View Full Version : 511 Gear Diff 54329
MHeadling
24-10-2011, 03:42 PM
http://www.rcmart.com/catalog/rc-db01-tamiya-gear-differential-unit-p-34347.html
Anyone tried them yet?? A few lads have tried the Spec R diffs but these seem to fail. Lets hope these are a bit stronger...........
qatmix
24-10-2011, 06:35 PM
Mine are still in the post. They have been built for the DB01 so there is no reason they won't hold up, for the price (28inc delivery for 2) it's a risk I am willing to take.
Northern Monkey
27-10-2011, 07:39 AM
Built and installed mine last night, gears seem a bit meatier than the Spec R's will find out this weekend at the Torch Winter series. They wouldn't fit with the Fredricks covers tho but as there sealed shouldn't be a problem. Super smooth tho :thumbsup:
MHeadling
27-10-2011, 08:32 AM
Good stuff, let us all know how they run and what diff oils you end up running!
Northern Monkey
27-10-2011, 10:04 AM
Will do... a friend's been running the Spec R diffs in his 511 for a while and he recommended 7000 front 2000 rear from his set-up. So have used this as a starting set-up for now. (He's usually right) :woot:
By the way the track is Hi grip astro (but that will depend on if it rains) :thumbsup:
with mine i have a problem, i can't have the belt and the gear in the same line like i can have with the ball diff. have you this problem and how you solve it ?
for the fluid i use tamiya VG 2000 to the front and 1000 to the rear and i think it's a little bit hard for front and to soft for rear, i think to usr the 1500 to the rear.
Northern Monkey
27-10-2011, 12:57 PM
Haven't noticed a problem with mine and all I had to do was remove the Fredriks cover and liner, will have a look. Is yours a 511?
With regards to oils, yes the front should be thicker than the rear. In the same way that generally you should run your front diff tighter on a ball diff.
discostu
27-10-2011, 05:26 PM
Haven't noticed a problem with mine and all I had to do was remove the Fredriks cover and liner, will have a look. Is yours a 511?
With regards to oils, yes the front should be thicker than the rear. In the same way that generally you should run your front diff tighter on a ball diff.
i would have to disagree with this its down to personel prefrence this is not always the case
DaveG28
27-10-2011, 05:31 PM
So they don't fit with the Fredrik Diff covers?
discostu
27-10-2011, 06:13 PM
Built and installed mine last night, gears seem a bit meatier than the Spec R's will find out this weekend at the Torch Winter series. They wouldn't fit with the Fredricks covers tho but as there sealed shouldn't be a problem. Super smooth tho :thumbsup:
are the gears metal
MHeadling
27-10-2011, 06:25 PM
Looking at the pics id say no, look like a carbon plastic.........
Jan Larsen
27-10-2011, 06:46 PM
Gears are carbon plastics and if they hold to mod TC I see no reason why they wont hold up to mod offroad. Besides, using plastics saves a boatload of weight.
Northern Monkey
27-10-2011, 06:54 PM
I agree that it is down to personal preference, as is any setup tip. Every bodies driving style is different therefore some setups will work and some will not work for them. I am just commenting on what I and others that I raced with have found. Dependent on the conditions and track.
No the gears aren't metal but the spindles they go on are and the teeth appear deeper. I might be wrong, as I'm going on a comment from a friend that has the Spec R diffs
No they don't fit the Fredriks cover. Because the covers line the gearbox the gear diff is too tight and not free running
[/B]
i would have to disagree with this its down to personel prefrence this is not always the case
simoncrabb
28-10-2011, 01:56 PM
We've just got some of these in stock, in the UK, very limited numbers.
But, they come at a price, £29.99 EACH.
Get in touch if you want some.
(Also, finally got a FEW 511 shells in stock too...)
DaveG28
30-10-2011, 11:39 PM
Gave mine first run today. With 10000fr and 5000rr felt very similar to ball diffs, but just a touch sharper and more consistent! They were not new ball diffs I compared them to though!
One thing I think is pants, the rebuild kit doesn't include gaskets, so look after them!
Think I slightly overfilled the front one, how big a problem is it? Covering the bevel gears basically fills that half of the cup!
DaveG28
31-10-2011, 05:09 AM
Having stripped the car down to take a look, one of the diffs is leaking out of one sides outdrive, what's the best way of trying to sort it?
Is it best to use more shims to pressure the oring, or is that just going to screw up the gear mesh?
Do I just change the oring and hope that fixes it? Or can I grease/glue around it?
