|
#21
|
||||
|
||||
Well i cant see any specefic between the ft things..but i have not looked so close..
So i have 12 packs with this car and there is nothing like it...it is the best, but other hand i did find a descent setup . It handles like a dream in the air, it take bumps sick good.. sadly i built the rear diff not so good, so it broke, but i fixed it and it is rock solid... Cant see any reason for the CF chassi but Pimping ya car...the chassi is real stiff, and it works real good.. after 10 min of hard motor is app 80 celsius, esc app 55... Broken outdrive..fixed now..i love the gear ones.. Fixing the rear diff.. AE RC18B2...the new era? Going from 20 rear to 15.. |
#22
|
||||
|
||||
So me and my son went to the track..he used he´s new TEK18B ..little rusty, but some traingin..
I managed to get 8 packs...the weather was boiling hot... motor temp after 12-15 min of running around 85-95 celsius...way to hot, esc 65...went down from 14T to 13T piniong, still a missile...little lower temps...still hot. The car works ace, no sign of diff troubble.. |
#23
|
|||
|
|||
SWEET! Your builds are always soo cool! I want one now lol! Looks much better then the original.
__________________
Team Associated RC18B Original Kyosho Ultima (rebuilding) Traxxas Mini Revo RC boats that put my cars to shame in speed! |
#24
|
||||
|
||||
Thanks mate ...doing my best.
Im using the Futaba 3155, but mounted the micro.micro Futaba 3156, smaller, same spec on torque, but little faster (digi,metal,bb). If i am lucky, my astro turf tires will arrive today Futba 3155 New mounted smaller Futaba 3156 |
#25
|
||||
|
||||
Yes, i did find thoose tires just a few days ago...i have used them erlier, but not on Astro...The material is very! similar to Schumacher minipin/spike..
I fixed a set...what ya think ? PS, front tires needed to be cut and CA glued |
#26
|
|||
|
|||
what are those, losi step-pins?
|
#27
|
||||
|
||||
Na, they are TOPCAD DOT3 Tires...they sure look like Losis StepPins..but thoose are diffrent rubber..i think they will love the Turf
|
#28
|
|||
|
|||
Thomas how did you solder new wires to the Mongoose motor? Thanks
|
#29
|
||||
|
||||
Hi J, i have cut them only 2-2.5mm from rear end of can..and just taken of the protection yellow,orange and blu silicon"cable..so only the cables are out, as short solder tabs..so i can se the collor, still "inside" the holes where the cables are in..
not sure if it can be seen here? |
#30
|
|||
|
|||
Quote:
well done thomas. I did that same thing to mine a long time ago, as it's basically "straight-wiring" the motor ... and so as to eliminate the extra 9 connections of the motor bullet plugs that have a propensity for failure, and poor connections which hinder operation and performance |
#31
|
|||
|
|||
Ah so that's how you did it. Look great. I ought to do it but I haven't had any issues yet/
|
#34
|
||||
|
||||
6 packs today...the tires where SICK grippy...need to cut them...
Tapered pistons, i changed back, cus i used wrong oil, and they were not identical drilled as the other i use...But there is not much to say, this car, is a mean one, it is fast and it takes most of the bad bumps on our big track... |
#36
|
||||
|
||||
|
#37
|
||||
|
||||
Did one pack yesterday...the temp was killing me...only 11deg celsius at the track and windy...
tested the new Topcad DOT tires That tires worked real well on our astro track!! |
#38
|
||||
|
||||
perfect Lipos for RC18B2/SC18
Those Lipos are a perfect fit for the SC18 and RC18B2:
http://cgi.ebay.de/ws/eBayISAPI.dll?...=STRK:MEWNX:IT Here the discharge data: (10 Amps, 6,0V): capacity 2230mah, Avg Volts 7,20V, Internal Resistance 41 mOhms Here`s a pic: nic Last edited by supersonic; 02-09-2010 at 02:54 PM. Reason: pic |
#39
|
||||
|
||||
Attached is a SC18/RC18B2 Gear Chart:
nic |
#40
|
||||
|
||||
IF im gonna ran any race this season the B2 is done..new oils, new Phat wing..lowered the rear mount, better look, AE LowProfile foams...Gear diffs, 30K front 7k rear..
|
|
|