Go Back   oOple.com Forums > General > Electrics

Reply
 
Thread Tools Display Modes
  #1  
Old 31-03-2013
rapidrubberwill's Avatar
rapidrubberwill rapidrubberwill is offline
Member
 
Join Date: Dec 2011
Location: walkden manchester
Posts: 127
Default Speed passion revington r problems

Hi i was racing today after about 5 laps my car slowed down to around half power then on the last lap it died i thought may be my lipo was flat but upon checking it was ok now the esc will only turn motor if i turn the pinion first swapped the motor, lipo, sensor lead still nothing the esc only has done 30 mins. My setting have lipo cut out off temp cut out off as i know they can make the esc do funny things oh i was running a 7.5 turn motor with all the boost setting on low so it wasnt running mad settings ??????
__________________
www.rapidrubber.net
K1
Sv2
Orion
Reply With Quote
  #2  
Old 31-03-2013
braddaz's Avatar
braddaz braddaz is offline
Member
 
Join Date: Mar 2009
Posts: 81
Default

Hi
I have had this problem on mine while running at chadderton got to near last laps cut on to half power , i lowered battery voltage cut off to no improvement i would Not recommend turning it off ,i was running a 6.5t motor i ended up getting a 8.5t motor which did the bloody same in the end i turned off the overheat function this cured this problem try to make sure there is a little bit of air gap round unit if possible .
think the unit overheats do to being less burst current draw than the pro unit and blipping throttle seemed to make it worse , in instructions it says a uprated fan can be purchased but i cannot seem to find where to buy from .
i had to put a hole in shell just above fan as well .
for every body else if your thinking of buying a reventon pay the extra and get a pro if your racing
hope it helps
Reply With Quote
  #3  
Old 01-04-2013
discothesnake's Avatar
discothesnake discothesnake is offline
Mad Member
 
Join Date: May 2010
Location: Glasgow, Scotland
Posts: 1,476
Default

I've been running mine in my 2wd with a 7.5 motor and had no issues at all. I run it with the fan on.
__________________
Team Associated
Hobbywing
SRT
Reedy

My feedback
http://www.oople.com/forums/showthread.php?t=63097
Reply With Quote
  #4  
Old 01-04-2013
braddaz's Avatar
braddaz braddaz is offline
Member
 
Join Date: Mar 2009
Posts: 81
Default

hi , Discothesnake have you updated firmware on yours yet ?
Reply With Quote
  #5  
Old 01-04-2013
spud31 spud31 is offline
Senior Member
 
Join Date: Dec 2007
Posts: 458
Default

Firmware and different make sensor lead cures this
Reply With Quote
  #6  
Old 01-04-2013
discothesnake's Avatar
discothesnake discothesnake is offline
Mad Member
 
Join Date: May 2010
Location: Glasgow, Scotland
Posts: 1,476
Default

Quote:
Originally Posted by braddaz View Post
hi , Discothesnake have you updated firmware on yours yet ?
No, I've done nothing to mine at all. Mine isn't very old so not sure of it came with latest firmware.
__________________
Team Associated
Hobbywing
SRT
Reedy

My feedback
http://www.oople.com/forums/showthread.php?t=63097
Reply With Quote
  #7  
Old 01-04-2013
braddaz's Avatar
braddaz braddaz is offline
Member
 
Join Date: Mar 2009
Posts: 81
Default

Quote:
Originally Posted by spud31 View Post
Firmware and different make sensor lead cures this
when i think about it i updated my firmware to latest version and this started after that so i dont believe this cures it

is there a way to remove lastest firmware ? discothesnake do you know what version yours is on ?
Reply With Quote
  #8  
Old 01-04-2013
rapidrubberwill's Avatar
rapidrubberwill rapidrubberwill is offline
Member
 
Join Date: Dec 2011
Location: walkden manchester
Posts: 127
Default

Mines in a Couger sv2 with the fan running I updated it to latest. Firmware when I bought it had a mess with it today firmware ect still nothing just a amber light. I have the same esc in my cat sx2 running a 6.5 motor with every thing turned up no probs put the latest firmware on that today and run it then that cut out so may be its a firmware problem on that but iam sure the one out of my cougar is up the wall
__________________
www.rapidrubber.net
K1
Sv2
Orion
Reply With Quote
  #9  
Old 02-04-2013
naomiswanson naomiswanson is offline
Member
 
Join Date: Mar 2013
Posts: 12
Default

Try to check the whole parts of your car specifically the esc. Actually I've encountered this kind of problem but right after checking, it works well.
Reply With Quote
  #10  
Old 02-04-2013
rapidrubberwill's Avatar
rapidrubberwill rapidrubberwill is offline
Member
 
Join Date: Dec 2011
Location: walkden manchester
Posts: 127
Default

I fixed it I bought a orion r10 pro and the revington is being sent back je spares think it's the sensor board
__________________
www.rapidrubber.net
K1
Sv2
Orion

Last edited by rapidrubberwill; 02-04-2013 at 10:06 PM. Reason: Spelling
Reply With Quote
  #11  
Old 02-04-2013
discothesnake's Avatar
discothesnake discothesnake is offline
Mad Member
 
Join Date: May 2010
Location: Glasgow, Scotland
Posts: 1,476
Default

Quote:
Originally Posted by rapidrubberwill View Post
I fixed it I bought a orion r10 pro and the revington is being sent back je spares think it's the sensor board
That's how i would fix it too. I have three R10 speedos all approaching 2 year old and never had an issue with any of them. Best speedo around.

Saying that, my Reventon R has never let me own.
__________________
Team Associated
Hobbywing
SRT
Reedy

My feedback
http://www.oople.com/forums/showthread.php?t=63097
Reply With Quote
  #12  
Old 03-04-2013
rapidrubberwill's Avatar
rapidrubberwill rapidrubberwill is offline
Member
 
Join Date: Dec 2011
Location: walkden manchester
Posts: 127
Default

Quote:
Originally Posted by discothesnake View Post
That's how i would fix it too. I have three R10 speedos all approaching 2 year old and never had an issue with any of them. Best speedo around.

Saying that, my Reventon R has never let me own.

what set up are you running your r10 for 2wd
__________________
www.rapidrubber.net
K1
Sv2
Orion
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 02:51 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
oOple.com