|
#21
|
||||
|
||||
Rc10
__________________
Mitch Fiddling Team Schumacher: K2, KC, SV2, MI6 EVO Vintage Rides: Schumacher Fabiix, Losi XX CR, B2, XRS, xk98 x2, Procat, Bosscat Works, Cat 2000 EC'S, Yokomo YR-4 II, Kawada M300, XX4, Cougar 2, Schumacher Fireblade and many many more... Trader Feedback: http://www.oople.com/forums/showthread.php?t=150252
|
#22
|
||||
|
||||
That is one good looking car
mvh iso |
#23
|
||||
|
||||
Quote:
__________________
My feedback feel free to add anything http://www.oople.com/forums/showthre...863#post861863 |
#24
|
||||
|
||||
No its not for sale..... I gave it a run out Saturday at Coventry track. I was surprised how good it was to be honest. Just needs a little weight up front.....
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** |
#25
|
||||
|
||||
Really does look great Mark...👍..... Having run RC10's for years, I'm not too sure about shorty Lipos to be honest. They seem too light to me.....it seems to handle better with full length lipo...imo..
__________________
Team Associated B6 Team Associated B5m Centro C4.2 Team Associated B4.2 RC10 Worlds |
#26
|
||||
|
||||
That is a fantastic build, could you list the parts you used for the front and rear hubs. I'm building one also but I'm not sure what parts to use on the hubs. Also I'm a bit lost with shocks.. I'm using a fibre lyte Truck rear tower and worlds replica front tower. I have B44 CVDs.
|
#27
|
||||
|
||||
Quote:
REAR. Original RPM RC10T hubs Original RPM Large Bearing Set for 3/16 axles Jconcepts 12mm Hex FRONT. RC10 B4.2 30 degree castor RC10 B4.2 Front axle RC10 B4.2 Front steering arm RC10 B4.2 Front 12mm hex All very hard to find, but most are on Ebay…… Hope that helps....
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** |
#28
|
||||
|
||||
Quote:
I do have a set in the for sale that came off a RPM 91 Worlds, but are blue alloy with blue alloy tops. Front, Big bore you would need b6 rear body with b6 front shaft. This allows for the intermediate shock you need for the RPM 91 Tower. Small bore is intermediate for the RPM Tower, but if it has the hole a little lower, its for the .89 B3 front shock. Rear, The truck tower is no different in height to the buggy. The truck has a longer shock due to the travel to the wishbone (further out). So the rear buggy shock is no problem on the truck tower on the buggy ( I used to run it) For BIG BORE, You will need a set of B5/B5M shocks.... Hope that helps...
__________________
http://www.oople.com/forums/showthread.php?t=83767 TRADER FEEDBACK **** 5 Metres Speed Swimming Champion 1976**** Last edited by xfactor; 25-10-2019 at 05:15 PM. |
#29
|
||||
|
||||
Thanks Xfactor, This helps me out a lot . I'll start hunting those B4 parts and have a think about the shocks
|
#30
|
|||
|
|||
Just to add that for the front B4.2 axles JConcepts also do a part that's probably easier to find. Also, the AE parts are sometimes listed as SC10 parts, just to further confuse matters!
|
#31
|
||||
|
||||
so want another
__________________
CORNWALL Grass all the way simon mills http://www.oople.com/forums/image.ph...ine=1360240269 |
#32
|
||||
|
||||
Quote:
Thanks for the SC10 hint, also I did end up finding a pair of the Associated hex axles here in Australia.. Wasn't easy but they are on the way. The parts I don't have is probably less than the parts I do have now. I need the alloy hex mounts and shocks, some linkages etc. |
|
|