|
#81
|
|||
|
|||
Quote:
|
#82
|
|||
|
|||
hey you should have asked me I was there. I've been running 189 in fully sensored and 5° of boost, redline 5.5 on box timing and it was ballistic, 18.4s lap in 4WD final...
|
#83
|
|||
|
|||
I believe randy meant to run in dual mode set at 80 and hae the motor's physical timing at 20°.
|
#84
|
||||
|
||||
Check: DCM is right.
I run my 5.5 in a Bj4we using 80 on the TA, dual mode. I set the motor timing at 20 on the endbell as I feel it works better there. It has NO timing effect at all once the esc is in dual mode which is in the first few inches of travel. |
#85
|
||||
|
||||
I have now a Tekin RS Pro but also bought a R1.
Will the R1 be able to handle a Castle Creations 5700kV-motor (which also is sensorless) that I still have lying around? I should think not, as the R1 has a motor limit of 5T brushless and the Tekin 5T sensorless motors are rated only at 3700 kV ... but then I have some doubts as you Tekin-guys already told earlier that motors can not always be compared by their kV-rate. |
#86
|
||||
|
||||
it depends on it's turn rating (which CC don't provide), you could try, and just keep checking the temps. What were you thinking of running it in dude?
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#87
|
||||
|
||||
in a Pred X11
|
#88
|
||||
|
||||
I think you could possibly be pushing it's limits. No harm in trying a couple of laps at a time, and seeing what the temps are like?
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#89
|
||||
|
||||
well, I guess I could, ... but I am considering workable solutions ... not something where I have to be causious all the time.
SO I learn from this that this combination "could possibly work" ... but there is a big chance the Tekin R1 will not be able to handle the basic, most used CC motor. |
#90
|
||||
|
||||
well, it all depends on the turn rating of the motor, as Kv is a mix of how many turns and rotor diameter. The Tekins have lower KV rating as the rotor diameter is significantly bigger on the Redline Sensorless to the Redline.
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#91
|
||||
|
||||
well, I guess it's maybe wurth a try. If I ever find the time to test it out, I'll post my findings here.
|
#92
|
||||
|
||||
thanks, thats a great help indeed. Just make sure you keep an eye on the temp ok, and if you can, fit a small fan in there to blow air over the solder posts.
Otherwise, it will make a great 2wd ESC.
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#93
|
||||
|
||||
yup, I'm now thinking about using it as ESC in my Tamiya M03-Swift.
I actually made a mistake and ordered the R1 where I needed a backup-ESC for my RS Pro and wanted to order the RS. I must have done something wrong (wrong click + didn't notice my error) because I got the R1. |
#94
|
|||
|
|||
Well worst that can happen is that the speedo will thermal.
|
#95
|
||||
|
||||
true
so won't harm to try. Good tip |
#96
|
||||
|
||||
We shoud be able to handle that load as long as you gear it correctly. I would make sure that it can get some air flow. Run two caps will also help esc temps.
I've run our 448 motor which is a 4T on the R1 in a wheeler. If anything it should thermal on you. I generally say as soon as you go 4wd and low turn mods like say a 6.5 it's time for a Pro. |
#97
|
||||
|
||||
just bought a Hotwire but haven't used it yet.
Is there a location, page on the teamTekin-site where one can download typical setups? Or notes on how to set up under different track-circumstances? |
#98
|
||||
|
||||
not as yet, but if you need some pointers, just ask.
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
#99
|
||||
|
||||
ok, great thx
Is it ok to ask here or do I better relocate to the Tekin-forum? |
#100
|
||||
|
||||
well, there are a few Euopean based drivers on here, or you can ask directly at Tekin too.
__________________
dragon paints : team tekin : fusion hobbies :SCHUMACHER RACING : Nuclear R/C for all my sticky and slippery stuff - if it needs gluing or lubing, Nuclear RC is the man! |
|
|