|
#1
|
||||
|
||||
Removing tyres - Boiling them - How To's
I need to now start recycling some used rims. I know many use Acetone but I have no where safe to do this with small kids about so ideally I want to boil them off.
So, how to do this ? Of course, boil, but for how long etc etc roughly. Should the water be litterally boiling away on no a very steady high simmer where the water is bubbling ? Will this affect the rim afterm aking them brittle at all ? Cheers for help, its appreciated
__________________
If you have trader feedback for me please go to http://www.oople.com/forums/showthread.php?t=120160 - Thanks Currently utilising (abusing) Durango DEX210 / KO Propo Espritt III / Tekin / LRP / SpeedPassion / Savox |
#2
|
|||
|
|||
I started boiling tyres for same reason as you re small children around and found it so effective just carried on even when children now older.
I use an old saucepan and lid as I would not want to eat food prepared in saucepan afterwards due to superglue. I slice tyres down middle to take insert out and leave whole tyre on as this gives me something to pull on once I've boiled them. I boil with a lid on for about hour and 15 mins. Tyres then come off really easy. Water needs to be bubbling the whole time so need to put lid on and gradually turn heat down until it is just bubbling and not boiling over, once you have done it once you'll know how high temp you need to leave it on. You'll need to make sure water does not boil dry - I usually boil a kettle of water about half way through to refill saucepan. I set an alarm as I am usually in garage when I am boiling tyres and once you have the smell of burnt tyres in your kitchen once you'll do the same! I also need to put extractor fan on full and leave a window open otherwise kitchen steams up. Never had a problem with brittle wheels - I've boiled associated, proline, schumacher, kyosho, Losi wheels. Rob
__________________
____________________________ Rob Warren Yokomo Cal3.1 Yokomo YZ4 SF2 |
#3
|
||||
|
||||
Thanks Rob, that answered it all. Plan to boil these on one of those portal stoves so its outdoors..and yeh old saucepan and wont be used for nothing but tyre boiling
cheers
__________________
If you have trader feedback for me please go to http://www.oople.com/forums/showthread.php?t=120160 - Thanks Currently utilising (abusing) Durango DEX210 / KO Propo Espritt III / Tekin / LRP / SpeedPassion / Savox |
#4
|
||||
|
||||
I tried boiling wheels and tires back in the 90's on my Cat 2000 wheels. Unfortunately the wheels shrunk, so haven't tried it since. However modern wheel materials may be different, so I'd advise you try it on your worst condition wheels first.
|
#5
|
||||
|
||||
i boil them if i need a speedy removal, if not then i use acetone. I fill up a shot glass of acetone, pop in the middle of an airtight container surrounded by the wheels i need rubber removed from (i cut most of the tyre off and remove inserts first), pop the lid on, then i leave the container out of harms way up on top of a kitchen cupboard. The fumes in the container soften the glue nicely
__________________
Yokomo. Nemo Racing |
#6
|
|||
|
|||
acetone for me too, soooooo easy
__________________
Trader feedback - http://www.oople.com/forums/showthread.php?t=85140 |
#7
|
||||
|
||||
£1 nail varnish remover for me, stick em in a tub, pour a bit over and leave em on the fridge with lid on. 4 hours later they peel off nicely
|
#8
|
||||
|
||||
I like the idea of acetone doing this quick, but with kids about and possible smell i need to boil them outdoors
thanks though guys for the replies
__________________
If you have trader feedback for me please go to http://www.oople.com/forums/showthread.php?t=120160 - Thanks Currently utilising (abusing) Durango DEX210 / KO Propo Espritt III / Tekin / LRP / SpeedPassion / Savox |
#9
|
||||
|
||||
I use a sealable sandwich box and get no smell at all. I take the box outside and put the tyres in so the smell does not get inside. The box I use has very tough clips as well and I just keep the acetone in there and on a high shelf out of small peoples reach.
|
#10
|
||||
|
||||
I use the oven when she's out
10 to 15 mins on 100c. Use 'rigger' gloves or similar and peel tyre from rim.
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
#11
|
||||
|
||||
same as. mine is totally airtight, no whiffs of acetone in my kitchen
__________________
Yokomo. Nemo Racing |
#12
|
|||
|
|||
Doe's boiling them have any affect on the tyre i usually use acetone but wanted to try and save some tyres of old rims if possible and acetone makes some compounds go hard so thought about boiling them
|
#13
|
||||
|
||||
I really like boiling, but results depend on how well the glue bond is (what quality glue, if the wheels and tire beads were properly cleaned, etc) - and the glue residue remains to be hard. On the wheel it's not a problem (Screwdriver, Knife, Dremel), but on the tire it is if you want to use it again.
|
#14
|
|||
|
|||
Boiling is one of my basic techniques and it is considered as a best for removing the quality of some tires. But i try to use some acetone because I am going to save some part of my tires.
|
#15
|
||||
|
||||
Always boil for 10 minutes then put into iced water for about 5 minutes,tyres fall off rims and glue residue just peels off.
__________________
Xray XB4 ,savox,speed passion 5.5 Losi 22sct,savox speed passion 10.5 Yokomo b-max 2mr,savox ,speed passion 7.5 vbc wgt 10,skyrc toro 1s, 10.5 Losi 22 2.0sct,highest servo,speed passion 6.5 yokomo yz2,highest servo,skyrc 7.5 |
#16
|
|||
|
|||
I always boil mine off .. usually around 30 mins in a pan is long enough .. only problem I've found is it can make the rims go out of "round" with some makes ... but I do it anyway
|
#17
|
||||
|
||||
No no no no , when you bake them the glue gives off cyanide, boiling and acetone is the safe way
__________________
|
#18
|
||||
|
||||
Nope, boiling does not effect the tyre
__________________
|
#19
|
|||
|
|||
+1
|
#20
|
||||
|
||||
I always boil, I done a set of 1/8th buggy wheels today and had the old tyres off and new ones glued back on the old rims in under an hour
__________________
Sworkz S350 BE1 EU - Tekin RX8 G2 - Tekin T8 G2 1900kv - Xpert SI-4531 BLS Yokomo B-Max2 MR ver2 Factory - Vampire SR1 - Vampire Type AB+ v2 7.5t - Savox SC1251 TLR 8ight T 2.0 Tekno - Tekin RX8 G2 - Tekin T8 G2 1700kv - Savox SA1283SG TLR SCTE 2.0 - Tekin RX8 G2 - Tekin Pro4 4600kv - Xpert SI-3401 BLS LC Racing EMB-1 & EMB-SC Sanwa MT4 Intellect & Gens Ace Powered |
|
|