oOple.com Forums

oOple.com Forums (http://www.oople.com/forums/index.php)
-   Vintage RC (http://www.oople.com/forums/forumdisplay.php?f=48)
-   -   Questions on the Bosscat/brushless (http://www.oople.com/forums/showthread.php?t=118138)

Martin Wallace 30-12-2012 09:35 PM

Questions on the Bosscat/brushless
 
is anyone running one with a brushless motor if so can you answer the following.

1. which mods have been done to the slipper/belts/motor plate if any.
2. what brushless motor limit/turn are you running in the car with mods or without mods.
3. has it been running without problems on either of the above.

thanks guys.

Martin Wallace 01-01-2013 01:07 PM

Quote:

Originally Posted by Martin Wallace (Post 727075)
is anyone running one with a brushless motor if so can you answer the following.

1. which mods have been done to the slipper/belts/motor plate if any.
2. what brushless motor limit/turn are you running in the car with mods or without mods.
3. has it been running without problems on either of the above.

thanks guys.


Anyone?, i saw one running at the oople race, im sure it was stu,s.

gainsy 01-01-2013 01:31 PM

It was my bosscat at the oople event, i was using a 9 single brushed motor with a lrp esc & orion lipo
Right if your going brushless then you will deffo need the slipper clutch fitted, mine also had 4 disc spring washers fitted to each diff, these are essential to stop the diffs undoing, they are not shown in the manual but are shown in the procat manual, if you can find some then alloy diff washer carriers would be a very good idea, i melted the plastic ones with the brushed motor
If you stick the extras on then brushless shouldn't be a problem but i wouldn't go mad, maybe a 8.5-10.5t
Hope that helps Martin

kaszal 01-01-2013 08:45 PM

Good advice! Stu's identified the most important and practical upgrades. Also check that the belts/diffs are tensioned correctly and that the old bearings are nice and free.

There's loads more ideas in my main thread :)

My Procat did well with 6.5T but I'm going down to 10.5T in the hope it will be easier to drive (for me) and preserve my spares for longer ;)

http://www.youtube.com/watch?v=PZIkSMEYosQ

Dazzieboy 02-01-2013 12:18 PM

I would also note that is can be surface dependant. I was running an 8.5T in my procat on carpet and was getting belt skip. I had to run the slipper very free and not be brutal with the throttle. I'm investigating having some new rear drum diffs made at the moment, when I get some proper details I will post something up.

Martin Wallace 03-01-2013 09:16 PM

Quote:

Originally Posted by Dazzieboy (Post 728024)
I would also note that is can be surface dependant. I was running an 8.5T in my procat on carpet and was getting belt skip. I had to run the slipper very free and not be brutal with the throttle. I'm investigating having some new rear drum diffs made at the moment, when I get some proper details I will post something up.


thanks stu, i had fitted the brushless motor in place atm but it seems i might have to extend the motor slots longer to achieve more purchase for variation sizes for pinions? not sure if you had such a problem as you were running a brushed mod.

4 disc spring washers & alloy diff washer carriers.can these still be gotten?

kaszal :- yes mate everything is free and running well as the car was rebuilt. i was hoping to give it a go on grass maybe with an 8.5t.

as for holding in lipo saddles what would be best. maybe ae pillars and carbon straps with the thumb screws?.

also my main concern is the wheel hexes on the rims, im sure back in the day when i did run my bosscat i stripped a few of these, i cant imagine what they would be like now, but i guess it will be getting the diffs and slipper adjusted bang on for this.

thanks guys

kaszal 04-01-2013 09:23 AM

The original 1/8" disc springs are hard to find but you can use U857 instead. They are bigger so you won't be able to fit the dust caps unless you use Big 6 outdrives. However bear in mind they will also affect the driveshaft length...

http://www.oople.com/forums/showpost...1&postcount=87

The castle adaptors on the hubs are fine if they're undamaged and lined up correctly. I inserted crush spacers so the wheel bolts could be done up more securely without the bearings binding...

http://www.oople.com/forums/showpost...&postcount=164

Yes, the motor position is limited. Different spurs will help.

I designed my own straps and trays...

http://www.oople.com/forums/showpost...&postcount=648

Martin Wallace 07-01-2013 05:42 PM

Quote:

Originally Posted by kaszal (Post 728778)
The original 1/8" disc springs are hard to find but you can use U857 instead. They are bigger so you won't be able to fit the dust caps unless you use Big 6 outdrives. However bear in mind they will also affect the driveshaft length...

http://www.oople.com/forums/showpost...1&postcount=87

The castle adaptors on the hubs are fine if they're undamaged and lined up correctly. I inserted crush spacers so the wheel bolts could be done up more securely without the bearings binding...

http://www.oople.com/forums/showpost...&postcount=164

Yes, the motor position is limited. Different spurs will help.

I designed my own straps and trays...

http://www.oople.com/forums/showpost...&postcount=648


thanks for your advice and help, its greatly appreciated kaszal.


All times are GMT. The time now is 10:15 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2026, vBulletin Solutions, Inc.
oOple.com