View Full Version : Cat SX Motor Heatsink
mikeyscott
16-08-2009, 03:01 PM
Hi,
Thought I saw one available for the Cat SX LIPO my Losi 7.5 was getting a tad warm today.
Also what FDR do people run with a 7.5T? I've got the standard spur fitted at the mo.
Brooks
16-08-2009, 04:10 PM
Have never seen a heatsink for the cat sx
would help get the temps down :thumbsup:
mikeyscott
16-08-2009, 04:12 PM
Darn :(
Cheers. Don't particularly want to put holes in my new shell..
Brooks
16-08-2009, 04:16 PM
Dont blame ya mate
I dont want to either :woot:
What motor are you running????
mikeyscott
16-08-2009, 04:19 PM
Losi 7.5T with a Tekin RS Pro. Didn't get hot last week with the LRP (Tekin has more advanced settings)
Standard spur and 23 pinion.
Brooks
16-08-2009, 04:30 PM
Sounds like the right gearing
I use the Lrp Sphere Tc spec speedo with 5.5 x11 lrp motor
Doesnt get really hot but could be cooler :thumbsup:
mikeyscott
16-08-2009, 04:39 PM
Sounds like the right gearing
I use the Lrp Sphere Tc spec speedo with 5.5 x11 lrp motor
Doesnt get really hot but could be cooler :thumbsup:
Gets too hot to touch it for too long. Think I'll check the Tekin set-up
Brooks
16-08-2009, 04:55 PM
Go down 1 or 2 teeth as you good kill the motor
Or get a smaller Spur Gear :woot:
mikeyscott
16-08-2009, 04:59 PM
Yeah that's what I was looking to do. Just don't understand why it runs so much hoter with a Tekin RS PRO than the LRP Sphere TC
I'll upload the config in the Tekin section later via a screen shot
discostu
16-08-2009, 05:00 PM
Go down 1 or 2 teeth as you good kill the motor
Or get a smaller Spur Gear :woot:
how would a smaller spur gear help surly you mean a bigger spur
discostu
16-08-2009, 05:09 PM
you could always get the allu gear box top for the cat if you havent got it as the rear end of the car is already a big heat sink.:thumbsup:
mikeyscott
16-08-2009, 05:13 PM
Yup added that earlier in the week
Will check to see what the Tekin boys come back with
Brooks
16-08-2009, 05:54 PM
Have got the metal rear bulkhead :p
Soz :cry: I ment get a bigger spur or pinion
Your motor sounds under Geared
mikeyscott
16-08-2009, 06:01 PM
Have got the metal rear bulkhead :p
Soz :cry: I ment get a bigger spur or pinion
Your motor sounds under Geared
OH :confused: what FDR do you you reckon I should aim for. It's pretty rapid down the main straight etc.
I'm running Trakpower 3600 LIPOs with the car and the odd Orion 4800s (may sell them so I concentrate on one cell weight)
Brooks
16-08-2009, 07:14 PM
I would stick with the standard spur
If your running on a 23, maybe go down to a 19 pinion to start with and see how hot the motor gets :woot: ( should be able to hold finger on motor for more than 5 Seconds).
Your motor could be under geared
mikeyscott
16-08-2009, 08:40 PM
What's the standard gears in the car as I'm just trying to work out FDRs?
jim76
16-08-2009, 09:13 PM
I would stick with the standard spur
If your running on a 23, maybe go down to a 19 pinion to start with and see how hot the motor gets :woot: ( should be able to hold finger on motor for more than 5 Seconds).
Your motor could be under geared
you say it's undergeared then tell him to drop 4 teeth?! :woot:
23 doesn't sound far off to me on the kit spur.
Have a look at the speedo settings, it may be running a higher punch setting etc.
Brooks
17-08-2009, 11:21 AM
Soz :blush: My fault
After thinking about it, the gearing sounds about right
look at the setting on the speedo, too much munch
Whats the timing on the motor?????
mikeyscott
17-08-2009, 11:23 AM
Soz :blush: My fault
After thinking about it, the gearing sounds about right, maybe go up 1 as you are running a 7.5t
look at the setting on the speedo, too much munch
Whats the timing on the motor?????
