|
#21
|
|||
|
|||
To Kym from Australia, I have received your payment and will send out a gear. Thanks
|
#22
|
|||
|
|||
|
#23
|
||||
|
||||
I would like to test a full set when you have done them.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#24
|
|||
|
|||
A few of you guys have been asking me about the Optima Mid B4 layshaft. I should get 4 ready by this week (1 is for myself). Will assemble in my own Mid then if all ok, will post pics here and up for sale .
|
#25
|
||||
|
||||
1 for Dan
|
#26
|
||||
|
||||
And the other Dan
__________________
___________________ Maxxum FF Ultima Pro Turbo Optima Mid SE Turbo Optima Mid SP Optima Mid Custom Special Lazer ZX Lazer ZX-R Lazer ZX-S |
#27
|
||||
|
||||
|
#28
|
|||
|
|||
|
#29
|
||||
|
||||
__________________
___________________ Maxxum FF Ultima Pro Turbo Optima Mid SE Turbo Optima Mid SP Optima Mid Custom Special Lazer ZX Lazer ZX-R Lazer ZX-S |
#30
|
|||
|
|||
mid Ot-85 and b4 topshaft
please let me know when you have one of each, for my mid
|
#31
|
|||
|
|||
layshafts are here. PEEK OT-85 also available but at $15 each shipped. Layshaft is $35 Shipped. DanB4, HKS TRD each booked one layshaft. Mid booked 1 layshaft and 1 PEEK middle gear. In the pic you see 4 shafts but I am taking one for myself . Will make more if there is demand. my paypal is alcyon2sp@gmail.com Also I will be making instructions on how to assemble this layshaft by this week. |
#32
|
|||
|
|||
Layshaft Assembly Instructions
Place the 2mm pin into the shaft. Insert the steel top gear. Clip the e clip. Slide the layshaft through the gearbox so that the slipper side comes out from the motor side. Slide in the 5x10 bearing into the gearbox. Place the idler pulley. Place the outer gearbox cover and the other 5x10 bearing, then e clip the shaft. Fix the motor Plate. Place the first B4 slipper plate all the way in. Place the spur gear with slipper pads glued thinly on the spur. Fit the outer slipper pad. fit the spring and the nut and tighthen. you will need to do adjustment at the track. Your slipper is now ready but you need to modify your gear cover to protect the long end. So I will give you this tube which I will cut. Basically you need to ream a hole at the center of the gear cover where the nut is, and then insert the tube. Make sure you don't ream too much, you need this to be a little tight fit. Place silicone sealant over the sides to seal the gear cover. Adjust the angle of the tube so that it is straight. Let the silicone glue dry overnight. After the silicone has dried, place superglue over the joint to stiffen it. How the gear cover looks like from the inside. |
#33
|
||||
|
||||
Payment sent
__________________
___________________ Maxxum FF Ultima Pro Turbo Optima Mid SE Turbo Optima Mid SP Optima Mid Custom Special Lazer ZX Lazer ZX-R Lazer ZX-S |
#34
|
|||
|
|||
I forgot to mention, you must fix your rear shocks backwards and flip you rear arms too. Because the right shock will get in the way of the new shaft. I recommend the use of a 81T spur as is it closest in diameter to the original Mid spur gear.
|
#35
|
||||
|
||||
Thats fine, I'm going to run a lazer tower and arms on the rear
__________________
___________________ Maxxum FF Ultima Pro Turbo Optima Mid SE Turbo Optima Mid SP Optima Mid Custom Special Lazer ZX Lazer ZX-R Lazer ZX-S |
#36
|
|||
|
|||
hey alcyon,
maybee an idea for the future, but i think on the team durango DEX 210 the spring is on the other side (so the gear and slipper plates and slipper pad on the original side and the spring for tightning it or adjusting on the other side of the car) see on a manual or pictures of the durango dex 210 . maybee that is a solution for not changing the arms and the shocks and maybee you don't have to modifie the gear cover..... regards, ken |
#37
|
|||
|
|||
Quote:
|
#38
|
||||
|
||||
Will the B4.1 slipper assembly fit or only the original B4?
Payment also sent |
#39
|
|||
|
|||
As long as its not VTS it should fit.
|
#40
|
||||
|
||||
Layshaft arrived in the mail today
__________________
___________________ Maxxum FF Ultima Pro Turbo Optima Mid SE Turbo Optima Mid SP Optima Mid Custom Special Lazer ZX Lazer ZX-R Lazer ZX-S |
|
|