Lazer zxr

[DanB4]

Another

[DanB4]

And another

[DanB4]

More....

[DanB4]

More

[DanB4]

More again

[DanB4]

One more

[Naushad]

Are you sure you don't have one more too?

Lucky sod...missed out on that Lazer as you nabbed it first!

[DanB4]

Originally Posted by Naushad

Are you sure you don't have one more too?

Lucky sod...missed out on that Lazer as you nabbed it first!

Sorry!

Should look nice with new box art shell, wing, tray, gear cover and wheels/tyres

I think I'll also buy white wheels for her

[alcyon]

Originally Posted by Welshy40

Its a designers wet dream.....

sorry guys been very busy last night fixing a brand new hobbyking ESC and 8.5T motor on my optima mid becuase there is a race on sunday. still got a little setup to do on the Mid, but i think i can test fit the layshaft tonight. also welshy please get the RW B4 spur gear copied in 98 to 100T so that you can use this layshaft. You should be getting the layshaft by end of next week.

[Welshy40]

Originally Posted by DanB4

Sorry!

Should look nice with new box art shell, wing, tray, gear cover and wheels/tyres

I think I'll also buy white wheels for her

Nice, at least you have a good heatsink. Will look great when you have the above.

[Welshy40]

Originally Posted by alcyon

sorry guys been very busy last night fixing a brand new hobbyking ESC and 8.5T motor on my optima mid becuase there is a race on sunday. still got a little setup to do on the Mid, but i think i can test fit the layshaft tonight. also welshy please get the RW B4 spur gear copied in 98 to 100T so that you can use this layshaft. You should be getting the layshaft by end of next week.

Cool, ok will do, but this will work well as after ive tested in my zx im putting in my zxs to test as well and the b4 spurs will fit perfectly.

[lllyf]

Sure that you have a nice ZXR Mk2, with many upgrade options.

[alcyon]

1.Place bearing on the shaft
2.Insert into gearbox
3.Insert pulley from inner end into spline slots
4. Insert the thrust bearings
5. Secure the circlip

[alcyon]

6.place the middle part of gearbox
7. place the front pulley
8. the outer cover assembly
9. outer cover in place.
10. the 8x14 bearing in.

[alcyon]

11.fit the one way housing.
12.the associated slipper parts you will need, slipper pads not shown but required
13.how the motor end looks like
14. the first slipper plate slides in
15. the spur gear with the pads slide in

[alcyon]

16. the outer plate slide in
17. the slipper spring and the standard M3 nut- VOILA !

18. the 8x9mm shims for your 8x14mm bearings

i am glad to report that the assembly went well and the belt drive felt as smooth as the original kyosho layshaft. So its a safe bet that this layshaft is a success. Its ready to be shipped to welshy40 for real race testing. Welshy40 send me your address !!

[oli4ke]

Originally Posted by alcyon

16. the outer plate slide in
17. the slipper spring and the standard M3 nut- VOILA !

18. the 8x9mm shims for your 8x14mm bearings

i am glad to report that the assembly went well and the belt drive felt as smooth as the original kyosho layshaft. So its a safe bet that this layshaft is a success. Its ready to be shipped to welshy40 for real race testing. Welshy40 send me your address !!

AMAZING JOB, WELL DONE RAMA!!!!!!

[Welshy40]

Ace, Great that its spot on.

Its now Oosh123 and his layshaft which is going to be a bit different but just as enticing as well. Im going to have to have two cars, one with all of his designs on and the other with Alcyon's layshaft.

[oosh123]

Great Job Alcyon!

Can you please take a close up picture on the pulley and how it meshes on to the layshaft?

Thanks

[alcyon]

Originally Posted by oosh123

Great Job Alcyon!

Can you please take a close up picture on the pulley and how it meshes on to the layshaft?

Thanks

lol i am already at the office now and the layshaft has been dissambled, and i got to send it to welshy40 in a few hours time,so i cant take the pics.