|
#1
|
||||
|
||||
KF2 Configuration
With the latest generation of cars like the YZ-2, XB2 and B6 running a lot more mid weight and a lighter rear end than previously. I wondered if anyone had tried a slightly different configuration in their KF2?
Rather than running the low grip set-up, I'm considering moving the motor 20mm further forward, then putting a shorty lipo in the forward position in the space where you'd put saddles? This way you'll get a bit more weight around the mid and take some away from the rear. Thoughts?
__________________
Schumacher • Phat Bodies Mendip R/C Raceway - Offroad Racing in South-West WORM-Racing - GT12 Racing in the South-West |
#2
|
||||
|
||||
ben jemmo runs kf2 kit motor position, and stubby where saddle is, details on petite rc
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD Last edited by mark christopher; 11-07-2016 at 04:37 PM. |
#3
|
||||
|
||||
You got a link? Can't seem to find it!
__________________
Schumacher • Phat Bodies Mendip R/C Raceway - Offroad Racing in South-West WORM-Racing - GT12 Racing in the South-West Last edited by Danosborne6661; 11-07-2016 at 08:44 AM. |
#4
|
||||
|
||||
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#5
|
||||
|
||||
Interesting- i wonder what length belt? I can't see any further detail from the pictures.
Edit; DOH! 117T clear as day...
__________________
Getting back to UK racing. Schumacher - Tekin - MRT - Futaba KC LayDown BossCat inbound... |
#6
|
|||
|
|||
I run the motor in kit position with a shorty lipo but use the Schumacher K2 battery straps so you can have the battery back or forward here's Bens from Petit site
http://site.petitrc.com/setup/schuma...n_RHR20150322/ |
#7
|
||||
|
||||
Quote:
My dad has also been experimenting around with removing plates from the slipper assembly in certain conditions, this could work quite well with this 117t belt set-up if you want more of a 4-gear action in slippy conditions instead of the '3.5-gear' feel. For those after the 117t, part number is U4494
__________________
Schumacher • Phat Bodies Mendip R/C Raceway - Offroad Racing in South-West WORM-Racing - GT12 Racing in the South-West Last edited by Danosborne6661; 12-07-2016 at 08:59 AM. |
#8
|
|||
|
|||
Even with the low grip layout the weight is a long way forwards, not to say there isn't an advantage to putting the motor all the way forwards if the grip on the track is there. I was thinking of trying motor forwards, but shorty at the back on astro.
|
#9
|
||||
|
||||
I've already been running 40g infront of the motor for the last little while, so makes sense for me to try the motor forward by 20mm.
The latest generation of cars are incredibly light weight on the rear end, but they seem to get round this by mounting the shock much further in on the rear tower so I may try adding a new hole!
__________________
Schumacher • Phat Bodies Mendip R/C Raceway - Offroad Racing in South-West WORM-Racing - GT12 Racing in the South-West |
#10
|
|||
|
|||
Putting the rear shocks forwards and running an LCG LiPo are also options for moving the weight forwards.
|
#11
|
||||
|
||||
Ready to test at Mendip RC Raceway tomorrow evening!
Motor moved 20mm further forward as per kit (non low grip conversion), shorty in the forward position, rear shock tower redrilled to move the shocks further in as an option. Just waiting for the 117t belt to arrive tomorrow
__________________
Schumacher • Phat Bodies Mendip R/C Raceway - Offroad Racing in South-West WORM-Racing - GT12 Racing in the South-West |
#12
|
||||
|
||||
__________________
MBModels - Schumacher Racing - Vapextech.co.uk - MRT - Savox - SMD |
#13
|
|||
|
|||
Quote:
|
#14
|
|||
|
|||
Looks good Dan, are you going to try LiPo forwards and backwards?
