|
|
#1
|
|||
|
|||
TRF511 Upgrade Set (#84315) Parts Availability
Update 02 April
So to save others some time I thought I'd summarise my findings having spent a little time on web and phone looking into this. Problem I needed individual kit parts from the TRF511 Upgrade Set (#84315), belts and pulleys in my case however this adventure applies to all 1 vehicle parts in the kit (i.e all the bits for this kit alone). Findings They're not available from Tamiya Japan. There's no indication that they will be made available in the future but you'd hope it was likely. There has been no mention of a future release which probably means that if they do come it will be August or later. Apparently there have been similar occurrences in the TC world with the ball diff pulleys being a culprit there too. On that note it does appear as if the TA06 ball diff pulley (39T) will fit but neither is that available as a single part from Tamiya. The 37T pulley as an individual part evidently arrived some ten or more months after the full assembly! As a consequence there is an aftermarket for TC pulleys in Japan (and elsewhere I suppose) because apparently the drift guys eat through them, I have no idea. Reading around (mostly Japanese sites) these are a credible replacement: Link: Eagle Racing 39T Delrin TA06 Solid/Ball Diff Pulley (DP01-39T) I can't personally recommend these yet, I've ordered a handful because they're inexpensive and will report back when I get them (and sell some if they're okay). If you need a new belt, chassis, diff joints, or any of the alloy bits from the set as individual parts then you're stuffed for the time being. Conclusion I purchased a handful of aftermarket pulleys (see above) and also a NIP Upgrade Set (thanks Kennith). I'd hate to need another complete set when they're out of stock again and who knows if there'll be another run. Hey, they may just be withholding individual spares for suckers like me but it's a PITA! Hope that helps someone, Dave --- Original Message --- Hi there, I need new pulleys and belts for my 511 w/upgrade kit, has anybody had success sourcing them? (Warning: don't use aftermarket diff covers with the 39T pulleys, insufficient clearance if something does get in). I've tried my usual TRF stockist in Germany and they say the part numbers (8 digit from the Upgrade Kit manual) are not listed on the Tamiya Japan dealers site. They've never had a problem supplying me hard-to-find TRF parts in the past. It's a pretty useless upgrade it we can't get spares. I'm on the verge of buying another complete kit just to secure the parts which would sort-of suck. Any suggestions? Cheers. Last edited by djmcnz; 02-05-2013 at 06:11 PM. Reason: Updated with findings |
#2
|
|||
|
|||
Same as me: I want a spare of the new and big Axle Washer (#19804655) included in the 502X upgrade kit (#84310) but it is imposible to find it...
|
#3
|
||||
|
||||
54488 TRF201 Large Rear Axle washer (2 Pcs.)
|
#4
|
|||
|
|||
Can we use '54305 TA06 Front Ball Diff Set - 39T' (or rather the pulley from it) on the 511.1 does anyone know?
If so, is there a part number for the pulley alone? Any suggestions on belts? |
#5
|
|||
|
|||
Will the 369mm belts fit the larger 39 pulleys on the loosest setting on the cams?
|
#6
|
|||
|
|||
This could be what I want, thanks!
|
#7
|
||||
|
||||
Did you see this on ebay? Expensive, but kinda cool...
http://www.ebay.com/itm/Tamiya-TA05-...-/251173076944
__________________
HE>i |
#8
|
|||
|
|||
Yes, I did actually but only after I'd picked the the Eagle ones. Looks heavy to me... and I wonder about overall wear on the other diff components. Don't know myself.
As I said I picked up the Eagle ones and they've arrived, direct from Eagle in Japan. They even sent me a picture of the package and label before they sent it! Mind you shipping wasn't cheap so I averaged it out over a few. The quality seems fine, they're a little bit harder than the Tamiya ones and the teeth have a flatter, wider peak but the mesh to belt is perfect. We'll see how they go. |
#9
|
|||
|
|||
Quote:
PM me if you want it. I'm sure we can agree on a price. The pulley should be the same as in the TA06 front ball diff though.
__________________
http://kentech.blogs.se |
#10
|
||||
|
||||
http://www.modellbau-seidel.de/
German Tamiya webshop, who has pretty much everything and also sells pretty much everything seperately, things like the WO Universal Shaft cross joint parts (which is really nice as those shafts have an off diameter) and rear axle washers. It's not the cheapest store but to be fair Rene Seidel does have everything Tamiya you might need and postage has always been pretty quick in my experience (to the Netherlands, though to the UK can't take much longer). Only downside are postage costs, it's a flat rate, regardless whether you order one washer or a whole kit. The 19804655 axle washer is currently sold out, I'd just contact him and ask him about it |
#11
|
|||
|
|||
Quote:
Quote:
Quote:
|
#12
|
|||
|
|||
So I found these:
https://eagleonlineshop.com/eaglesho...px?id=DP01-39T My ability to translate Japanese is limited to Google and it's a little ambiguous as to whether it will work with the ball diff. Looks like it should though and they're not too expensive. Apparently this problem has affected the touring car crowd for quite some time so I'm not expecting it to change quickly. I still need a new kit if I want new belts! |
|
|