View Full Version : Durango DEX210 rear carbon camber link plate
Durango DEX210 rear carbon camber link plate
http://farm8.staticflickr.com/7001/6648905547_62cf1fcecf.jpg
Hi all I have been testing a new rear camber link plate for the last month or so along with a couple of other people. We have found it to give a lot better balance to the car on high grip tracks in the mid motored configuration! Helps the rear end not to collapse in the corner as much due to being able to run a shorter link! You do have to Dremel the old mount off the gearbox but the new plate has the standard hole in as well. It should also fit the rear motored setup but I have not had time to try this yet but will over the weekend. I will be making a batch next week and want to gauge some interested in the part. They will be £7.50 posted if you are interested in one could you Pm me
http://farm8.staticflickr.com/7028/6648903969_7766603db7.jpg
http://farm8.staticflickr.com/7008/6648898487_b4796aebfb.jpg
http://farm8.staticflickr.com/7008/6648893105_7ba8711cb2.jpg
http://farm8.staticflickr.com/7015/6648894905_12f10beb24.jpg
av4625
06-01-2012, 09:05 PM
i saw a guy using a schumacher one so this should be a good job?
Yeah a couple of ex schumacher guys saw my plate and then said an sx3 one might fit. I think you have to bolt it on top and mount the ball stud on the underside. But I could be wrong to be fair.
slowjun
09-01-2012, 08:20 AM
hope you can confirm if this will fit for RM configuration and also pics.. then it'll be great.
thanks.
Hi i am going to try it tonight so will let you know tomorrow
slowjun
12-01-2012, 07:04 AM
Hi i am going to try it tonight so will let you know tomorrow
Hi Nick,
hope you can share some pics for this product in Rear Motor Config, (will combine mine with the rear tower) :D
mark christopher
12-01-2012, 08:32 AM
i have a picture of eugene gallys with what looks like a schumacher part on, did not know till i read this..
slowjun
13-01-2012, 02:41 AM
From Amain (http://www.amainhobbies.com/product_info.php/cPath/1_25_1462_2096/products_id/153260/n/Schumacher-CF-Link-Mount-Rear-375mm) , i thought so too when i was browsing Amain.
http://i778.photobucket.com/albums/yy64/slow_jun/DEX%20210/schu3443.jpg
OneKiwi
16-01-2012, 06:57 PM
get any testing done?
kartstuffer
20-01-2012, 10:49 AM
Just tried this rear link last night and it really locked in the rear of the car and made it much more consistent to drive (and faster), don`t get the rear grip roll that was there and can push the car much more.
Excellent upgrade.
Used 2nd hole out on hub & 2nd hole in on plate.(from centre of link).:thumbsup::thumbsup::thumbsup:
slowjun
02-02-2012, 09:00 AM
Hi i am going to try it tonight so will let you know tomorrow
Hi Nick,
will these work for RM configuration? any pics?
thanks,
Jun.
Hi yes it fits the rear motor but i forgot to take a pic will try and do it this weekend
Nick
slowjun
02-02-2012, 09:48 AM
Hi yes it fits the rear motor but i forgot to take a pic will try and do it this weekend
Nick
great, also do you hava the rear cf towers available? to save on shipping. ;-)
sending PM.
Just to say thanks for all the order and thay have all just been post sorry for delay
kwiksi
05-02-2012, 10:11 PM
Hi yes it fits the rear motor but i forgot to take a pic will try and do it this weekend
Nick
Pics?
sorry will try and fined time to swop my car to rear motor tomorrow night
TDMAK
09-02-2012, 02:53 AM
Sent paypal, when will the parts ship? This part is very nice looking!! Cant wait
I sent some yesterday and the rest are going tomorrow
Cream
16-02-2012, 09:09 PM
PM sent...
PM sent...
snap :thumbsup:
Fernandez
17-02-2012, 08:53 PM
when will we see pictures when running this fantastic piece RM config ?
Sorry for delay i will try and find time to change to rear motor in after i have ran the car on Sunday
Jarred King
18-02-2012, 10:44 PM
i have received mine and trying to work out how to fit it in RM config.
Do i need to shave off the ears on the diff casing?
yeah you have to remove the old camber mounts all the way back to the diff bearing mounts if that make sense
slowjun
20-02-2012, 09:02 AM
i have received mine and trying to work out how to fit it in RM config.
Do i need to shave off the ears on the diff casing?
Hi Jarred,
Can you post some pics after installing? would be nice for us planning to get one also..
thanks,:thumbsup:
MatJohnson
26-02-2012, 03:52 PM
Nick, what size screws are in the chassis to replace the one going through tthe roll bar?
not got my car here at the moment but im guessing around 16mm but will check and Pm you tomorrow
TonyM
29-02-2012, 10:37 PM
Great, just fitted the plate. Now, because the plate provides different hole settings to the standard, it's no longer possible to do a direct comparison to the set-up sheets where the drivers are using the standard gear cover position. So, I was wondering what hub/plate positions people are using for different conditions, in particular:
1. Carpet mid traction?
2. Astro wet low traction?
3. Astro dry high traction?
In general, am I right in assuming that you use a shorter link to get more lateral grip, e.g. in lower traction situations? looking at other posts and links some seem to suggest this, but then some suggest you get sudden break away's which are more difficult to control.
Also looking at AE's RC cheat sheets it suggests short links for medium grip and long for high grip situations, but then goes on to say 'The longer the link, the less camber change, and the more traction. The shorter the link, the more camber change, and the less traction'. Confused - don't we need more traction in low traction situations?
Now, adding removing washers under the plate ball. Is this doing exactly the same as shortening/lengthening the link, or is there a subtle difference in the effect because of the change in the link angle?
Finally, if I maintain the same length of link but move it in/out on both the hub and plate to keep the same camber setting, is there any difference in the effect?
You can tell I'm totally messed up on this one.
AmiSMB
01-03-2012, 03:55 PM
From what I have read when you raise the ball stud height you are lowering the roll centre and when lowering the ball stud you end up with a higher roll centre. The camber link plate allows you to do this as I did read somewhere alot of people wanted to lower the ball stud and were taking plastic off of the gearbox to accomodate this but it is a weak area even before you take any plastic off.
Just to say many thanks for all the orders and they have all been posted today :thumbsup:
hotrodchris
20-03-2012, 09:12 PM
Nick pm sent:thumbsup:
Nick, do you still sell these plates?
Your Mailbox is full, was unable to send you a pm.
Thanks
Frank
RCAshers
03-08-2013, 04:54 PM
Nick you need to empty your inbox mate
jayropes
03-08-2013, 05:41 PM
Nick, if you have any more going could you send me you details and i'll send you the dosh!!
after you empty your inbox that is!!
Cheers Jay
peetbee
07-08-2013, 03:10 PM
Looking at his profile the Last Activity was: 09-11-2012
slippy
07-08-2013, 03:32 PM
Nick, if you have any more going could you send me you details and i'll send you the dosh!!
after you empty your inbox that is!!
Cheers Jay
You could go for the tresrey option which is very similar if not slightly nicer.
Dave.
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.