Go Back   oOple.com Forums > Search Forums

Showing results 1 to 25 of 500
Search took 0.03 seconds.
Search: Posts Made By: pugs
Forum: Team Associated 28-12-2018
Replies: 3
Views: 327
Posted By pugs
Iv used the gear diff with 4K and 2 gears but tbh...

Iv used the gear diff with 4K and 2 gears but tbh the ball diff was faster for me and actually felt safer...I would go for 2 gears with the kit diff oil and see how it feels...mind this was in the b6...
Forum: Wanted 29-05-2018
Replies: 0
Views: 106
Posted By pugs
Losi 35wt shock oil ( orange )

As above if anyone has some please:) half bottles or anything...
Forum: Wanted 15-03-2018
Replies: 2
SORTED! Sold
Views: 250
Posted By pugs
there is a schumacher k2 in the for sale section...

there is a schumacher k2 in the for sale section at £180 and a one at £150...
Forum: Electrics 06-03-2018
Replies: 1
Views: 284
Posted By pugs
Fairly sure it will as they are hobbywing based,...

Fairly sure it will as they are hobbywing based, unplug the sensor lead to try, 98% sure it will;)
Forum: Electrics 19-10-2017
Replies: 1
Views: 380
Posted By pugs
I am sure you will be able to clear the memories,...

I am sure you will be able to clear the memories, you could on the old super exzes....
Forum: Electrics 13-10-2017
Replies: 3
Views: 469
Posted By pugs
Sounds about right to me:)

Sounds about right to me:)
Forum: Electrics 22-08-2017
Replies: 2
Views: 460
Posted By pugs
which version? i fix electrics;)

which version? i fix electrics;)
Forum: Wanted 21-08-2017
Replies: 1
Views: 184
Posted By pugs
Have a word with Ben on here, I think he will be...

Have a word with Ben on here, I think he will be going there:)
Forum: Wanted 14-07-2017
Replies: 0
Views: 174
Posted By pugs
Novak gtb2 or kinetic

As above, not bothered on condition long as it works and cheapish:lol: please pm any offers:)
Forum: North East 12-06-2017
Replies: 20
Views: 1,701
Posted By pugs
I am not on the committee, but I have spoke to...

I am not on the committee, but I have spoke to one committee member and camping and caravaning is fine
Forum: Electrics 06-06-2017
Replies: 6
Views: 551
Posted By pugs
You cant fix fet boards in modern...

You cant fix fet boards in modern speedo's.....you can get the fets no problem, you just cant remove the old ones, there is that much copper around them it takes the heat away from the fet you are...
Forum: Electrics 05-06-2017
Replies: 6
Views: 551
Posted By pugs
If it stutters or wont turn the motor with out...

If it stutters or wont turn the motor with out helping it then the fet board will be blown and its for the bin:(
Forum: Electrics 25-05-2017
Replies: 8
Views: 469
Posted By pugs
When I used them I took them out and resoldered...

When I used them I took them out and resoldered them in vertical;)
Forum: Electrics 07-05-2017
Replies: 2
Views: 270
Posted By pugs
I would rather go higher on the micro farads ( uf...

I would rather go higher on the micro farads ( uf ) rather than lower so replace it with 470uf or higher, trying to keep the voltage rating the same, if not go slightly higher on the voltage rating...
Forum: Electrics 02-05-2017
Replies: 79
Views: 11,392
Posted By pugs
I agree....the fets are actually simlar spec, but...

I agree....the fets are actually simlar spec, but the lack of them is going to generate some heat very quickly:lol:
Forum: XRAY 11-04-2017
Replies: 2
Views: 1,625
Posted By pugs
I would say 25 or 26 for a 7.5t motor :)

I would say 25 or 26 for a 7.5t motor :)
Forum: Electrics 11-03-2017
Replies: 3
Views: 292
Posted By pugs
Going off just a picture i would say 14 gauge mate

Going off just a picture i would say 14 gauge mate
Forum: Electrics 07-03-2017
Replies: 4
Views: 647
Posted By pugs
will do mate, its a sanwa handset with the frsky...

will do mate, its a sanwa handset with the frsky hack:)
Forum: Team Associated 09-01-2017
Replies: 5
Views: 1,163
Posted By pugs
When you build it to the book it shows the ball...

When you build it to the book it shows the ball stud on the alloy rear brace on the outer hole, it then shows it in the middle hole later on, but if you look at the kit set up sheet at the back of...
Forum: Team Associated 01-01-2017
Replies: 3
Views: 532
Posted By pugs
I would guess at an m2 of some sort mate, try a...

I would guess at an m2 of some sort mate, try a suspension pin retainer screw and see if the thread fits, they are m2, if it fits in then its just a case of measuring the one you do have for length:)
Forum: Team Associated 19-12-2016
Replies: 11
Views: 2,226
Posted By pugs
I believe the shock towers are slightly different...

I believe the shock towers are slightly different for the flat arms as well.....
Forum: North East 29-07-2016
Replies: 15
Views: 2,111
Posted By pugs
I think this is it mate: Grangefield...

I think this is it mate:


Grangefield Youth & Community Centre
Oxbridge Lane
Stockton
TS18 4HY
Forum: Electrics 17-06-2016
Replies: 3
Views: 457
Posted By pugs
Short answer.....yes :)

Short answer.....yes :)
Forum: Electrics 17-05-2016
Replies: 10
Views: 1,009
Posted By pugs
Option 1 for me, but I am an electronics...

Option 1 for me, but I am an electronics engineer:)
Forum: Electrics 05-05-2016
Replies: 13
Views: 863
Posted By pugs
Its the servo, common problem, use ko or sanwa;)

Its the servo, common problem, use ko or sanwa;)
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT. The time now is 11:14 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
oOple.com