|
#41
|
||||
|
||||
They look like the shock standoffs with blue nuts on
__________________
Schumacher K2 Schumacher KC Hobbywing XR10 Pro V4 - Xerun V10 - Sanwa - Highest HV www.racing-cars.com |
#42
|
|||
|
|||
the shock mounts?
had to find his facebook page to see a better image - presume its ooples servers reducing the res. though it is a new front top deck as it doesnt have the antenna mount on it - its now behind the servo. and given that a few drivers seem to be running the b5 balljoints, i wonder if this is heading towards a metric version of the car. |
#43
|
||||
|
||||
Cant see there ever being a metric b44 series, i can see blue at the bottom of the rear shock tower though ?
__________________
|
#44
|
||||
|
||||
They're front shock stand-offs Gaz as has been said.
__________________
Stevie Brew BW-RACING@HOTMAIL.COM http://www.oople.com/forums/showthre...hlight=stegger |
#45
|
||||
|
||||
I know the age old try it yourself statement but anyone come to conclusion on shorty or saddle yet?
Low grip which one? High grip which one?
__________________
B74.1 B6.4 BD7 15 Black Edition Shelf queens Losi XX4 Worlds, XX-CR Mid East Regionals - F3 Trader Feedback |
#46
|
|||
|
|||
B44.3 £265
Having run a dex410 for mostly 4 years thinking of a change and at £265 at mb models seems a bargain.
Whats the car like on high grip astro with this centre diff and how would it compare to a dex410 to anyone who may have owned both? |
#47
|
||||
|
||||
Never ran a durango but have a 44.3, centre diff on high grip is good as long as you run very high grade oil in centre, I run 10k/500k/7k and it goes very well
__________________
Schumacher K2 Schumacher KC Hobbywing XR10 Pro V4 - Xerun V10 - Sanwa - Highest HV www.racing-cars.com |
#48
|
||||
|
||||
__________________
Last edited by Noob; 27-01-2016 at 03:20 PM. |
#49
|
||||
|
||||
hi, this is an old thread but i have just built one of these and had to order some diff shims and now i can fit the bearings over, they are shiney not like the over size ones in the kit.
got the RPM arms but a bit confused how to secure the hinge pins, im guessing the screws provided go in the end to secure but don't want to damage them can anyone confirm this? |
#50
|
||||
|
||||
Quote:
Its for the SC10 but same principal https://www.youtube.com/watch?v=vnk7tSBuj1M
__________________
AKA Dexter Ex Club Chairman Visit our Face Book Page for address and to book in https://www.facebook.com/groups/289589121226171/ http://www.neamotorsport.co.uk/ |
#51
|
|||
|
|||
Quote:
|
#52
|
||||
|
||||
You'll also need to dremel the back side of the arm near the inner hinge pin as it catches the chassis
Just make sure the arms drop under their own weight with out the shocks on |
#53
|
|||
|
|||
Without buying new diff out drives, what are people using to replace the 3.6 x 0.7 and 4.7 x 1.42 red o-rings that go on each diff out drive. Do not want to buy 3 sets of out drives, one because there's nothing wrong with my current ones and two it's about £13.00 per pair.
Any suggestions would be great, thanks. |
|
|