|
#15
|
||||
|
||||
Quote:
Extra hole inwards on the rear tower We drilled in extra hole inwards on the rear tower, a lot of the 3-gear cars have the shocks a lot more led down so we thought we would try the same. Works good with this new layout and the bumps on the track just vanished! All slipper pad weights removed except a standard dual set-up The slipper assembly works great on the low grip layout, but not so much with this new layout! With the extra forward weight AND the large slipper assembly the car was pitching forward too much. We removed all the pads except 2x like on a standard slipper set-up and used a 5mm bearing as a spacer where the spring sits to help pinch up the new set-up. Removing all the pads stops the car pitching around as much and keeps it much more neutral, was skimming over the bumps with ease now! Shorty weight under lipo I tried a few different weights under the lipo as well. 35g under the lipo tamed the car down which was nice to drive but a little lively. 70g took too much steering away and caused the rear to lean a little too much. I'll probably end up switching between 35/50g under the lipo depending on what I want the car to do. +50cst/2.5wt in front shocks With the weight being that much further forward, the car was diving quite a lot off power and actually causing the rear inside wheel to nearly lift and the geared diff to diff out! I'd suggest if you try this forward layout, you need to add +50cst weight in your front shocks to compensate Overall though the car was real good, and probably the best my KF2 has felt! I'll be running this same set-up in the wet too, will just need a few tweaks.
__________________
Schumacher • Phat Bodies Mendip R/C Raceway - Offroad Racing in South-West WORM-Racing - GT12 Racing in the South-West Last edited by Danosborne6661; 15-07-2016 at 10:54 AM. |
#16
|
||||
|
||||
Thanks for the feedback Dan, top stuff.
For the past two years, I've settled on running the KF with kit motor position (and running the shocks on the front of the rear wishbone), but running saddles, with longest wheelbase. The car has a much better balance, and rides the bumps a lot better. We run some fairly bumpy regionals here in the NE, and I've very happy with the way the car glides around the track now. My thoughts were that the rear of the car was over rotating on power in other configurations, so reducing the weight in the rear of the car, reduced the momentum of the rear of the car rotating. I played around with moving shocks from the front to the rear, but though I couldn't find a happy medium, I preferred them on the front of the wishbone, and this reduced the over rotation, and gave more steering. Last night I went to small bore rear shocks, mounted on the front of the wishbone, and this was the best it had felt. Im on 550 front oil black springs, 350 rear oil red springs (small bore). I also found running the front wishbones on long wheelbase, meant the front wasn't pitching in too much with the weight further forward. The setup seems to work well on astro, grass, carpet, and multi surface. I'm going to fit the 117T belt , and try a shorty fwd like yourself, maybe this will be going too far with moving weight fwd, considering my shock position? I hadn't thought of leaning the rear shocks in further, I might give that a go aswell. Thanks again for the feedback, Chris.
__________________
Schumacher racing http://www.racingcars.com ne-rc.blogspot.com My Trader Feedback : www.oople.com/forums/showthread.php?t=25402 |
#17
|
|||
|
|||
Thanks for posting Dan.
What rear springs and lower shock position were you running? What were you thinking for the wet? Cheers |
#18
|
|||
|
|||
I'll reply as I've been running this setup with Dan ..
We have been using mostly kit setup all round, so red rear springs on middle wishbone hole, with 3 x 1.7 pistons on 400cst oil ... and seems to work quite well on bumpy high grip astro. Moving the shocks in on a new hole in the tower loosens the back up in the turns more than kit, doesn't feel so locked in .. takes a while to get used to but seems to work with the lower rear weight bias. Taking the slipper plates out seems a really good tuning option with this layout too .. stock slipper has quite a forward kick on power .. |
#19
|
||||
|
||||
Do you think running motor forward causes a problem of the rear being too locked in though? Just wondering why you are looking to free the back end up with laid down shocks when moving weight forward, I would have thought, and have experienced the opposite to be true .... where moving the weight forward has increased steering, and so no need to free up the rear. But....... consider, my shocks are on the front of the rear wishbone.
__________________
Schumacher racing http://www.racingcars.com ne-rc.blogspot.com My Trader Feedback : www.oople.com/forums/showthread.php?t=25402 |
#20
|
|||
|
|||
It's hard to say really. Its a setup we thought up to try and get the KF to work more like the YZ2 and B6/B5m laydown ... they just seem to drive round our track (Mendip) like they're on rails ... and better over the bumps by miles !!
A more central weight gives more natural stability, moving the shocks in on the tower makes the suspension softer and more progressive and adds back in the traction plus steering .. it definitely has a good feel about it .. All I can say is try it ... its an easy conversion .. |
|
|