PDA

View Full Version : Speed Passion Motor Problems

aH0tUnicorn
22-02-2012, 05:11 PM
Hi,

Ive got a sp motor which will only work when you push it. i have changed the connection shields and changed the sensor wire. when it stops the motor wont run again unless you push it again.


Thanks
Fletch248
22-02-2012, 06:10 PM
does the motor work fine senseless?
aH0tUnicorn
22-02-2012, 06:13 PM
does the motor work fine senseless?

Its not a sensorless motor its a v3.
Fletch248
22-02-2012, 06:16 PM
sent u a pm dude
Dudders
22-02-2012, 06:18 PM
Are the 3 plugs in fully and not able to wiggle?
Fletch248
22-02-2012, 06:25 PM
personal i think its the internal board in the motor
aH0tUnicorn
22-02-2012, 06:28 PM
Are the 3 plugs in fully and not able to wiggle?

yeah they can move allitle.
aH0tUnicorn
22-02-2012, 06:29 PM
personal i think its the internal board in the motor

how can i change or fix this
Fletch248
22-02-2012, 06:56 PM
Im not saying for def that this will fix it but i had one that did the same thing (ish)

Here is the part number SPSB218
aH0tUnicorn
22-02-2012, 10:19 PM
Im not saying for def that this will fix it but i had one that did the same thing (ish)

Here is the part number SPSB218




thanks ill give that a try.
aH0tUnicorn
23-02-2012, 10:37 AM
Ive got my friends 7.5 to work with my sensor borard so i can run it now :D
mattybucks
23-02-2012, 10:45 AM
You can get the motor tester from Schumacher. Tom was testing a motor last night with one, simple but effective.

The motors probably a shorting out.
Big G
23-02-2012, 11:06 AM
I had a SP motor that wouldn't move from a standstill, but if you gave it a nudge and didn't let it stop it would run fine.

Turned out to be 1 of the phases on the speedo (SP GT2.0 LPF) had gone down. It was replaced by Schumacher under warranty.
aH0tUnicorn
23-02-2012, 01:04 PM
You can get the motor tester from Schumacher. Tom was testing a motor last night with one, simple but effective.

The motors probably a shorting out.

Ive been incontact with schumacher and im going to ask if i can send my motor in to be tested to get it sorted out
aH0tUnicorn
23-02-2012, 01:07 PM
I had a SP motor that wouldn't move from a standstill, but if you gave it a nudge and didn't let it stop it would run fine.

Turned out to be 1 of the phases on the speedo (SP GT2.0 LPF) had gone down. It was replaced by Schumacher under warranty.

yeah but if i tp or crash then it wont move. im just gunna send it too schumacher to be fixed.
imull
23-02-2012, 06:34 PM
Needing a nudge is almost always the speedo. Have you tried another motor on it?
Browny_37
27-02-2012, 08:49 PM
I had a SPEC Novak Speed Controller I intended to use for the wet car last year, I had the issues where the car would need a nudge to make it move..I thought this may have been the motor. As it wasn't a good quality brushless motor that was paired with it originally. Soldered a GM10.5 on and gave it a test run, accelerated fine...hit the brakes and the speedo went up in a huge puff of smoke, which in turn melted the top PCB to the lower one.