|
#1
|
||||
|
||||
Team Orion r10 setups
Has any one got a good settings starting point using a ballistic 6.5 motor
On 7.4v lipo
__________________
schumacer kf,savox,team Orion,dx3r |
#2
|
||||
|
||||
2wd/4wd?
I ran a 6.5 in my Centro with punch control on 2 and drag brake on 10% all other settings turned off,it was still too quick and I have now gone down to an 8.5 and it's alot smoother,it also depends on the size of track too
__________________
Iain Schumacher Laydown Schumacher Cat L1 Schumacher RC Octane |
#3
|
|||
|
|||
I've been using a setup from one of the Orion drivers to pretty good effect with my 6.5 and R10. My local track does have quite a long straight though and my centro is geared 24/78.
Drag brake 10% Punch Mode Level 5 Max Brake 75% Initial Brake drag brake Neutral range 6% Boost Timing 10 degrees Boost Start 5000rpm Turbo Timing 15 degrees Slope Rate Fastest Turbo delay 0.3s |
#4
|
||||
|
||||
Quote:
Quote:
WOW! Thats a very aggressive set up..you sure you have that right?
__________________
|
#5
|
|||
|
|||
Quote:
I'll happily take further suggestions though |
#6
|
||||
|
||||
LMAO - 7.5 motor, not 6.5!
With a 6.5 change to Punch = 3 Timing = 10 Turbo = 10 Slope = 18 Delay = 0.4 If you have a set up from me its wrong and I need to know
__________________
|
#7
|
|||
|
|||
Quote:
I'll send you an email shortly. |
#8
|
||||
|
||||
How about setting for in a 410?
Thanks |
#9
|
|||
|
|||
hi what software version are you running 110728 or 111208 cheers
|
#10
|
|||
|
|||
R10
Tony
Can you pm a setup for a 6.5 in a B44.1 as mine does not seem to be that quick JB |
#11
|
||||
|
||||
Post it don't PM then we all can learn from it
Gaz were you asking me??? Mine is a 410 V3 6.5/5.5T outdoors then prob a 7.5/8.5 indoors as our track is real tight |
#12
|
|||
|
|||
Quote:
__________________
Trader feedback - http://www.oople.com/forums/showthread.php?t=85140 |
#13
|
||||
|
||||
What would you do with a 10.5 at SHRCCC Uncle T?
__________________
Vega RB6 - Orion - Apex Models - JE Models - Cable ties
|
#14
|
||||
|
||||
Hi Neil
At SHRCC I run an Orion (obviously lol) 7.5 in 2wd with the following settings Punch = 7 Timing = 6 Turbo = 8 Slope = 12 Delay = 0.3 I belive you have recently extrended the track and I haven't had an oppotunity to race on it yet.....this setting was for your original track. Punch was turned a little more than normal as wanted the punch between the shorter corners.The turbo was turned down from normal set up as it generated too much and was close to wheelies on the high grip straight. I did though bring in the turbo earlier to get her going quicker I hope it all makes sense.......and helps
__________________
|
#15
|
|||
|
|||
As always very helpful tony! out of interest which software do you run?
__________________
Trader feedback - http://www.oople.com/forums/showthread.php?t=85140 |
#16
|
||||
|
||||
10.5t
i run a 10.5t aswell. a GM 10.5 with the r10 pro.......
Also about to fit the same to my sx3, so could you, mr tony dude, give me an idea for both the 2wd 10.5 and the 6.5 HW in the 4x4....
__________________
XB4 & MORE , Team Xray, Team Gainsy Graphics, DPP Racing 2013 & 2014 OOPLE INVERNATIONAL BEER RACE RUNNER UP! FEEDBACK LINK =
|
#17
|
||||
|
||||
Is the team Orion 90A esc going to be ok in a 2wd?
|
|
|