Can't adjust the timing on the Losi can from what I can see. It could be a punch setting on the Tekin, but the Tekin boys think the settings are fairly spot on.
What is the standard spur and gears in the cat so I can correctly give them the FDR
Brooks
17-08-2009, 11:29 AM
Thought you could mate
The standard spur is 83 with a 23 :thumbsup:
The Idler gear size are 33 tooth top & 23 tooth bottom
The ratio works out at 9.34 when running the above
mikeyscott
17-08-2009, 11:45 AM
Thought you could mate
The standard spur is 83 with a 23 :thumbsup:
http://www.racing-cars.com/images/Technical_Info/Schumacher/Current%20Cars/CAT%20SX/Instruction%20Manual/cat-sx_page_36.jpg
Brooks
17-08-2009, 11:48 AM
I know :thumbdown:
Doesnt tell you the teeth on the spur or idler gears :mad:
mikeyscott
17-08-2009, 11:51 AM
I know :thumbdown:
Doesnt tell you the teeth on the spur or idler gears :mad:
It's crap, but hey ho :(
Great car apart from that, however I still like my XXCR...
stegger
17-08-2009, 11:56 AM
You can go a bit crosseyed counting the spur gear teeth :lol::wtf::wtf:
Brooks
17-08-2009, 11:58 AM
I did mate
Lost count about 4 times :mad:
mikeyscott
17-08-2009, 01:12 PM
I did mate
Lost count about 4 times :mad:
Nightmare.. I try and count in 10 then make a mark then count another 10 and so on. Takes time, but at least you stand a better chance of getting it right.
Not difficult to mark the number on it. I like the Losi ones which are coloured
AmiSMB
17-08-2009, 02:54 PM
Schumacher used to have a CAT SX heatsink listed on the website under option parts as I tried to order these a couple of times and they were not in stock and then one day it just disappeared. I did question Robin about it at the Petit RC race last year but he did not give me a clear answer and seemed to not know what I was on about.
mikeyscott
17-08-2009, 03:00 PM
Schumacher used to have a CAT SX heatsink listed on the website under option parts as I tried to order these a couple of times and they were not in stock and then one day it just disappeared. I did question Robin about it at the Petit RC race last year but he did not give me a clear answer and seemed to not know what I was on about.
I knew I wasn't going mad...
How warm does your Tekin get in the Cat and have you done the vent hols?
Brooks
17-08-2009, 03:19 PM
Never knew they did one
I thought you were going mad!!!!! :p :thumbsup: :p
discostu
17-08-2009, 06:03 PM
i must admit its a little bit of a shame schu missied these magic touches but i personely write on them as i take them out the packet as i cant count:thumbsup::thumbsup:
AmiSMB
18-08-2009, 11:53 PM
I knew I wasn't going mad...
How warm does your Tekin get in the Cat and have you done the vent hols?
I opened up both vent holes in the shell and the RS PRO never shows more than two or three leds. The SP 6.5 gets hot but not too hot to touch but I think I am runing 21/83 and it is still insanely fast with LiPo. I am looking at an old heatink that I am not using and think that it may fit the motor if I dremel it in half. Will see how it goes :)
AmiSMB
18-08-2009, 11:57 PM
Never knew they did one
I thought you were going mad!!!!! :p :thumbsup: :p
To show you that we are definitely not mad here is a pdf from the shumacher website listing the heatsink part number H1024
Shumacher June 2008 News (http://www.racing-cars.com/images/pdf/schumacher_june_2008_news_l.pdf)
mikeyscott
19-08-2009, 07:29 AM
To show you that we are definitely not mad here is a pdf from the shumacher website listing the heatsink part number H1024
Shumacher June 2008 News (http://www.racing-cars.com/images/pdf/schumacher_june_2008_news_l.pdf)
That's it. I have just checked the manual and it's in there too. Come on Schumacher, pull your finger out!
