|
#321
|
||||
|
||||
guys if you are using 12mm hexs on the rear of the xmw what wheels do you use?
Do u have a part number or link to them ?and do they give the same wideness at the rear like the stock tamiya?Thanx
__________________
TRF416 TA05MS F104 TRF503 TRF201XMW TRF203 |
#322
|
|||
|
|||
__________________
Xray XB4 21 |
#323
|
||||
|
||||
Any other that will give the proper wideness to the car ?the JC are out of stock for a while.
__________________
TRF416 TA05MS F104 TRF503 TRF201XMW TRF203 |
#324
|
||||
|
||||
Hi,
If you can use the JC3348 wheels on the car, then any of the 12mm AE compatible buggy wheels should fit and keep the car legal. (I've a set of the JC3348 available if you can't find any locally. Link: http://www.msdmodels.ie/zencart/inde...yword=JC3348+0 MiCk B. :-)
__________________
http://www.dublinmodelracing.com/ (Off-road racing in Dublin) http://www.p-dubracing.co.uk (Stocking: 8Racing / AVID / GHEA / Xpert Racing / Factory R/C / Alton Design Innovations) http://www.msdmodels.ie/ (Trackside and on-line RC supplies.) |
#325
|
|||
|
|||
If you can't find the jconcepts wheels just use the associated wheels
__________________
Xray XB4 21 |
#326
|
||||
|
||||
Thanx guys ,I managed to purchase the JC wheels.
__________________
TRF416 TA05MS F104 TRF503 TRF201XMW TRF203 |
#327
|
||||
|
||||
On the setup sheet on the part TRAILING AXLE it say 0 and +1,mi correct in saying that +1 is the axle turned pointing front and 0 is pointing rear? Thanx
__________________
TRF416 TA05MS F104 TRF503 TRF201XMW TRF203 |
#328
|
||||
|
||||
The further the axle is behind the steering pin through the caster block the more trail you have. The standard set up has the least trail, if you turn the axle 180 degrees you'll create more trail. Use a set of callipers to measure the standard setting and the flip the axle to measure that. Measure from the centre pin in the caster block to the centre of the axle. Make sure the steering is centred.
__________________
Regards, David Secretary/Treasurer Southern Highlands Off Road R/C Car Club Inc. (NSW Australia) http://shorrcccinfo.wix.com/shorrccc www.facebook.com/SHORRCCC |
#329
|
||||
|
||||
What's the story regarding swapping around the rear arms ???reasons ?stock arms or different one. ?thanx
__________________
TRF416 TA05MS F104 TRF503 TRF201XMW TRF203 |
#330
|
||||
|
||||
Second time lucky ?
What slipper pads brand do u use guys ,I think my are on the way out ....I think they start to slip about 3 minutes in a race once getting hot .thanx
__________________
TRF416 TA05MS F104 TRF503 TRF201XMW TRF203 |
#331
|
||||
|
||||
Im currently building my 211XM, and i was pondering going to the Avid or Schelle slipper, would that fit on my shaft.....that kinda sounds rude lol.
lee
__________________
INSERT COIN
|
#332
|
||||
|
||||
Its seems the schelle it fits
http://www.petitrc.com/setup/tamiya/...Bristol_Build/ Waiting for confirmation if will fit stock shaft and witch is the correct Nova Clutch Sets
__________________
TRF416 TA05MS F104 TRF503 TRF201XMW TRF203 Last edited by guinness; 04-08-2015 at 10:44 AM. |
#333
|
||||
|
||||
Sure let us know dude, if it fits the stock shaft id love to try one!
lee
__________________
INSERT COIN
|
#334
|
|||
|
|||
Guinness,
Since running the 211 I've ran the AE #9603 pads without any issue. I run with the slipper very slightly loose and even in 7 minute finals, it's the same feeling throughout the run |
#335
|
||||
|
||||
Avid slipper
You need a different shaft to fit the Avid Slipper to the Tamiya gearbox. It will not fit the standard shaft...... But as moggers stated I fitted Associated pads to all my TRF 2wd buggies with no issues and very consistent throughout the run. I fitted the yellow/orange coloured pads.
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** Last edited by xfactor; 04-08-2015 at 11:31 AM. |
#336
|
||||
|
||||
Quote:
AVID Alloy RB6 top shaft*AV1020-TOP-KYO*(*needs to be modified 2,5mm on shaft side and 2mm gear side*) Moggers Thanx, will give a go as the one in the car are still the one that came with the car... BTW was hopping to see u racing at the apex Gp.
__________________
TRF416 TA05MS F104 TRF503 TRF201XMW TRF203 Last edited by guinness; 04-08-2015 at 12:00 PM. |
#337
|
||||
|
||||
Quote:
Lee
__________________
INSERT COIN
|
#338
|
||||
|
||||
What I would like to know is if the stock tamiya is to thick or thinner in diameter or shorter/longer then the Avid shaft??
__________________
TRF416 TA05MS F104 TRF503 TRF201XMW TRF203 |
#339
|
||||
|
||||
For you guys that are trying to modify the AVID top Shaft... I have several that have already been machined to fit the TRF gear box..... PM me if you need one...
__________________
TRF 501x / 502xs / 511 / 503/ 201xr/ 201xmw/ 211xm AE C4.5 Centro / AE CT4.5 Centro / T5M SDRC / SMC / Shop UFO |
|
|