oOple.com Forums

oOple.com Forums (http://www.oople.com/forums/index.php)
-   Tamiya (http://www.oople.com/forums/forumdisplay.php?f=22)
-   -   Front hexs (http://www.oople.com/forums/showthread.php?t=9254)

Welshy40 19-03-2008 07:07 PM

Front hexs
 
Guys,

Where can I get alloy hexes for the TRF501x? Preferably blue? Do Losi ones fit or is the pin hole smaller?

DCM 19-03-2008 07:15 PM

I thought the 501X came with alloy hexes?

jimmy 19-03-2008 07:29 PM

no, the 501X comes with steel. Losi wont go over the axle, but you can drill them out to fit - which is what I did to mount the D4 hexes on the front of the 501X.

Welshy40 19-03-2008 09:52 PM

Quote:

Originally Posted by jimmy (Post 105444)
no, the 501X comes with steel. Losi wont go over the axle, but you can drill them out to fit - which is what I did to mount the D4 hexes on the front of the 501X.

So this doesnt affect the width of the car at all. Any ideas where I can get the D4 hexes from?

darryl 20-03-2008 01:48 PM

lost the front left wheel on my 501,but also lost the hex so having a real struggle to source the spares any help please, currently using dfo3 hex's and wheels at the moment, oh yes and finally back on line not bad eh only took me a year and a half :thumbsup:

peetbee 20-03-2008 02:41 PM

Apex Models list them, part no: HB61474, don't know if they're in stock though.
(although the desciption says steel?)

jimmy 20-03-2008 04:05 PM

they are steel yes - and will need both drilling out and the rear lip sanding slightly (lay it on a flat sheet of sand paper and move it around a bit !)

I don't remember how much they need drilling, I think it's 5mm, but they are almost that already so its pretty easy.

darryl 20-03-2008 05:31 PM

thanks for the info fellas much appreciated

jimmy 20-03-2008 05:37 PM

I think Yokomo hexes are alloy - not sure if they are a different width or not, but they also need drilling out I think to fit the Tamiya.

darryl 20-03-2008 06:06 PM

wouldnt it just be easier to use tamiya ones or are they that hard to get hold of :confused:, cause i cant find any anywhere (tamiya ones):mad:

jimmy 20-03-2008 06:09 PM

welshy was talking about alloy ones, which aren't available from Tamiya. As for replacements - well they are available but not that easily, plus they are weaker than other designs. The Hot Bodies D4 ones are much beefier, but I do have 1 or 2 sets of normal Tamiya 501X ones somewhere as well.

darryl 22-03-2008 05:54 PM

finally found a stock of tamiya front hexes steel ones tho. but none the less i found em:lol:

Welshy40 22-03-2008 08:45 PM

Quote:

Originally Posted by darryl (Post 106104)
finally found a stock of tamiya front hexes steel ones tho. but none the less i found em:lol:

Point me in the direction for the steel ones please. Im getting Losi, Hotbodies and Tamiya and will decide which suits me.

Also thanks to everyone for the information, it much appreciated. Also I have just finished a quick solder job on my Mtronics IP6 and just want feedback on what your thoughts are.

Also before anyone says it I havent got to doing the Schottky diodes yet but they will be soldered to the motor wires instead of on the motor, making life easier when putting a new motor on (I did this in the early 90's).


All times are GMT. The time now is 06:42 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2026, vBulletin Solutions, Inc.
oOple.com