oOple.com Forums

oOple.com Forums (http://www.oople.com/forums/index.php)
-   Schumacher (http://www.oople.com/forums/forumdisplay.php?f=46)
-   -   Cat SX Motor Heatsink (http://www.oople.com/forums/showthread.php?t=28938)

mikeyscott 16-08-2009 03:01 PM

Cat SX Motor Heatsink
 
Hi,

Thought I saw one available for the Cat SX LIPO my Losi 7.5 was getting a tad warm today.

Also what FDR do people run with a 7.5T? I've got the standard spur fitted at the mo.

Brooks 16-08-2009 04:10 PM

Have never seen a heatsink for the cat sx
would help get the temps down :thumbsup:

mikeyscott 16-08-2009 04:12 PM

Darn :(

Cheers. Don't particularly want to put holes in my new shell..

Brooks 16-08-2009 04:16 PM

Dont blame ya mate
I dont want to either :woot:
What motor are you running????

mikeyscott 16-08-2009 04:19 PM

Losi 7.5T with a Tekin RS Pro. Didn't get hot last week with the LRP (Tekin has more advanced settings)

Standard spur and 23 pinion.

Brooks 16-08-2009 04:30 PM

Sounds like the right gearing
I use the Lrp Sphere Tc spec speedo with 5.5 x11 lrp motor
Doesnt get really hot but could be cooler :thumbsup:

mikeyscott 16-08-2009 04:39 PM

Quote:

Originally Posted by Brooks (Post 275671)
Sounds like the right gearing
I use the Lrp Sphere Tc spec speedo with 5.5 x11 lrp motor
Doesnt get really hot but could be cooler :thumbsup:

Gets too hot to touch it for too long. Think I'll check the Tekin set-up

Brooks 16-08-2009 04:55 PM

Go down 1 or 2 teeth as you good kill the motor
Or get a smaller Spur Gear :woot:

mikeyscott 16-08-2009 04:59 PM

Yeah that's what I was looking to do. Just don't understand why it runs so much hoter with a Tekin RS PRO than the LRP Sphere TC

I'll upload the config in the Tekin section later via a screen shot

discostu 16-08-2009 05:00 PM

Quote:

Originally Posted by Brooks (Post 275680)
Go down 1 or 2 teeth as you good kill the motor
Or get a smaller Spur Gear :woot:

how would a smaller spur gear help surly you mean a bigger spur

discostu 16-08-2009 05:09 PM

you could always get the allu gear box top for the cat if you havent got it as the rear end of the car is already a big heat sink.:thumbsup:

mikeyscott 16-08-2009 05:13 PM

Yup added that earlier in the week

Will check to see what the Tekin boys come back with

Brooks 16-08-2009 05:54 PM

Have got the metal rear bulkhead :p
Soz :cry: I ment get a bigger spur or pinion
Your motor sounds under Geared

mikeyscott 16-08-2009 06:01 PM

Quote:

Originally Posted by Brooks (Post 275702)
Have got the metal rear bulkhead :p
Soz :cry: I ment get a bigger spur or pinion
Your motor sounds under Geared

OH :confused: what FDR do you you reckon I should aim for. It's pretty rapid down the main straight etc.

I'm running Trakpower 3600 LIPOs with the car and the odd Orion 4800s (may sell them so I concentrate on one cell weight)

Brooks 16-08-2009 07:14 PM

I would stick with the standard spur
If your running on a 23, maybe go down to a 19 pinion to start with and see how hot the motor gets :woot: ( should be able to hold finger on motor for more than 5 Seconds).
Your motor could be under geared

mikeyscott 16-08-2009 08:40 PM

What's the standard gears in the car as I'm just trying to work out FDRs?

jim76 16-08-2009 09:13 PM

Quote:

Originally Posted by Brooks (Post 275743)
I would stick with the standard spur
If your running on a 23, maybe go down to a 19 pinion to start with and see how hot the motor gets :woot: ( should be able to hold finger on motor for more than 5 Seconds).
Your motor could be under geared

you say it's undergeared then tell him to drop 4 teeth?! :woot:

23 doesn't sound far off to me on the kit spur.

Have a look at the speedo settings, it may be running a higher punch setting etc.

Brooks 17-08-2009 11:21 AM

Soz :blush: My fault
After thinking about it, the gearing sounds about right
look at the setting on the speedo, too much munch
Whats the timing on the motor?????

mikeyscott 17-08-2009 11:23 AM

Quote:

Originally Posted by Brooks (Post 275933)
Soz :blush: My fault
After thinking about it, the gearing sounds about right, maybe go up 1 as you are running a 7.5t
look at the setting on the speedo, too much munch
Whats the timing on the motor?????

Can't adjust the timing on the Losi can from what I can see. It could be a punch setting on the Tekin, but the Tekin boys think the settings are fairly spot on.

What is the standard spur and gears in the cat so I can correctly give them the FDR

Brooks 17-08-2009 11:29 AM

Thought you could mate
The standard spur is 83 with a 23 :thumbsup:
The Idler gear size are 33 tooth top & 23 tooth bottom
The ratio works out at 9.34 when running the above


All times are GMT. The time now is 07:23 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2026, vBulletin Solutions, Inc.
oOple.com