Or just live with it? How much can leak out before I need to refill?
with mine it's hard to ajust the bearing and i can't use enouth shim to ajust the position of the diff in order to have the center off the gear in the same line with the belt, like i can do with the ball diff.
i think i'll have to much plastic, i compare with a friend car and he don't have this problem.
i'm going to pass sand paper on the plastic part and i think it will be good
qatmix
31-10-2011, 09:36 AM
Having stripped the car down to take a look, one of the diffs is leaking out of one sides outdrive, what's the best way of trying to sort it?
Is it best to use more shims to pressure the oring, or is that just going to screw up the gear mesh?
Do I just change the oring and hope that fixes it? Or can I grease/glue around it?
Or just live with it? How much can leak out before I need to refill?
Dont shim it anymore, it can strip the gears.
All I do on mine is to sand the rear of the internal gears (gently to ensure they are smooth, only takes about 30 seconds). Then build it as instructions. I do use a few parts of AE green goo for piece of mind.
I havent had any leaks since using the green goo (This was on the spec-R diff)
I since built my new Tamiya v2 ones like this and they havent leaked a drop even with thinner oil (1000 wt)
Oh and when I did at first have a leaking diff, I ran it until it didnt feel right. (which after 4 months I just changed it, and it still had quite a lot left). Even the smallest of leaks can look quite dramatic as they are doing quite a few times a second.
DaveG28
31-10-2011, 05:30 PM
Cheers guys, I did my best to flatten the rears of the gears, maybe not enough though, or maybe I went too far on one with my knife, might that be it?
qatmix
01-11-2011, 09:29 AM
I don't think that it would make much of a difference, although maybe if the cut misshaped the gear a tad it might act like a ship prop and pull more oil behind it.. although that's really unlikely.(I'm going off at a tangent)
Also if its filled too much it could leak.
The other thing thats important is to ensure when its screwed together that you screw it on in a cross pattern as if the two parts don't close in a true manor that could let some oil out.
Again, I would just rebuild and use the green goo liberally on parts that you think could leak and go from there.
For those that have got the diffs, does the instructions list the part numbers of the spare parts (like the gasket and planetary gears)?
Thanks
Donutt
07-11-2011, 06:44 PM
Not on my instructions. Unless it's in the japanese text...
(english is just simple descriptions)
Cheers mate, mine are still in the post and was wondering about getting hold of some service spares. Guess that'll have to wait for a bit........
qatmix
08-11-2011, 11:15 AM
on onroad I have run a gear diff since January and it hasn't needed any new parts. Obviously off road could be a bit more harsh on the gears but I would think they would last a fair while.
fastinfastout
08-11-2011, 01:01 PM
at $21US for a gear diff, you cannot complain really even if you have to buy a new gear diff every few months.
It would cost you just as much with new carbide/ceramic balls, thrust assemblies, yet you wouldn't have the consistency of a gear diff.
I'll probably end up doing that, get a whole spare unit in a few weeks time. Just thought I might be able to get some spares in the meantime 'just in case' as knowing my luck I'll end up stripping a gear on my first run......
Carno
20-11-2011, 03:55 PM
I finished building my diffs yesterday. Thought i'd give them a spin on our new track today.
Built them as in the manual using 2 shims per side and with the oil supplied by tamiya which is too thin.
Ran 2 packs, or better abused the car for 2 packs, and the rear diff isn't sounding and feeling healthy anymore.
Popped a drive shaft twice so that might have influenced things.
Gonna open the rear diff up when I have the time to see what's wrong.
Probably gonna use 3 shims next time and add some more spacers in my dampers.
Hi guys. Another weekend has gone by. How are the diffs holding up? :D
Any updates on the diffs?
fastinfastout
13-12-2011, 03:49 AM
I've had 1 race meet with mine, and there one of my gear diffs are leaking a little, and I have 20k oil in there. Diff was built with green slime.
DaveG28
13-12-2011, 01:52 PM
Mine have done just under an hour...they both leak, but are also silly smooth and consistent. Tbh, if your good at building ball diffs I'm not sure they are advantage, but they definitely help someone like me!
makinwaves
13-12-2011, 02:53 PM
Mine lasted for a few runs at the MK GP but then stripped the gears in the rear on my TQ run... LOL ;) (haven't opened them up yet...).
Just got new gear sets in the post so i'll rebuild them soon, the question is: last time I used 1 extra shim on one side as it felt notchy with 1 each side. How many shims have you guys been trying? Do they need the extra shims to make it super tight?
