|
#1
|
||||
|
||||
S-Workz S12-1M setup's
I found this link on petit with the worlds setup
http://site.petitrc.com/setup/sworkz...WorkzS102.html
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#2
|
||||
|
||||
Setup sheet was also highly revamped.
|
#3
|
||||
|
||||
worlds setup is also in the manual
__________________
Stephen Smith Answer RC Team HB Racing | Team Orion | Xpert | Racing Experience |
#4
|
||||
|
||||
Southport turf wars r4 setup
This is my setup i ran at southport today, the track is two different types of astro on an indoor track
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#5
|
||||
|
||||
Lee check your Facebook messenger. I've sent you the link for your final yesterday
__________________
PR Insidelinemodels |
#6
|
||||
|
||||
Guys, any idea what teeth are on the diff gear on this car, is it 55? Ok just worked out its not 55.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS Last edited by Welshy40; 13-02-2016 at 08:50 PM. |
#7
|
||||
|
||||
not sure, time to get the tipex and start counting lol
__________________
Stephen Smith Answer RC Team HB Racing | Team Orion | Xpert | Racing Experience |
#8
|
||||
|
||||
Southport Easter egg race Wet Conditions
this is my setup fron the weekend at srcc
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#9
|
||||
|
||||
This is the setup i ran at bury on the 10th april track was damp at start of the day bur dried out near end of day
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#10
|
|||
|
|||
i saw you setup with rb6 ball diff so i got one to install. was not the easiest to put in but how did you get it in?
|
#11
|
||||
|
||||
Dremel the outdrives
__________________
PR Insidelinemodels |
#12
|
||||
|
||||
As Paul said you need to dremel the out drives and use about 4mm of shim a each side
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#13
|
|||
|
|||
i got it to work but i actually used vinyl tubing that had the same id as the od of outdrives and works perfectly. tube cost $.50 for 1'. car does awsome on clay with ball diff.
|
#14
|
||||
|
||||
One thing we have been doing is drilling Pistons we are at 1.7 all round at moment, bearing in mind we are running on astro we have found the car absorbs the bumps better and dousnt get out of shape as easily. Just go up 100 cost on oil so if you are running 350 rear go to 450
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#15
|
||||
|
||||
im running kit pistons still Lee, ive no drill so cant make them 1,7
i think Mark may still be on 1.6 front 1.7 rear Hayden ran my car at the nationals at kiddi like that with 500 front 450 rear and went well xray 3dot front xray 2dot rear Im going to try 2 dot front 1 dot rear at Bury tonight in a practice
__________________
PR Insidelinemodels |
#16
|
|||
|
|||
there are a few guys at the a main hobbies track that run the s12 and said to run 3x1.4 with 32.5w in front and 2x1.6 30w in rear. they say it works great on the high bite track they have. I will know next sunday, am going there again to test my sworkz 1/8 scales for the sworkz challenge and will hit up the outback track too for the s12. will give update.
|
#17
|
||||
|
||||
This is my setup from batley. Low grip very bumpy
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
#18
|
|||
|
|||
This is my Base setup for Dry Astro/Grass and Carpet. I will be giving this to all new Sworkz Team Drivers to use as a good starting point.
Mark Redmond. North/Northwest Team Manager
__________________
CML - AE - Hobbywing - Answer-RC - RossMod |
#19
|
||||
|
||||
This is my setup from today, i would say this is good starting point for a wet setup
__________________
Answer RC team driver Formby models HB Racing D216 HB Racing D418 www.kandmacoustics.co.uk |
|
|