|
#5541
|
|||
|
|||
Thanks very much. AFAIK the motor plate is an aftermarket part.
MmThe most important bits I'm after are kingpins and front hub carriers, any idea where I can get those? Kingpins and bearings were lost ages ago, but bearings are easy to get. |
#5542
|
||||
|
||||
Bearings i will see what size they are, i think by front hubs you mean knuckle arms where the driveshafts fit into, type in ot16 on ebay and they are there. Kin pins ive forgotten the part number but on google type in retromodelisme and look on the manual sectioon and same again search on ebay for that part number
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#5543
|
||||
|
||||
Quote:
La 235 should be easier too get Mvh isobarik |
#5544
|
|||
|
|||
Does anyone have links to zx-rr hyperclutch parts list/manual please?
Thanks
__________________
My Garage DB-01 Durga Brushless E-Maxx F103GT Clodzilla II Avante 2001 Grass Hopper II |
#5545
|
|||
|
|||
I am not sure if the ZX-S Evolution had the same clutch as the RR, but the manual claims that it is LAW-12.
http://www.kyosho.com/jpn/support/in...erzx_evo_m.pdf
__________________
NRW Offroad Cup |
#5546
|
|||
|
|||
Thanks , I know it's Law-12 , I need part number for slipper padnas UM123 is too narrow between the plates. I got LA-9 for the thrust bearing.
Ray
__________________
My Garage DB-01 Durga Brushless E-Maxx F103GT Clodzilla II Avante 2001 Grass Hopper II |
#5547
|
|||
|
|||
Hmm, that's the part numbers Do you intend to rebuild the car as a runner or as a restoration project? If it is for running only, you could cut your own slipper pads from FR4 material.
I just found the RR supplement sheet online, and the slipper looks identical to the S version. http://www.retromodelisme.com/scan_p...ho-page-2.html
__________________
NRW Offroad Cup |
#5548
|
||||
|
||||
LAW-12 hyper clutch but some parts below that I know
LAW-12-1 hyper clutch main shaft LA7 one way LA-119 hyper clutch thrust set LA-118 hyper disc plate
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#5549
|
|||
|
|||
Thanks,
It appears I have bulk of the required parts, however on the spur gear side slipper plate there is a shoulder that puts a gap between the gearbox side. The um123 doesnt fill the gap. Does anyone have pics of their spur side plate. Ray
__________________
My Garage DB-01 Durga Brushless E-Maxx F103GT Clodzilla II Avante 2001 Grass Hopper II |
#5550
|
||||
|
||||
Ray, youve confused me, upload a picture.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#5551
|
||||
|
||||
Yeah pics are definitly nedeed
Med vänlig hälsning, iso |
#5552
|
|||
|
|||
Sorry guys ,
I discovered last night the original owner super glued a small washer on to the inside of the outer slipper plate.. after careful examination I managed to remove it and the plate is now flat , this enabling UM123 slipper to sandwich nicely. The old washer was used as a locking plate as the previous person was too lazy to purchase a new pad. I now have a functional hyperclutch. Parts required LA9 thrust assembly and UM123. I will post pics later
__________________
My Garage DB-01 Durga Brushless E-Maxx F103GT Clodzilla II Avante 2001 Grass Hopper II |
#5553
|
||||
|
||||
Quote:
mvh iso |
#5554
|
||||
|
||||
Mmmm dont you mean RC10B2 slipper as i used those in my hyperclutch.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#5555
|
|||
|
|||
Got mine off the bay and wasn't too bad - $3.50 USD. Shipping was killer. Is the B2 pad similar i.d and o.d for sizing. What sort of power will the hyperclutch handle. I'm only looking at a 13.5t sensored setup.
__________________
My Garage DB-01 Durga Brushless E-Maxx F103GT Clodzilla II Avante 2001 Grass Hopper II |
#5556
|
||||
|
||||
Its identical for the hyperclutch, think the B3 is bigger
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#5557
|
||||
|
||||
Quote:
Mvh iso |
#5558
|
||||
|
||||
Sorry Iso, thats what I meant
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#5559
|
||||
|
||||
Yeah once again
Iso 1 - 0 welshy 😃😃😃😃😃 Just kidding Med vänlig hälsning, iso |
#5560
|
||||
|
||||
Hehe, one day my team will get one 😝
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
|
|