PDA

View Full Version : DEX210 - What have people broken


mikeyscott
12-11-2011, 09:54 AM
In the process of ordering spares and so forth.

I haven't broken anything yet, but seen a few rear towers done


What have people broken and what did you do to break it?

gainsy
12-11-2011, 10:48 AM
So far just 1 front wishbone, cars don't agree with concrete :woot:

Dazzler
12-11-2011, 10:51 AM
I know of two cases of broken rear wishbones, and a bent inner rear hinge pin.

Both for good reason...

Big G
12-11-2011, 12:11 PM
not sure if this counts, but I cross threaded the spur cover onto the motor plate as it's difficult to get it in straight without a ball ended hex drive (which I have now)

Mitch269
13-11-2011, 05:46 AM
So far just a rear tower overall I think the car is pretty tough

sparrow.2
13-11-2011, 09:52 AM
not sure if this counts, but I cross threaded the spur cover onto the motor plate as it's difficult to get it in straight without a ball ended hex drive (which I have now)

I think I may have done mine too... Really annoying...

Andrew Twigger
13-11-2011, 10:32 AM
I think I may have done mine too... Really annoying...

Me 3!

aztecz
13-11-2011, 10:55 AM
Rear Shock Tower & Rear Front Plastic Suspension Mount..

sunbeam
13-11-2011, 04:23 PM
I have :-

TD 330337 F wish bones
TD 330338 R wish bones
TD 330339 Knuckle/hub set

All new unsed but not in packet £15 posted if anybody is interested ?
Paypal gift only, or collection.

kayce
13-11-2011, 04:29 PM
In the process of ordering spares and so forth.

I haven't broken anything yet, but seen a few rear towers done


What have people broken and what did you do to break it?

Other than typical buggy breakage items, that you've experienced in the past - it seems that threads like these always come with posts from people that do a lot of crashing, as it seems impossible to have broken anything yet as these cars haven't even had time to have been worn-in of yet. :lol:

Bungleaio
13-11-2011, 05:10 PM
Nothing up until today but I've now got a broken spur gear cover due to someone ramming me.

jayst
13-11-2011, 06:11 PM
rear shock towers x2
front shock tower
cracked a rear wishbone
bent inner hinge pin

graveltrap
13-11-2011, 06:39 PM
rear shock towers x2
front shock tower
cracked a rear wishbone
bent inner hinge pin

Animal!

Rear shock towers where popular at Coventry today, five or six got broken, usually as the result of a tumble after the double.

mikeyscott
13-11-2011, 06:46 PM
Yup I know the jump at Coventry. Did the same with my xx but didn't break the rear tower etc

TonyM
13-11-2011, 10:41 PM
Rear Shock Tower. It was big crash.:eh?:
Body split along the lower window line on both sides. Now held together with cricket bat tape.

gainsy
13-11-2011, 10:46 PM
Rear Shock Tower. It was big crash.:eh?:
Body split along the lower window line on both sides. Now held together with cricket bat tape.

My shell also split open today along 1 of the seam's :thumbdown:

old-man
14-11-2011, 09:01 AM
Rear Shock Towers here :mad: Carbon ones on the way :)

jamiekerr14
14-11-2011, 09:47 AM
I have run my car for Equiv. of a full days racing..

I broke 2 rear towers on my 1st time out with the car, they were not so much bad landing but catching a wheel in a high speed section and rolling. Which catches the top edge and snapped it. They have both broken in the exact same spot. And see almost like small air pocket or 2 there.

But I don't know enough about injection moulding and so on to comment much more. I raced the buggy yesterday morning and had 0 issues. And there was a large jump at torch and landed to flat a few times. For me this buggy is amazing I have never driven a 2wd in anger before but this one rocks! Got some carbon goodness on the way, but cant fault the buggy so far!

kartstuffer
14-11-2011, 12:30 PM
3rd weekend of racing and broke a rear shock tower, out in front no pressure just a hard landing after a jump. Definetly seems to be the weak spot on the car as i have seen others go . Carbon on the way .

mikeyscott
14-11-2011, 12:42 PM
3rd weekend of racing and broke a rear shock tower, out in front no pressure just a hard landing after a jump. Definetly seems to be the weak spot on the car as i have seen others go . Carbon on the way .

Plenty to be broken at the MK GP then! Good job I've ordered 5 packs!

stegger
14-11-2011, 01:18 PM
Plenty to be broken at the MK GP then! Good job I've ordered 5 packs!

That's £30 mate, why not a carbon rear tower ? :confused:

mikeyscott
14-11-2011, 01:20 PM
That's £30 mate, why not a carbon rear tower ? :confused:

Because I ordered them a while ago and got mates running the car too, so it's sort of for them too.

I doubt I'll be keeping the car anyway.

