|
#1
|
|||
|
|||
X5 PULLEY
I'm rebuilding an X5 SQUARED and was wondering what pulleys are best.
It looks to have XX4 ones in at the moment but I also have some black ones and some bigger white ones. |
#2
|
|||
|
|||
We found at the end the best ones were the XX4 rear diff pullies....
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
#3
|
|||
|
|||
I'll keep it as it is then.Should I stick with the XX4 pulley in the middle.
Thanks for helping. |
#4
|
|||
|
|||
We used XX4 pullies in the front, middle (XX4 rear diff ones on both) and centre (XX4 rear belt pulley) at the end combined with the Losi Yellow XXX4 belt. Once a belt roller was istalled close to the layshafts and one of the DMS belt cover stiffeners was fitted the transmission was the free-est it had ever been but also skipped far less than any other combination we ever ran....
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
#5
|
|||
|
|||
Ok thanks for that I'll get started as soon as I get the new spur gear.
|
#6
|
||||
|
||||
yep XX4 pulleys
but i run the blue belts i find they last longer!!!!!!!!! yellow belts r rubbish!!!!!!!!!!!! |
#7
|
||||
|
||||
Doc has been winning championships in Australia with his X - 5 for more than a year now.
|
#8
|
||||
|
||||
Can't seem to find the Blue belts anywhere
|
#9
|
||||
|
||||
I think there's a few still on the titanic
|
#10
|
||||
|
||||
Just be aware of gearing with the XX4 pulleys, you will need a surprisingly small pinion!
__________________
Nortech is ACE! |
#11
|
||||
|
||||
Quote:
__________________
Life's too short to go slow! www.ymr.no Tech Tips, HopUps & Bling Xray 2014 XB4 4WD & 2WD | B4 FTW Night Fox XL | Mugen MRX-5 | RB | Futaba 3VCS FASST | Faskolor Visit my showroom |
#12
|
|||
|
|||
When we ran our "DMS" spurs, with the AE pads instead of the Losi pucks (which were useless) then yes, no skip, little bit of slipper working initially, but lots of drive still.......
As for the blue belts a huge from me, they were the worst ones by an absolute mile, lost their teeth regular, snapped often and skipped more than a bush kangaroo, it was yellow all the way for me (just make sure it was the wider XXX4 version and NOT the thinner XXXS Touring Car one - this may have been your issue with yellow belts).
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
#13
|
||||
|
||||
I have DMS machined gears all over, dual rollers, custom made 3x belt rollers, yellow belt... but could not avoid skip unless I ran the belt REALLY tight!
AE slippers - is that B4 and just bolt on? No mods needed? That gearbox brace, does it make that much of a difference???
__________________
Life's too short to go slow! www.ymr.no Tech Tips, HopUps & Bling Xray 2014 XB4 4WD & 2WD | B4 FTW Night Fox XL | Mugen MRX-5 | RB | Futaba 3VCS FASST | Faskolor Visit my showroom |
#14
|
|||
|
|||
Quote:
Belt was set very tight (VERY tight) but the car was still "free". The AE slipper pads are what the "DMS Spurs" use (no more pucks), the only mod needed was to thin down the boss slighlty on the back of the slipper plates (since they are slighlty too long. The brace sits on top if the spur cover, we found that when ruunning the belt with lots of tension the cover would "flex" giving lots of movement up and down for the layshaft, the carbon brace we made stops the cover from flexing altogether
__________________
ORCA - LC RACING - RUDDOG PRODUCTS - JCONCEPTS - ALPHA PLUS - TEKIN RACING - ULTRAPOWER AVID R/C - VAMPIRE RACING - EXOTEK RACING - LUNSFORD RACING - X-FACTORY - TUNING HAUS - WTF AME - RAGE R/C - REVOLUTION DESIGN RACING PRODUCTS - McKUNE DESIGN - TEAM AZARASHI X-PARTZ - PHAT BODIES - RACERS EDGE - RM2 - DIRT RACING PRODUCTS - DMS INSERTZ TKR GRAPHICS - BF MATERIALS - BATAN - DMS PARTZ - TEAM AJ Tel : (01923) 816636
|
#15
|
||||
|
||||
got my belts from A-main
that is the reason Y i got rid of the XXX4 yellow belts!!!! all they did was shread teeth!!!! as the belt runs it gets more flex as the belt is made of a softer rubber or what ever the crap is made from! any way i havnt had one belt failure since running the blue belts! |
|
|