|
|||||||||||||||
|
#1
|
||||
|
||||
|
Hi,
Thought I saw one available for the Cat SX LIPO my Losi 7.5 was getting a tad warm today. Also what FDR do people run with a 7.5T? I've got the standard spur fitted at the mo. |
|
#2
|
||||
|
||||
|
Have never seen a heatsink for the cat sx
would help get the temps down |
|
#3
|
||||
|
||||
|
Darn
![]() Cheers. Don't particularly want to put holes in my new shell.. |
|
#4
|
||||
|
||||
|
Dont blame ya mate
I dont want to either What motor are you running???? |
|
#5
|
||||
|
||||
|
Losi 7.5T with a Tekin RS Pro. Didn't get hot last week with the LRP (Tekin has more advanced settings)
Standard spur and 23 pinion. |
|
#6
|
||||
|
||||
|
Sounds like the right gearing
I use the Lrp Sphere Tc spec speedo with 5.5 x11 lrp motor Doesnt get really hot but could be cooler |
|
#7
|
||||
|
||||
|
Gets too hot to touch it for too long. Think I'll check the Tekin set-up
|
|
#8
|
||||
|
||||
|
Go down 1 or 2 teeth as you good kill the motor
Or get a smaller Spur Gear
|
|
#9
|
||||
|
||||
|
Yeah that's what I was looking to do. Just don't understand why it runs so much hoter with a Tekin RS PRO than the LRP Sphere TC
I'll upload the config in the Tekin section later via a screen shot |
|
#10
|
||||
|
||||
|
how would a smaller spur gear help surly you mean a bigger spur
|
|
#11
|
||||
|
||||
|
you could always get the allu gear box top for the cat if you havent got it as the rear end of the car is already a big heat sink.
|
|
#12
|
||||
|
||||
|
Yup added that earlier in the week
Will check to see what the Tekin boys come back with |
|
#13
|
||||
|
||||
|
Have got the metal rear bulkhead
Soz I ment get a bigger spur or pinion Your motor sounds under Geared |
|
#14
|
||||
|
||||
|
Quote:
what FDR do you you reckon I should aim for. It's pretty rapid down the main straight etc.I'm running Trakpower 3600 LIPOs with the car and the odd Orion 4800s (may sell them so I concentrate on one cell weight) |
|
#15
|
||||
|
||||
|
I would stick with the standard spur
If your running on a 23, maybe go down to a 19 pinion to start with and see how hot the motor gets ( should be able to hold finger on motor for more than 5 Seconds).Your motor could be under geared |
|
#16
|
||||
|
||||
|
What's the standard gears in the car as I'm just trying to work out FDRs?
|
|
#17
|
|||
|
|||
|
Quote:
![]() 23 doesn't sound far off to me on the kit spur. Have a look at the speedo settings, it may be running a higher punch setting etc.
__________________
4wd - X4TE 2wd - X2C (Mad Rat passed down to son!) Ansmann Racing UK RIP - MicroTech Racing Trader Feedback |
|
#18
|
||||
|
||||
|
Soz
My fault After thinking about it, the gearing sounds about right look at the setting on the speedo, too much munch Whats the timing on the motor????? |
|
#19
|
||||
|
||||
|
Quote:
What is the standard spur and gears in the cat so I can correctly give them the FDR |
|
#20
|
||||
|
||||
|
Thought you could mate
The standard spur is 83 with a 23 The Idler gear size are 33 tooth top & 23 tooth bottom The ratio works out at 9.34 when running the above |
![]() |
|
|