4_cell_racer
14-11-2011, 03:36 PM
WOW......after reading this thread I cannot believe racers are breaking sooo much on there 210's :o

I've ran mine (mainly indoors) on a tight track where there is always contact and have yet to break anything! and was at Broxtowe yesterday, raced all day and even had a off at the end of the straight (on the banked corner) and didnt break a thing.....and I aint the best driver out there (my results show this :D) and have my fair share of nose dives, awkward landings etc

Although now I've replied to this thread I'm bound to break something :p

hottuna
16-11-2011, 11:14 PM
I found a weak spot, the screws that hold the 320123-1. It takes the whole strange of the shock tower. I stripped the threads on both sides, and decided to make it more rigid. I added nuts on the inside of the plastic sides. No need to counter sunk as i did, low profile nuts will fit anyway.

Tweaky
17-11-2011, 01:18 PM
Or use 2mm longer screws to start with. Same with the front shock tower mounting screws need to be 2mm longer.


I found a weak spot, the screws that hold the 320123-1. It takes the whole strange of the shock tower. I stripped the threads on both sides, and decided to make it more rigid. I added nuts on the inside of the plastic sides. No need to counter sunk as i did, low profile nuts will fit anyway.

TARTMAN
17-11-2011, 01:29 PM
i have broken the carbon towers on my cat and cougar, carbon looks nice but breaks easily,. OK my driving is to blame for half of it, but i dont rate carbon for strenth.... at all...

TonyM
17-11-2011, 02:07 PM
Or use 2mm longer screws to start with. Same with the front shock tower mounting screws need to be 2mm longer.
Same here. I stripped one side and then fitted longer screws - all OK now.

gainsy
17-11-2011, 02:41 PM
i have broken the carbon towers on my cat and cougar, carbon looks nice but breaks easily,. OK my driving is to blame for half of it, but i dont rate carbon for strenth.... at all...

I was in DMS Racing yesterday & they now sell their own range of mounts called carbon flex which flex more than standard carbon, might be worth a call to see if they do them for your car :)

TARTMAN
17-11-2011, 03:40 PM
I am working on my own ones, with a dremmel and some various materials, just some testing to do and may have a cheap supply made by yours truly!:)


I was in DMS Racing yesterday & they now sell their own range of mounts called carbon flex which flex more than standard carbon, might be worth a call to see if they do them for your car :)

martin so16
20-11-2011, 10:39 PM
wel ive had 4 rear anti-squat blocks go the rear wish bone pins just tare out of them with not alot of impact done three at the mk gp this weekend not saying im the best driver out there and indoor racing is not that forgiveing but they are made from very flexible plastic.
and the HD ball caps pop off all the time on the 210 and the 410 v3 any one else had probs or is it just my bad driveing lol :woot:

jamiekerr14
20-11-2011, 10:50 PM
Im still really confused how you did 3 martin! Me and Mark were both very confused.. I had a ball cup from the front pop off in Q1 and Q2. Think I will do the same to my old 410 and get Losi HD cups and HPi ball studs.. since doing that on my 410 had next to 0 issues.. As the Rango HD ones seem better than the old.. but not by much!:(

Aran
20-11-2011, 10:56 PM
My steering turnbuckles kept popping of but rest seem fine. Anyone got part numbers for the losi cups and hpi ball studs?

losichris
20-11-2011, 11:01 PM
yep rear anti squat block ripped out ( not much impact) and cups pop off all the time, very soft plastic !!

jamiekerr14
20-11-2011, 11:03 PM
Losi HD ball cups with HPI-75115 and HPI-7116 ball studs

JohnM
21-11-2011, 12:47 PM
the HD ball caps pop off all the time on the 210 and the 410 v3 any one else had probs or is it just my bad driveing lol :woot:

I can't say about the 210, but since fitting the HD ball cups to my 410, I've only had them pop off once, and that was in a crash that would've took the entire front end off most cars.

Big G
21-11-2011, 01:37 PM
still yet to pop a HD ball cup off on either the 210 or the 410. :)

andys
21-11-2011, 01:59 PM
Had a few big crashes indoors with mine, not broke a single thing.
It's certainly a strong car IMO.

AmiSMB
21-11-2011, 03:20 PM
Had loads of spares with me for the 210 at the MK GP expecting some breakages and had none. I have already put Losi ball cups on and Schumacher ball studs on the steering :thumbsup:

dobber
20-01-2012, 11:38 AM
Had loads of spares with me for the 210 at the MK GP expecting some breakages and had none. I have already put Losi ball cups on and Schumacher ball studs on the steering :thumbsup:

Any idea on a part number or dimension for the Schumacher ball studs for the steering. Mine ball cup pops off the ball stud at the slightest tap.

Big G
20-01-2012, 11:48 AM
Broke my steering rack last week during a awkward landing. replaced with Atomic Carbon version :)

AmiSMB
20-01-2012, 02:36 PM
I have bought loads of spares and still am waiting to use any of them. No breakages at MK GP nor at Area 51 so maybe I am going to break loads at Offroad wars :o, I think not, seems to be as tuff as old boots!

jamiekerr14
20-01-2012, 02:53 PM
I have about 80% of the plastics brought as spares and have used 0

Only gripe I have had-Was ball cups-Changed
Rear tower-Replaced with Carbon

Car has been faultless so far

Gunthar Guntharsėn
20-01-2012, 08:33 PM
I haven't broken a thing after 3 months and I haven't had a transmitter in my hands for over 10 years before buying the 210. Ballcups have been good until a couple of weeks ago, then suddenly they started popping off all the time. I just changed to rpm ballcups and tc5 studs.