Mark
Chris
14-12-2011, 09:39 AM
Mine lasted for a few runs at the MK GP but then stripped the gears in the rear on my TQ run... LOL ;) (haven't opened them up yet...).
Just got new gear sets in the post so i'll rebuild them soon, the question is: last time I used 1 extra shim on one side as it felt notchy with 1 each side. How many shims have you guys been trying? Do they need the extra shims to make it super tight?
Mark
Did you use the extra shim when you stripped it?
makinwaves
14-12-2011, 09:52 AM
Yep. Was going to run one each side but it felt notchy when built.
Maybe it does need to be tighter then...
qatmix
14-12-2011, 12:03 PM
If your diff is notchy after just a few runs you have either made it way too tight or not shimmed it well enough.
]With the gear diffs you dont want to tighten the screws really tight. That will mess up the gear diff. You just want to tighten it until the screws feel seated.
I drop a bit for green slime in mine and dont get any leaks.
On the buggy I use 2 shims each side, on my TC i now use 3.
Here is very good guide on how to make a sweet diff
[URL="http://www.youtube.com/watch?v=m_DhcfcO8dI"]http://www.youtube.com/watch?v=m_DhcfcO8dI[/URL
DaveG28
09-01-2012, 02:07 AM
I've been trying to find an issue in the drivetrain and realized today that my rear diff fouls against the rear shock tower! Anyone else had this issue?
CraigM
09-01-2012, 09:14 AM
What's a good starting point for diff oils front and rear? I'll be running on medium grip hard packed dirt
Chris
25-01-2012, 10:48 AM
How to build the gear diff:
http://youtu.be/m_DhcfcO8dI
Himey97
05-02-2012, 03:19 PM
Getting a DB01R and have read many recommendations to switch to the 51286 differential joints as a stronger upgrade on the ball diffs.
Would it be a better option to just switch to the 54329 Gear diffs?
The complete gear diff 54329 is cheaper than the 51286 out drive.
What am I missing ?
newb
brianh
30-04-2012, 12:10 PM
hi folks, just had a question about these diffs. after I've built them and installed them but when I set them up in the car the wheels don't turn, has anyone had this problem, Im talking about trying to turn both rear wheels in the same direction, the diff works fine spin one outdrive and the opposite one turns in the other direction but once in car and the belt goes on the wheels don't spin, any help would be great
Dalton
30-04-2012, 12:41 PM
Look for it binding on the edge of the gearbox and/or do you have fredrik gear covers fitted with them as they dont fit ?
brianh
30-04-2012, 01:52 PM
No I don't have fredrik gear covers, ill have to have a look to make sure there not binding somewhere. just to be sure can I use a front one way and a slipper clutch with this diff in the rear, if not I have a second one of these diffs
gurnell
30-04-2012, 08:36 PM
No I don't have fredrik gear covers, ill have to have a look to make sure there not binding somewhere. just to be sure can I use a front one way and a slipper clutch with this diff in the rear, if not I have a second one of these diffs
Have you got the belt tensioners in the right way. If you've got the diff positioned low the diff gear will probably be tight against the chassis. I also remember somebody else mentioning that the gear diff can also rub against the rear shock tower. I hope this helps.
trowta
10-05-2012, 03:11 AM
what size hex fits the diff housing screws? I have tried 1.5mm which is too big and .050 which is too small....
It is 1.5mm but the hex is very shallow so it doesn't feel like it's taken hold very well.
trowta
10-05-2012, 03:39 AM
I have hudy tools and the hex doesn't fit at all
Strange, I've got Hudy drivers and 1.5mm fits.
trowta
10-05-2012, 09:50 AM
Strange, I've got Hudy drivers and 1.5mm fits.
I had to grid the tip to get it to fit... what fluids would you run on outdoor dirt med grip?
fastinfastout
10-05-2012, 11:48 AM
yeh I had to use an older well used 1.5mm tip, as my newer ones were too big oddly enough......
I run my diff in a DB-01 which is a fair bit heavier than a 501/511.
I've been using 7k CST oil in the front and 3k CST oil in the rear and this suits my driving style.
AaronR
02-09-2012, 02:00 AM
Anyone else have gear diff feedback for a 511?
After much hesitation, I will purchase and build one soon.
I say one, so is anyone running a gear diff in the rear only (with ball diff up front)?
rcaddict
02-09-2012, 02:24 AM
Anyone else have gear diff feedback for a 511?
