|
#201
|
||||
|
||||
Pictures of my freshly built 410v3......
The install is not great but I'll run it like this until I know that everything is fine, then I'll pull it apart and shorten all the wiring. |
#202
|
|||
|
|||
Anyone managed to get a Turnigy Trackstar (100A) into a 410? (with an Rx too...... i can get it in if i leave the Rx out.......)
|
#203
|
|||
|
|||
|
#204
|
||||
|
||||
With all the motor wire's directly hooked up to the ESC how do you guys manage to clean out your motors?
Awesome thread btw. |
#205
|
|||
|
|||
Brushless motors are pretty maintance free. The only thing I do is oil the bearings a couple times a year.
|
#206
|
||||
|
||||
Hmm. From what I have heard with sensored motors, they have holes in them so you have to take them apart after every 3-5 race days, To get out all the dirt. At least this is true on short course trucks, is it different on buggys?
|
#207
|
||||
|
||||
here's mine
|
#208
|
||||
|
||||
I have a look in mine maybe every 6 months if you are lucky, the only real maintenance I do is keeping the bearings oiled.
|
#209
|
|||
|
|||
Quote:
Plus the 410 has a removable radio tray, so you can lift the whole lot out by undoing 4 bolts and pulling the servo plug out, motor, ESC and Rx. |
#210
|
||||
|
||||
Ok thanks guys
Once I get my sensored set up in I will post pics. |
#211
|
|||
|
|||
I recently switched from mid-motor to rear-motor and I thought share pics of my Dex210 and its new electronic install
|
#212
|
||||
|
||||
My 410, just had a re-think with it last week after having a look at this thread, this is the result. I think it is much better than what i had b4.
|
#213
|
||||
|
||||
Quote:
not being picky but thought i would mention,there is a cut out near your servo saver the servo wire can pass threw save it hanging out.
__________________
Dex410r,hobbywing xtreme stock esc,lrp x12 10.5 |
#214
|
||||
|
||||
Looks good Simon, post some pictures of it with its shell on too, would be good to see it altogether
|
#215
|
|||
|
|||
Quote:
Then it failed, spectacularly. Can't get the smell of burnt electrics off my fingers now. |
#216
|
||||
|
||||
I'd love to get this thread moving again, I enjoyed looking through the differing layouts when I was setting up my Durangos.
Here are the installs on my DEX410 and DEX210 (I'll admit I had someone who is much more adept than I am solder up both buggies). 410 with a Viper VTX10 and Viper 8.5: 210 with a Tekin RSPro and a Redline 8.5:
__________________
___________________________________________ In order of appearance: Kyosho Turbo Ultima Kyosho USA-1 Axial Scorpion Axial Exo Team Durango DEX210 Team Durango DEX410 2010 Tamiya XV-01 Pro Team Durango DEX408v2 Schumacher K1 Schumacher KF Yokomo B-Max IV.3 Factory Kyosho Turbo Optima Mid |
#217
|
||||
|
||||
hi ya i did this running a small servo an can put a 4 way power cap in the gap
__________________
XTREME-RC - AVID - XFACTORY - VAMPIRE - JCONCEPTS - DMS PARTZ - BALLISTIC BUGGY - HIRO SEIKO - LUNSFORD RACING - DE RACING - REVOLUTION DESIGN RACING PRODUCTS - TEAM SR |
#218
|
|||
|
|||
Orion / Sanwa Install
Orion / Sanwa Install:
|
#219
|
||||
|
||||
Quote:
here it is in the car, i stuck my hitec atom receiver under the front prop to give me room but i just didnt like the layout Uploaded with ImageShack.us |
#220
|
||||
|
||||
That one looks like a fire risk to me. No offence chief.
__________________
PBM Racing 01773 769323 TEAM XRAY RC DISCO |
|
|