spur, so if this isn't slipping, the diff is.

mattr
02-11-2011, 11:03 AM
Slipping slipper = ideal, cheap to run, cheap to replace (eventually)

Slipping diff = not very good, flattened balls, grooved plates, crunchy running. Expensive to repair (well, more expensive than 5 quids worth of slipper pads!)

X7tristan
02-11-2011, 11:47 AM
Steve..... Do them ones defo fit?

No, the clips from Schumacher U2573 do not fit, they're too big.

paulc
02-11-2011, 04:51 PM
How can i do this? :confused:

This is worth a look at about building and setting diffs ;)

http://www.rctech.net/forum/electric-off-road/512013-how-properly-build-break-ball-differential-slipper-clutch.html

WHITTLER555
02-11-2011, 04:55 PM
Could you provide contact details so I can get some spares?


Hello, my local supplier is:

www.thetoolwarehouse.co.uk

01282 615 734

You can have a couple off me at the next Chadderton meeting??

OneKiwi
02-11-2011, 11:00 PM
Blew the bearing that is on the layshaft today BB 5x8x2.5mm 601022

Also I tried out the cheap Bullistorm 120A esc with a 6.5 (too much I know but all I had)

Worked really well im happy with it. Gonna mount it more permanently and fix the wiring and give it another test on sunday then race weekend 11-13th

Ill even thr out the 60A with a 8.5T when it all arrives