After much hesitation, I will purchase and build one soon.
I say one, so is anyone running a gear diff in the rear only (with ball diff up front)?
I am running a gear diff in the rear and a ball diff in the front of my 511. It seems to be the perfect combo for me because I like to run my rear diff loose and my front diff tight. Having a gear diff in the back means I only have to rebuild one diff instead of two, and I can adjust my front diff as tight as I want to by using a ball diff. I get to have my cake and eat it too. Its a stellar setup and I highly reccomend it. :thumbsup:
Chris
10-09-2012, 07:11 PM
No more broken gears:
54428 Steel Bevel Gears for TA06 Gear Diff Unit (November)
rcaddict
11-09-2012, 06:34 PM
No more broken gears:
54428 Steel Bevel Gears for TA06 Gear Diff Unit (November)
Are DB01 and TA06 gear diffs using the exact same size bevel gears?
Aussie Top Force
12-09-2012, 11:20 AM
http://www.oople.com/rc/photos/2012national-epr/
AaronR
14-09-2012, 11:08 AM
Hrm, so just the opposite of what I was thinking! Thanks for the link Top.
Front ball diffs last so long though! :wtf:
rcaddict
16-09-2012, 04:20 PM
Actually, you're right, ball diffs do last longer in the front.
Lee would run the gear diff in the back and the ball in the front as I do, except the plastic bevel gears are getting chewed up in the rear with the hot motor he's running. He also has to put a ridiculously heavy oil in the front diff to keep it running "tight."
Once the steel bevel gears come out, watch him switch his front and rear diffs.
Chris
09-10-2012, 08:59 AM
Are DB01 and TA06 gear diffs using the exact same size bevel gears?
Yes
http://data6.blog.de/media/127/6653127_f4b2ae0a27_o.jpeg
Chris
09-10-2012, 09:02 AM
Is there a tighter O-ring (Kyosho?) available to prevent leaking?
Chris
09-10-2012, 09:54 AM
Is there a tighter O-ring (Kyosho?) available to prevent leaking?
Kyosho ORG05
(http://www.kyosho.de/?page=shop/product&offset=20&category_id=0&search=o-ring&ps_session=55q0o09ee0ti3ej161ogdja0q3&mod_title=product&setlang=deu#)
PredaTom
22-10-2012, 11:36 AM
Hi all,
it seems there are a lot of differences between brands of grease (AE, Losi, etc...).
Just would like to know if someone has experienced some different brands, and which one should be the best to use (durability for example).
Thanks all :)
trowta
23-10-2012, 12:01 AM
Yes
http://data6.blog.de/media/127/6653127_f4b2ae0a27_o.jpeg
where did you get this photo from?
Chris
23-10-2012, 08:43 AM
where did you get this photo from?
http://kentech.blogs.se/
Hi all,
it seems there are a lot of differences between brands of grease (AE, Losi, etc...).
Just would like to know if someone has experienced some different brands, and which one should be the best to use (durability for example).
Thanks all :)
Bump for a friend :)
By grease, Tom means diff oil.
Chris
17-12-2012, 04:13 PM
The steel gears are great! The gear diff is now indestructible.
Now waiting for the TRF511 upgrade set, or gear diffs for the TRF502X.
trowta
18-12-2012, 05:46 AM
any indication of when the TRF 511 upgrade will be out for a car that you can no longer buy?
djmcnz
18-12-2012, 11:12 AM
any indication of when the TRF 511 upgrade will be out for a car that you can no longer buy?
Tomorrow (19/12) according to Stella... ~US$220.
ky1977
18-12-2012, 12:42 PM
ETamiya is selling at $142.50.
http://www.tamiya-asia.com/shop/tamiya/84315/110/rc/trf511/upgrade/set-p-90058644.html
Somerwil
18-12-2012, 08:31 PM
I want to upgrade to gear diffs with the steel gears. Is there a part nr with all the necessary part included? Or do I need to order a plastic gear diff (54329), throw the plastics into the bin and replace them with the steel versions (54428).
The bits don't cost a fortune bit finding the items in 1 shop is more of a problem. Tips/ recommendations?
HeavyD99
19-12-2012, 02:27 AM
The steel gears are great! The gear diff is now indestructible.
Now waiting for the TRF511 upgrade set, or gear diffs for the TRF502X.
...err, and still leaks.
I read that there's a new spacer for the 417V5 that's wider/thicker to replace the three thin shims and helps seal it?
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.