|
#1
|
||||
|
||||
Show us your B-MAX4 III
Show off your car here
__________________
A rc car is not just for christmas, it's for life
|
#2
|
||||
|
||||
Mine so far, a teaser from my upcoming photo build:
__________________
-------------------------------------------------------------------------------------------------------------------
Team Yokomo - YZ-2CAL3 | YZ-2DTM3 | YZ-4SF2 | YZ-2T | YZ-2DTM Worlds | YZ-2DTM x2 | YRX-12 x2 ------------------------------------------------------------------------------------------------------------------- 10electric | Batley Buggy Club | YORCC | RHR | MB Models --------------------------------------------------------------------------------------------------------------- |
#3
|
||||
|
||||
Looks super tasty that!!
How do you rate the quality of the kit compared to the xb4?, I hate to say it but looks even better!! |
#4
|
||||
|
||||
Quote:
For me the only "bad" bit about the bmax4 is the availability of white wheels. there are none at the moment, so i'm stuck with yellow!
__________________
-------------------------------------------------------------------------------------------------------------------
Team Yokomo - YZ-2CAL3 | YZ-2DTM3 | YZ-4SF2 | YZ-2T | YZ-2DTM Worlds | YZ-2DTM x2 | YRX-12 x2 ------------------------------------------------------------------------------------------------------------------- 10electric | Batley Buggy Club | YORCC | RHR | MB Models --------------------------------------------------------------------------------------------------------------- |
#5
|
||||
|
||||
Can't you use a hex from a TD or XB4 and use those wheels?
Thats what I did with the MR2, put on a 14mm hex and use the xray rims |
#6
|
||||
|
||||
yes need to try this with TD hexes. Seen it done on rear of mr2, but the front doesn't work with xray hexes. did you make up a spacer, or use lots of shims?
__________________
-------------------------------------------------------------------------------------------------------------------
Team Yokomo - YZ-2CAL3 | YZ-2DTM3 | YZ-4SF2 | YZ-2T | YZ-2DTM Worlds | YZ-2DTM x2 | YRX-12 x2 ------------------------------------------------------------------------------------------------------------------- 10electric | Batley Buggy Club | YORCC | RHR | MB Models --------------------------------------------------------------------------------------------------------------- |
#7
|
||||
|
||||
Working on the photo build....
Complete now and been run. It's awesome!
__________________
-------------------------------------------------------------------------------------------------------------------
Team Yokomo - YZ-2CAL3 | YZ-2DTM3 | YZ-4SF2 | YZ-2T | YZ-2DTM Worlds | YZ-2DTM x2 | YRX-12 x2 ------------------------------------------------------------------------------------------------------------------- 10electric | Batley Buggy Club | YORCC | RHR | MB Models --------------------------------------------------------------------------------------------------------------- |
#8
|
|||
|
|||
Looks like a great bit of kit. If I bought one I'd probably never get chance to race it.
Would it be naughty to buy one then, in that case?! |
#9
|
||||
|
||||
Here's mine
|
#10
|
||||
|
||||
Very nice. My body is in paint, have been using a borrowed one.
I need to re-wire also. Just transplanted the electrics right out my XB4. A few wires can be rerouted and shortened.
__________________
-------------------------------------------------------------------------------------------------------------------
Team Yokomo - YZ-2CAL3 | YZ-2DTM3 | YZ-4SF2 | YZ-2T | YZ-2DTM Worlds | YZ-2DTM x2 | YRX-12 x2 ------------------------------------------------------------------------------------------------------------------- 10electric | Batley Buggy Club | YORCC | RHR | MB Models --------------------------------------------------------------------------------------------------------------- |
#11
|
||||
|
||||
|
#12
|
||||
|
||||
Apart from the screws tho hold in the outer hinge pins where else were the cross head screws?
__________________
Team Associated Hobbywing SRT Reedy My feedback http://www.oople.com/forums/showthread.php?t=63097 |
#13
|
||||
|
||||
__________________
Team Associated Hobbywing SRT Reedy My feedback http://www.oople.com/forums/showthread.php?t=63097 |
#14
|
||||
|
||||
Quote:
pinion screws for the crown wheel and pinion outer hinge pins for the sake of those why not change them??? |
#15
|
||||
|
||||
Oh yeah, the crown gear ones are a pain in the ass. I don't recall the ones for the wing mount tho. I'm 99% sure mine were all hex heads.
__________________
Team Associated Hobbywing SRT Reedy My feedback http://www.oople.com/forums/showthread.php?t=63097 |
#16
|
||||
|
||||
Just got it as something to build really and have a go with, I quiet like the idea of the gear diffs also.
I think in my kit I got both Allen head machine screws and cross headed self tappers for my wing mounts... I obviously used the machine screws |
#17
|
|||
|
|||
I suspect I scared him into getting one as I nearly beat him. He won by 0.4sec though.
|
#18
|
|||
|
|||
I wish I was just as convincing in the speed department, but I tend to focus on demonstrating the Yokomos' durability...
|
#19
|
|||
|
|||
|
#20
|
||||
|
||||
Sylvain - B-MAX4 III
|
|
|