|
#1
|
||||
|
||||
Tekin rs pro setting
which the best setting for this speedo with feigao 6.5 motor and lipo, on very slippery track?
thanks for the help.
__________________
My Hamster "Leela" drive more better of me!!! |
#2
|
|||
|
|||
I would recommend putting on the least aggressive throttle profile so as to minimise wheel spin but you will need to set the profile and then try it and see if it suits the track i.e. no good being so non aggressive that you cannot do jumps properly! You may want to turn the timing to 0 especially if you run Lipo with the 6.5. As for drag brake settings are all down to your own preference and again change them and see if they help on the track. It is a case of trial and error.
__________________
Schumacher KC, KD, CAT XLS, CAT L1 | Team C TM2 V2, TM4, TC02 | JQ The Car | Mugen MBX6 | Losi 8T,8BE 1.5 | Durango DEX-410V4 | FTX Blaze | XRAY M18T | Kyosho STR,Surf Dude,Nexus 30 | Nimrif Makara | MFA Spear | She Devil | T-Rex 450SEV2,250SE | Ark X-400 | Protech Butterfly,Zoom 400 | Ikarus Piccolo | VW T4 | Smart 450 | KC-250 | BoltRC Kraken 5" | Emax Nighthawk 250 | Gravity 250 | S550 | Prusa i3 | TronXY X5A | Must stop collecting stuff! |
#3
|
||||
|
||||
right, 6.5, slick track, so you want to limit wheelspin
Dual mode timming 80 Limiter 80 TP 2 or 3 whats the feigao motor timing, if it is 0' turn it up a little, this will reduce torque a little too
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#4
|
||||
|
||||
I think steve is bang on there
__________________
Team Associated- HobbyWing- Reedy- CML |
#5
|
||||
|
||||
Thanks to all!
my problem is in acceleration at the exit of corner, i lost the rear of the car, because the track not have a grip. my motor feigao not have a timing mode. is a black version, with holes. the speedo have a 198 firmware. i think this motor hame more torque at initial spin....
__________________
My Hamster "Leela" drive more better of me!!! |
#6
|
||||
|
||||
either you need to go for a softer motor, or turn the limiter down, whats your limiter set to, at the moment?
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#7
|
||||
|
||||
my setting now:
drag brake =20 neutral width =min throttle prof =2 push control = off timing advance =min current limit = off dual mode enable
__________________
My Hamster "Leela" drive more better of me!!! |
#8
|
||||
|
||||
Quote:
Current limiter off will not help runnig on a low grip track i run no more than 96 on a high grip carpet track- take it down to 80 like DCM said it will feel much better for you
__________________
Team Associated- HobbyWing- Reedy- CML |
#9
|
||||
|
||||
to be fair i dont think its an esc issue it sounds like a setup issue.
Last edited by discostu; 25-06-2009 at 08:13 PM. Reason: no attachment |
#10
|
||||
|
||||
Standard factory setting. Dont go for the new setting as it rubbish! Stick with the factory setting and yellow mini pins with softer springs all round. Low ride height also helps. Dont need to change oil from carpet or grass.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#11
|
||||
|
||||
Quote:
you need the NW set to 1&2 LED on Limiter, turn down to 70 Timming to 80 (this won't affect low down torque, but give RPM)
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#12
|
||||
|
||||
i have used the mossy setup for euros 08.
mini pin yellows is not a good tyres for the italian dirty and bumpy track...
__________________
My Hamster "Leela" drive more better of me!!! |
#13
|
||||
|
||||
Well I race on a very very shiney concrete surface and have a 6.5 in and go down two spring strengths on the rear and one strength on the front. Works a treat,. Limiting can be done by the esc but it doesnt really make that much of a difference unless your totally throttle happy. Its still not going to stop wheel spin, throttle control is easily done by using your thumbs.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#14
|
||||
|
||||
What about using someones indoor carpet setting. Has anyone posted a setup for the Cat for the Petit event. If yes try that but you may prefer softening the springs, as it aids in giving a fraction more grip for cornering.
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
#15
|
||||
|
||||
it still sounds like a setup issue
|
#16
|
||||
|
||||
sorry for offtopic ... but Restimax.. do you run a Cat??
|
#17
|
||||
|
||||
Yes m8.....
this is a great car. very easy to drive on our track, with big bumpy and jump, and very slippery.
__________________
My Hamster "Leela" drive more better of me!!! |
|
|