oOple.com Forums

oOple.com Forums (http://www.oople.com/forums/index.php)
-   Electrics (http://www.oople.com/forums/forumdisplay.php?f=26)
-   -   Wires on charger (http://www.oople.com/forums/showthread.php?t=34092)

ashleyb4 12-11-2009 12:32 AM

Wires on charger
 
Hi Guys

Ive got my trsuty Orion advantage charger that ive had for about 4 years now. Now on the charge leads it has the main wires red and black then two smaller wires that run along side of them them white for red and blue for black. what purpose do these serve?

A

Southwell 12-11-2009 01:04 AM

Temp?

sparrow.2 12-11-2009 05:56 AM

Some chargers have separate leads to measure voltage through. It gives more accurate readings than the wires where the heavy amp load is going through.

ashleyb4 12-11-2009 10:51 AM

No its got a seperate temp probe thing. Never use it mind.

Sparrow i was thinking somewhere along the same lines.

cheers

A

super__dan 12-11-2009 12:42 PM

They are seperate voltage sensing leads and I beleive and are calibrated to length so don't cut them short. Incidentally I did a little measuring of true voltage against what chargers thought the voltage was and the Orion advantage was the most accurate (some of the cheap Lipo ones were miles off :( ) which is why I now use 2 advantages as my Lipo chargers!

ashleyb4 12-11-2009 12:59 PM

You see i have a V balance now which i was hoping to use with my advantage. Will I be able to use it?

A

jono83 12-11-2009 01:28 PM

yes ash you jus use it inline between your lipo and charger

Col 12-11-2009 02:07 PM

Quote:

Originally Posted by super__dan (Post 309159)
They are seperate voltage sensing leads and I beleive and are calibrated to length so don't cut them short. Incidentally I did a little measuring of true voltage against what chargers thought the voltage was and the Orion advantage was the most accurate (some of the cheap Lipo ones were miles off :( ) which is why I now use 2 advantages as my Lipo chargers!

My robotronic charger says it's charging at 4.9amps, but my pro peak power supply says it's only supplying around 4.0amps. I've often wondered which one I should believe.

super__dan 12-11-2009 04:58 PM

That's different Col, you're power supply is giving out [email protected] = 55W of power, your charger is using [email protected] = 41W, the difference being loses of heat, the screen power etc etc.

Ash - I use a V balance on both my chargers (1 for each) and only by rare exception don't balance charge. I have male connectors on the Advantage leads, females in the in end of the balance and then males on the other to go into the cells.

The only thing this does on mine is a slight error (safe though) meaning where as 8.40V on the charger used to be 8.40V at the cells, it's now 8.37V on the cells when the charger thinks it's 8.40V. This means I'm always OK at scrutineering, though technically they are probably only 99.9% charged ;)

The worst one I saw was a cheap one with internal balancing that overcharged by 0.15V, now many may think this is OK and I don't really know but I do know this would fail scruitineering. This is why you still very much get what you pay for with chargers. I'm not saying the Orion is THE best in the worls but it's a decent one IMHO.

Col 12-11-2009 05:57 PM

head
Baffled
over
my
science
by


All times are GMT. The time now is 07:11 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2026, vBulletin Solutions, Inc.
oOple.com