|
#21
|
||||
|
||||
pre orders are now open on mbax2mr for shipping end of December
http://www.chubbiescarshack.co.uk/in...product_id=150
__________________
|
#22
|
||||
|
||||
eos setup from weekend
__________________
|
#23
|
|||
|
|||
What are the 'white' pistons referred to in the above sheet? |
#24
|
|||
|
|||
White piston tapered 6 holes Ref BM-S116T
|
#25
|
||||
|
||||
MB Models have them listed for pre order, expected Friday.
http://www.rccarshop.co.uk/index.php...ic/yokomo.html That should make my ordering of spares a lot easier
__________________
Race Cars: Associated B6 & B6D Vintage race cars: Associated RC10's, RC10T, B2 & T2 Kyosho Ultima XL Losi JRX2, JRX Pro & Pro SE Yokomo YZ10 94 The Veterans Inner Circle. Sponsored with Pot Noodle and Tunnocks. |
#26
|
||||
|
||||
get this week out the way and i will have a very special price on yokomo bmax4wn which will be on 5 kits only
and 1 kit with parts package www.chubbiescarshack.co.uk
__________________
|
#27
|
||||
|
||||
Is anybody having trouble removing the front hex adapters of B-Max 4? Because i can't remove them... The pin is stuck big time!
__________________
Team Yokomo B-Max2MR/Reedy/ORCA/Jconcepts/AVID Bearings Team Yokomo B-Max4III/Reedy/ORCA/Jconcepts/AVID Bearings |
#28
|
|||
|
|||
Yes, sometimes the pin is hard to get out. Try to push it out from either side with a long body clip or something similar, and if required use a hammer.
__________________
NRW Offroad Cup |
#29
|
||||
|
||||
Did you build it? If not, there's a chance that whoever did has put thread lock in it to help stop it falling out.
__________________
Team Associated Hobbywing SRT Reedy My feedback http://www.oople.com/forums/showthread.php?t=63097 |
#30
|
||||
|
||||
I built it. I was happy when i did because it was tight and i shouldn't use any type of "rubber cement" as mentioned on the guide.
Hammer and an old Associated pin will do. I'll try it tonight. I need to rebuild the cvd's.
__________________
Team Yokomo B-Max2MR/Reedy/ORCA/Jconcepts/AVID Bearings Team Yokomo B-Max4III/Reedy/ORCA/Jconcepts/AVID Bearings |
#31
|
||||
|
||||
After two meetings the car is dialed. Easy to drive and easy to get to the sweet spot of tuning. The car is "talking" to me!
A slight problem i found is the diff nut coming loose after each run. I put some loctite in there but it doesn't seem to work. I think the nut is bronze so normal loctite won't work. Any ideas?
__________________
Team Yokomo B-Max2MR/Reedy/ORCA/Jconcepts/AVID Bearings Team Yokomo B-Max4III/Reedy/ORCA/Jconcepts/AVID Bearings |
#32
|
|||
|
|||
Loctite do an activator in a spray can to help threadlock work on special metals, not sure on the price though.
|
#33
|
|||
|
|||
You could either carefully "foul" the thread on the bolt with some pliers a little or just put the tread lock on the bolt and let it dry before tightening the bolt.
__________________
NRW Offroad Cup |
#34
|
||||
|
||||
any one got a starting setup for carpet
__________________
Schumacher cougar laydown |
#35
|
||||
|
||||
Anyone come from a 410? What are your thoughts?
|
#36
|
||||
|
||||
my never run b-max4II 2012 is for sale chaps in the for sale section
personal reason forces sale only
__________________
Schumacher cougar laydown |
#37
|
||||
|
||||
are you an MB/Yokomo team driver?
__________________
Stephen Smith Answer RC Team HB Racing | Team Orion | Xpert | Racing Experience |
#38
|
||||
|
||||
__________________
Schumacher cougar laydown |
#39
|
||||
|
||||
i think u know what i was gonna question lol... changed it - good boy
__________________
Stephen Smith Answer RC Team HB Racing | Team Orion | Xpert | Racing Experience |
#40
|
||||
|
||||
you have pm
__________________
Schumacher cougar laydown |
|
|