|
#241
|
||||
|
||||
For a 6.5 that seems undergeared for a 2wd car. I'd expect something more like 78/22.
__________________
Tekin Team Manager |
#242
|
|||
|
|||
Well it's ok for a bonded magnet. Slightly low but it's a rather short track. I mailed Tekin and they told me to reduce timing to 15. Now it's working fine.
|
#243
|
||||
|
||||
Guys,
New to this thread, just wondering, if I purchased an RS Pro and 5.5 redline sensored motor, do I needany aftermarket parts to run it safely? THinkin in temrs of extra Caps, if it needs a fan etc? |
#244
|
||||
|
||||
as long as you either get the hotwire and update it, or know someone with a hotwire, and update it, there is no need for extra caps or a fan, although it may be worth getting a spare cap, just in case.
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#245
|
||||
|
||||
You dont need fans on them but a few of us are running one infront of the posts, especially on a hot day on high grip/grass tracks etc.. Just helps to keep things a bit cooler. Failing that just point the solder posts towards the air vents on the bodyshell and job done. Never had a cap go on me but i guess it would never hurt to have one spare.
|
#246
|
||||
|
||||
What happens when they overheat, do they permanently die or just switch off until cool?
Doubt I'd fit a fan near the solder posts, and also wouldn't be able to get them near an air hole! |
#247
|
||||
|
||||
they shut down.
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#248
|
|||
|
|||
i have a tekin r1 pro, but the case is damaged a bit now, can i get replacements for this? if so where from??
|
#249
|
||||
|
||||
not to sure if MuchMore has any, but you may be better emailing Tekin direct.
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#250
|
||||
|
||||
You can get cases from us. $7 plus shipping.
__________________
Tekin Team Manager |
#251
|
|||
|
|||
how much would shipping be to Doncaster, South Yorkshire, England?
and do you get the two little butttons with it and decals? cheers |
#252
|
|||
|
|||
Much-More UK have these in-stock.
|
#253
|
|||
|
|||
95p shipping. You just get the case top and bottom with decal and the four screws.
|
#254
|
||||
|
||||
So how many of you are running 4wd off road this summer and getting away with no fan etc, say running 5.5 motor?
|
#255
|
||||
|
||||
I ran it yesterday, 5.5, and my fan is there to remind me the lipo is plugged in, it does no cooling, and I am lucky to see 3-4 temp LED's on.
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#256
|
||||
|
||||
Hi Randy,
What RX8 + T8 combo would you recomend for an E-Revo? Cheers, Chris. |
#257
|
||||
|
||||
On 4s most are using the 2000kv truggy system.
__________________
Tekin Team Manager |
#258
|
||||
|
||||
Hotwire
HI,
I left a post in the 'electrics' section. I've got some questions re the Hotwire. Please take a look .... Ian |
#259
|
||||
|
||||
What settings do you recommend for an RS Pro with a 7.5T Losi motor in a Cat SX LIPO?
Just need to fix the brake issues on my XXCR too. Cheers, |
#260
|
||||
|
||||
ok, the base setup for the uk is.
BS-100 NW-8 TP-3 MT-1 (Brushless fwd/brk) Timing-80 Limiter-90 Dual Mode enabled. Whats your setup on the XXCR?
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
|
|