|
#1
|
||||
|
||||
Spur gears ??
is anyone else having problems with spur gears stripping? i've stripped 5 so far, and at first i thought the motor clamp hadn't been tight enough and the motor had moved, but i've since moved from buttonhead to caphead screws on the motor clamp to get them really tight, but its still happened
what i noticed this time, is that the slipper has got really hot, and after its stripped the spur, it looked like it was no longer sitting dead center... on closer inspection after removing it from the car, i've noticed that the center of the spur has melted out of shape, what i want know is, are there any alternatives to the schumacher spur gears? thanks Jay
__________________
#associated #sanwa #muchmoreracing #teamorion |
#2
|
|||
|
|||
hi yes theres a few running AE spur gears most are running 81 u do have to reamer the centre hole bigger
|
#3
|
||||
|
||||
Im now running an associated spur. (81)
The schumacher ones seem quite brittle. All you have to do with the associated ones is ream the hole bigger in the middle. I find that if you make the hole so it just goes to the edge of the raised bit it is a nice fit. Make sure you drill the hole straight though! Ben
__________________
Schumacher Racing - Reedy - Schelle - TKR - Bandicoot Bodies - MIP - Nextlevelrc - Trishbits - Moss Models |
#4
|
|||
|
|||
beat u to it lil ben
|
#5
|
|||
|
|||
I know one guy who was regularly stripping spurs reset his slipper clutch properly and hasnt had a problem since. He had checked his mesh, made sure everything was tight and re-aligned the pinion.
I think if the slipper is too tight, the spur gear's teeth is the next weak link... |
#6
|
||||
|
||||
Shane.. it would appear you've caught the wrong keys and put x11 instead of SX in your sig line
__________________
Schumacher Racing - Reedy - Schelle - TKR - Bandicoot Bodies - MIP - Nextlevelrc - Trishbits - Moss Models |
#7
|
||||
|
||||
Thanks guys, i think i'll make the switch to Associated spurs...
and even better, they're a lot cheaper than schumachers Jay
__________________
#associated #sanwa #muchmoreracing #teamorion |
#8
|
||||
|
||||
Hi Jay,
Do ensure it isn't slipping excessively, it doesn't take much to melt any brand of spur. |
#9
|
|||
|
|||
Have the SX spurs shot up in price?? Ive just paid £8 for mine.Im sure they were cheaper when i first got my car??
|
#10
|
||||
|
||||
If your slipper is hot and you've melted the centre, then your slipper is far too loose. Have seen this a bit in fairness. If you get everything set right then it should all be fine. I did use AE ones when we ran out during last summer. You can use them, but it's not ideal as it's very difficult to get the hole to the right size and perfectly centre.
__________________
Matthew White |
#11
|
|||
|
|||
i stripped one first time running car but had one on now for months, i mesh mine a little tighter than i would normally
Paul
__________________
PR Racing - Insideline Racing - Zen Racing - GForce - PureRC - Puppy Paint
|
#12
|
|||
|
|||
Yes Chris a lot of the spares all went up from Schuey about two months ago now, gradually these prices are coming through as older stock at lower prices runs out now (this is the case with us anyhow)
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
#13
|
||||
|
||||
Don`t suppose anyone knows the exact reamer size ?
cheers |
#14
|
||||
|
||||
Must be 8mm in diameter
Hi, the hole must be 8mm in diameter. Looks like this:
http://www.rc-car-setup.com/index.ph...&id=30&seite=7 Greets, Chris |
#15
|
||||
|
||||
And its got to be perfectly central.
Personally ive never had a problem, but I do like my slipper to work so little it can hardly be detected. I think it'll slip 1-2ft maximum for me, and thats only to protect the belts otherwise id just lock it solid. |
#16
|
||||
|
||||
£8 for a spur gear!!!
__________________
Custom MG-Racing Associated DMS |
#17
|
||||
|
||||
£7.53 SX Spur
£3.67 B4 spur Your right. Both in stock at JE spares. To change to the B4 spur do we need to change to B4 slipper pads or are they same as SX? They look the same to the eye, I don't have them in-front of me to measure. £6.50 B4 slipper pads |
#18
|
||||
|
||||
i changed slipper pads aswel, theres a slight difference in size
__________________
#associated #sanwa #muchmoreracing #teamorion |
#19
|
||||
|
||||
But are the schumacher spur gears expensive?
X-Factory XF5506 111 tooth spur gear - black (X5) £13.95 Do the math..
__________________
Schumacher Racing - Reedy - Schelle - TKR - Bandicoot Bodies - MIP - Nextlevelrc - Trishbits - Moss Models |
#20
|
|||
|
|||
You can run associated pads, they just need filing slightly on each side. I only ran them once when i ran out of Schumacher pads.
As for the spur gears, I stripped 1 at Southport national and that was pretty much it. I know Matt did alot more in testing, but i guess that was his dodgy meshing lol. Si
__________________
Schumacher, Hobby Wing, Thunder Power, Anderson, Sanwa, Trishbits, P-Dub Racing, Rudebits, Inside Line, Nuclear RC, RC Domination, RPC |
|
|