|
#1
|
||||
|
||||
More Lipo Questions
Great idea getting Lipo questions answered so i`ll ask another.
Ive seen the Trakpower v balancer - can this be used in conjunction with a LRP Pulsar 3 ? |
#2
|
||||
|
||||
Hi Rich, me again. Yes the V-balancer will work in conjunction with any Lipo charger.
+ and - from charger to input of balancer, + and - of balancer to Lipo with balance lead (one supplied suits Trakpower, others available separate) and hey presto. You can use the Balancer as a stand alone - if you connect it to cells and not charger, it will equalise without charging. Its very good. Gold is nice too. |
#3
|
||||
|
||||
Great !
This whole Lipo idea is sounding much more inviting with every post. Can you tell me the best place to purchase a Trakpower B4 Lipo a B44 lipo and a V balancer ? PM if needs be - thanks Chris |
#4
|
||||
|
||||
so when are they going to do a lipo that fits in a s4 ? if they dont i dont want them to become legal
__________________
Xray xb4 18 Tenno eb410 B6.1 Merxworx mercedes indepedant specialists Www.Merxworxltd.com 01482 218000 http://www.oople.com/forums/showthread.php?t=19383 trader feedback |
#5
|
||||
|
||||
Have you tried a TrakPower 3200 saddle pack in an s4?
|
#6
|
||||
|
||||
How could that fit the 2+2+2 format?
__________________
Nortech is ACE! |
#7
|
||||
|
||||
Hi James,
I don't think that would work. Have a look at the Oswestry photos and you can see Mr.Doughty's car, the rear prop shaft is too low. |
#8
|
||||
|
||||
tell me about it
__________________
Xray xb4 18 Tenno eb410 B6.1 Merxworx mercedes indepedant specialists Www.Merxworxltd.com 01482 218000 http://www.oople.com/forums/showthread.php?t=19383 trader feedback |
#9
|
|||
|
|||
What is the height between the prop and chassis of the S4?
__________________
Yokomo - LMR |
#10
|
||||
|
||||
about three quaters of the height of a normal c cell
__________________
Xray xb4 18 Tenno eb410 B6.1 Merxworx mercedes indepedant specialists Www.Merxworxltd.com 01482 218000 http://www.oople.com/forums/showthread.php?t=19383 trader feedback |
#11
|
||||
|
||||
Just looking at 2 old disasembled cells ive got here the seem to look like there the same width pointing up as across so if the chasis on the S4 was a faction wider i recon it would be possible..
just comparing the width of 2 single cells the other way round ( across instead of facing down).
__________________
|
#12
|
||||
|
||||
I think its possible to put a stick pack lipo down the left side of the chassis on the S4 chassis. If you moved the receiver to the right side. Then you would just need a way of holding it down
__________________
Schumacher Racing - Reedy - Schelle - TKR - Bandicoot Bodies - MIP - Nextlevelrc - Trishbits - Moss Models |
#13
|
|||
|
|||
Duct Tape
What about the servo Ben
__________________
Yokomo - LMR |
#14
|
||||
|
||||
Ben doesnt use a steering servo, he leaves it and takes the corner randomly
__________________
|
#15
|
||||
|
||||
I think me and vermin decided if it was stood up it will fit
__________________
Schumacher Racing - Reedy - Schelle - TKR - Bandicoot Bodies - MIP - Nextlevelrc - Trishbits - Moss Models |
#16
|
||||
|
||||
But how bad would the car handle or perform with it like that?
__________________
|
#17
|
||||
|
||||
cant be any worse then a pred
__________________
Xray xb4 18 Tenno eb410 B6.1 Merxworx mercedes indepedant specialists Www.Merxworxltd.com 01482 218000 http://www.oople.com/forums/showthread.php?t=19383 trader feedback |
#18
|
||||
|
||||
__________________
Xray xb4 18 Tenno eb410 B6.1 Merxworx mercedes indepedant specialists Www.Merxworxltd.com 01482 218000 http://www.oople.com/forums/showthread.php?t=19383 trader feedback |
#19
|
||||
|
||||
oohhww you bitch
__________________
|
#20
|
||||
|
||||
__________________
Xray xb4 18 Tenno eb410 B6.1 Merxworx mercedes indepedant specialists Www.Merxworxltd.com 01482 218000 http://www.oople.com/forums/showthread.php?t=19383 trader feedback |
|
|