|
|||||||||||||||
|
#1
|
||||
|
||||
|
Guys,
Where can I get alloy hexes for the TRF501x? Preferably blue? Do Losi ones fit or is the pin hole smaller?
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
|
#2
|
||||
|
||||
|
I thought the 501X came with alloy hexes?
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
|
#4
|
||||
|
||||
|
So this doesnt affect the width of the car at all. Any ideas where I can get the D4 hexes from?
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS |
|
#5
|
||||
|
||||
|
lost the front left wheel on my 501,but also lost the hex so having a real struggle to source the spares any help please, currently using dfo3 hex's and wheels at the moment, oh yes and finally back on line not bad eh only took me a year and a half
__________________
york offroad car club tamiya dark impact team xtreme predator x10 tenth technology predator xk98 |
|
#6
|
||||
|
||||
|
Apex Models list them, part no: HB61474, don't know if they're in stock though.
(although the desciption says steel?) |
|
#7
|
||||
|
||||
|
they are steel yes - and will need both drilling out and the rear lip sanding slightly (lay it on a flat sheet of sand paper and move it around a bit !)
I don't remember how much they need drilling, I think it's 5mm, but they are almost that already so its pretty easy. |
|
#8
|
||||
|
||||
|
thanks for the info fellas much appreciated
__________________
york offroad car club tamiya dark impact team xtreme predator x10 tenth technology predator xk98 |
|
#10
|
||||
|
||||
|
wouldnt it just be easier to use tamiya ones or are they that hard to get hold of
, cause i cant find any anywhere (tamiya ones)
__________________
york offroad car club tamiya dark impact team xtreme predator x10 tenth technology predator xk98 |
|
#11
|
||||
|
||||
|
welshy was talking about alloy ones, which aren't available from Tamiya. As for replacements - well they are available but not that easily, plus they are weaker than other designs. The Hot Bodies D4 ones are much beefier, but I do have 1 or 2 sets of normal Tamiya 501X ones somewhere as well.
|
|
#12
|
||||
|
||||
|
finally found a stock of tamiya front hexes steel ones tho. but none the less i found em
__________________
york offroad car club tamiya dark impact team xtreme predator x10 tenth technology predator xk98 |
|
#13
|
||||
|
||||
|
Quote:
Also thanks to everyone for the information, it much appreciated. Also I have just finished a quick solder job on my Mtronics IP6 and just want feedback on what your thoughts are. Also before anyone says it I havent got to doing the Schottky diodes yet but they will be soldered to the motor wires instead of on the motor, making life easier when putting a new motor on (I did this in the early 90's).
__________________
www.kamtec.co.uk www.fibre-lyte.co.uk answer-rc.com/uk/en/ Answer UK team driver Designer of the Lazer ZX/ZXR carbon fibre tub chassis Designer of the Lazer ZXRS Last edited by Welshy40; 12-09-2008 at 05:07 PM. |
![]() |
|
|