I've dropped the 7.5 to a 22 pinion and will see how it goes.
I need to check the LEDs next time I run
MattW
19-08-2009, 10:24 AM
That isn't a specific Cat SX Part, it's just a "generic" motor heatsink that they buy in from somewhere.
Not sure if it would actually fit the car or not!!
mikeyscott
19-08-2009, 10:42 AM
typical...
Why list a part that may not fit!
MattW
19-08-2009, 11:40 AM
I'm not saying it doesn't fit - in fact it may well do! or it may not. It may fit with some adjustment, I really don't know.
mikeyscott
19-08-2009, 11:43 AM
Found a pic of it
http://www.frontlinehobbies.com.au/Shop/productImage.aspx?name=SCH-H1024
Can't see it fitting due to space etc
Mike, you could try going to the sensored mode in the RS, and run the ESC that way, but you do lose the punch control, and without the timing variable on the motor, it might get even hotter. You could also try dropping the timing down on the RS in dual mode, as I think the Losi Exceleron motors come with 15' timing as it is. (I used to run my 6.5 in sensored mode, and turned the timing advance down to 10, this kept the temps down a bit).
But sometimes, driving like an animal, can make you motor get hot, careless of the esc settings, I would think, it would be better to go to a 6.5 and let the motor work a little easier.
mikeyscott
19-08-2009, 01:14 PM
Mike, you could try going to the sensored mode in the RS, and run the ESC that way, but you do lose the punch control, and without the timing variable on the motor, it might get even hotter. You could also try dropping the timing down on the RS in dual mode, as I think the Losi Exceleron motors come with 15' timing as it is. (I used to run my 6.5 in sensored mode, and turned the timing advance down to 10, this kept the temps down a bit).
But sometimes, driving like an animal, can make you motor get hot, careless of the esc settings, I would think, it would be better to go to a 6.5 and let the motor work a little easier.
Interesting that you say this as I have been thinking along these lines and changing to a LRP 6.5 or Tekin 6.5
I did drive it harder compared with my XXCR
geerno
20-08-2009, 08:00 AM
Interesting that you say this as I have been thinking along these lines and changing to a LRP 6.5 or Tekin 6.5
I did drive it harder compared with my XXCR
Apparently the Tekin Motors run cooler. Can anyone confirm this? I have a Tekin 8.5 but it is so mild in the 4wd, I'm not surprised it doesn't get hot. Tekin motors seem mild and smooth.
LRP 5.5 works well. Runs hot and the car has plenty of zip throughout the race. Wheelstands. 22 / 80 gearing.
mikeyscott
24-08-2009, 03:47 PM
I dropped to a 22 pinion at the weekend, didn't race it (Losi XXCR day), but did a 5 min practice after racing. Very very hot motor again and Tekin was I think showing 4 LEDs
AmiSMB
24-08-2009, 04:24 PM
When I ran mine at Titchfield I ran a 6.5 SP motor with gearing 22/83 and standard internal ratio. I turned the timing down to zero on the RS Pro to stop the insane speed and to keep the heat down. Running with the Lipo packs the motor would be quite warm at the end of the run but the Tekin only showed 3 LED's. I have seen it stated by Tekin that you only have to start to worry when you get near 6 LED's.
mikeyscott
24-08-2009, 04:55 PM
I am looking at changing to a SP 6.5 with the ratio I have. Interesting about turning down the timing on the Tekin, I will look into that too.
mikeyscott
02-10-2009, 07:02 PM
Motor was mega hot last weekend again, so I'm going to put it into sensored mode with the Tekin and bring the timing down.
niggs98
02-10-2009, 07:08 PM
in sensored mode everything runs hotter. like said above stay in dual mode and take the timing to 0. that will cool it down a touch
mikeyscott
02-10-2009, 07:59 PM
in sensored mode everything runs hotter. like said above stay in dual mode and take the timing to 0. that will cool it down a touch
Sorry, my mistake. Will check and amend the settings
vBulletin® v3.8.7, Copyright ©2000-2026, vBulletin Solutions, Inc.