oOple.com Forums

oOple.com Forums (http://www.oople.com/forums/index.php)
-   Schumacher (http://www.oople.com/forums/forumdisplay.php?f=46)
-   -   rear drop (http://www.oople.com/forums/showthread.php?t=26691)

restimax 06-07-2009 09:48 AM

rear drop
 
in the cat, what the best mod to have more drop at the rear?;)

Swiss 06-07-2009 09:55 AM

I use the turnbuckle rod ends instead of the std short ones on the bottom of the shock. And a 3/4qtr one on the front.

P

mikeyscott 22-09-2009 06:04 PM

I'm looking at doing this too.

How many people are running with the different cups?

bigred5765 22-09-2009 06:32 PM

we have always run them its worth doing,and try to run as small amount of washers at the rear to lift the wishbone high,

mw02veg 22-09-2009 06:44 PM

On Grant’s car total front shock length 85mm with a ¾ length ball stud and on the rear total shock length 99mm with a full length ball stud.



Mike

mikeyscott 23-09-2009 04:31 PM

Quote:

Originally Posted by mw02veg (Post 289870)
On Grant’s car total front shock length 85mm with a ¾ length ball stud and on the rear total shock length 99mm with a full length ball stud.



Mike

.75 of an inch then on the rear shocks?

discostu 23-09-2009 10:20 PM

Quote:

Originally Posted by mw02veg (Post 289870)
On Grant’s car total front shock length 85mm with a ¾ length ball stud and on the rear total shock length 99mm with a full length ball stud.



Mike

hey mike

how much weight is grant running

bigred5765 23-09-2009 11:26 PM

we run about the same weight.108grms if i remember right,

eichkay 24-09-2009 12:03 AM

Quote:

Originally Posted by bigred5765 (Post 290392)
we run about the same weight.108grms if i remember right,

Im rather new to the schey, where is the weight located ? front bia's, rear bia's ... 50/50 ?? also is this weight to make the car legal at the events or required for better handling ?

MHeadling 24-09-2009 07:52 AM

What's the part number for the 3/4 lengh ball links ?

I'm interesed as to what weight the the team run too?

niggs98 24-09-2009 08:07 AM

there isnt a 3/4 lenth ball joint. get the longer ones for the turnbuckles and cut them to the desired lenth

Mossy 24-09-2009 08:13 AM

Nath is right, just cut them down to the correct size. As for weight, for me it varies depending what track im at. I know Grant is pretty steady around the 108g mark, but at Worksop and the Euros i didnt run any. I prefer a more lively car than Grant, so comes down to what you like really.

Positioning the weight, when I don run some its under the chassis as central as possible. The weight distribution on the car is fine so no need to run it to the front or back.

Si

mikeyscott 24-09-2009 09:00 AM

Quote:

Originally Posted by niggs98 (Post 290436)
there isnt a 3/4 lenth ball joint. get the longer ones for the turnbuckles and cut them to the desired lenth

Ah ok, I'll look into that, need to get out the measuring tools..

Think it's .75 for the full length ones.

Surprised they haven't released new cups as option parts etc.

bigred5765 24-09-2009 09:42 AM

for positioning on Matty's car i never move it, but as Si said we did remove ours for the euros,but back in the UK we haven't removed it yet but we also haven't run ares indoors yet, ill attach a pic of ours,it'll have to be a bit later flat battery:thumbdown:

Northy 24-09-2009 10:13 AM

"ours" ;) :p:p:p:woot::woot::woot::thumbsup::thumbsup::thumb sup::):):):):wub:wub:wub

Love you Lion-o

bigred5765 24-09-2009 10:26 AM

Quote:

Originally Posted by Northy (Post 290492)
"ours" ;) :p:p:p:woot::woot::woot::thumbsup::thumbsup::thumb sup::):):):):wub:wub:wub

Love you Lion-o

corrected SIR,

mikeyscott 24-09-2009 01:20 PM

Measured the ballcups and the turnbuckle ones are about 19mm and the standard ones are about 14mm.

3/4 of the turnbuckle ends is 14.25mm

niggs98 24-09-2009 02:04 PM

not quite..... as you have long and short there make the 3/4 ones half way inbetween ie aprox 16.5-17mm

bigred5765 24-09-2009 03:46 PM

just measured mattys ball joints for ya mikey,
long =19mm
3/4 = 16.5mm
short = 14mm

mikeyscott 24-09-2009 04:06 PM

Quote:

Originally Posted by bigred5765 (Post 290617)
just measured mattys ball joints for ya mikey,
long =19mm
3/4 = 16.5mm
short = 14mm

Cheers :D


All times are GMT. The time now is 07:18 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2026, vBulletin Solutions, Inc.
oOple.com