Everything on my car is box stock (except now the ballstuds en cups). Original thrust bearing and diff balls. I haven't even taken the diff apart since building it and it's still smooth as butter.

:)

acorn28
22-01-2012, 08:21 PM
First breakage this afternoon, rear tower went after giving the car an absolute hammering all day due to my inability to clear a double. I cannot fault this car, thumbs up to Durango :thumbsup:

TARTMAN
22-01-2012, 08:50 PM
a fellow TORCH'r, broke the rear side casing from the gearbox/rear end, damn it was a major reaqr strip down to repair it.
but all done and he went on to do well....

love the look and design of the rango, but sticking the schumy way for now....

Happy racing.........

sparrow.2
22-01-2012, 09:14 PM
....

AmiSMB
23-01-2012, 08:47 AM
a fellow TORCH'r, broke the rear side casing from the gearbox/rear end, damn it was a major reaqr strip down to repair it.
but all done and he went on to do well....

love the look and design of the rango, but sticking the schumy way for now....

Happy racing.........

This usually happens when not using the Durango HD ballends and ball studs. Best get a CF camber link from Nick Gurnell which will fix the problem :)

Gareth J
23-01-2012, 11:30 AM
Just a rear tower here.

jonathan may
23-01-2012, 01:09 PM
I had a carbon link plate on my 210 at torch yesterday lasted 2 laps in practise before snapping from brushing a pipe

triplesix
25-01-2012, 03:47 PM
A carbon rear tower broke, when another car crashed into mine. Other than that I only bent a rear outer hinge pin and stripped a servo horn (the Savöx 1251 is still fine, btw). Ballcups popped off only two or three times, but will be replaced soon. When I removed the ball diff, I noticed some more than normal worn out outdrives. I replaced the diff with a SC10 gear diff anyway...
I'm running on a fast indoor carpet track, so when crashes happen, they usually happen at relatively high speeds. So far nothing to complain about in terms of durability.
:thumbsup:

slowjun
26-01-2012, 09:07 AM
i think the gear case will be the first thing to give in, thats why i created a G10 brace, similar to Nick ( Forum member here) Rear Camber link CF. will try to post some pics, aside from that just had some Ball cups popping out, will be needing to change to Losi HD cups and some TC5 studs. Also fabricated my own steering links as the plastic ones are weak. Rear and Front towers will definately be replaced. Using SC10 Gear Diffs ( still have the full Ball Diff in Plastic), and oh , also using the Losi 25T Savox allu Horn, rimmed out the thread to fit in the TD steering stud. a Rear allu pivot is a must, still waiting from Tresrey/RDRP or on here to become available.

Skye
26-01-2012, 10:12 AM
I know this has been discussed to the death on here but what ball studs do I need to purchase. Can anyone give me comprehensive lists of part numbers required please?

I have purchased RPM ball cups, both short shank and long shank so just need to know what ball studs I need to buy to use with them. I assume I will need different lengths as they are not all the same on the kit, but just dont know what I need? :eh?:

To be fair I havent had one pop off in a race yet and I have used it for two meetings, but they frustrate the hell out of me trying to adjust them. To try and stop them popping off when adjusting I used some black thrust grease on the threads, but now that has resulted in the thread slipping inside the ball cup so it gets to a point and wont tighten anymore, it just slips the thread and spins.

Gunthar Guntharsėn
26-01-2012, 12:04 PM
I know this has been discussed to the death on here but what ball studs do I need to purchase. Can anyone give me comprehensive lists of part numbers required please?

I have purchased RPM ball cups, both short shank and long shank so just need to know what ball studs I need to buy to use with them. I assume I will need different lengths as they are not all the same on the kit, but just dont know what I need? :eh?:

To be fair I havent had one pop off in a race yet and I have used it for two meetings, but they frustrate the hell out of me trying to adjust them. To try and stop them popping off when adjusting I used some black thrust grease on the threads, but now that has resulted in the thread slipping inside the ball cup so it gets to a point and wont tighten anymore, it just slips the thread and spins.

I just rebuilt mine with rpm cups and 10mm tc5 ballstuds. Part number is 31285.

Skye
26-01-2012, 12:18 PM
I just rebuilt mine with rpm cups and 10mm tc5 ballstuds. Part number is 31285.



Thanks very much, I will get some ordered! :thumbsup:

MarkLeeds
27-01-2012, 08:42 AM
Bearing 601022 that holds the slipper shaft in place inside the gearbox case. Stripped a couple of spurs before I noticed the problem :thumbdown:

DEXtrain
27-01-2012, 06:09 PM
One rear tower and a couple of front wishbones , I admit some damage where the spur cover screw bolts on motor plate but I re-tapped .Everything ok since then