|
#1
|
||||
|
||||
Our go at a lipo X6
Our go at a lipo x6...
Here are some pics of our attempt at a lipo x6 we filled the front battery slots with some apoxy putty up to the little brace bit and then filled the rear battery slots but still allowing room for lead. We also filled the spare screw holes for the 3 gear box and put screws to hold the wing instead of the clips. And finally sprayed his shell which is still drying. here are some pics..... Ashley and Jono
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves! |
#2
|
|||
|
|||
|
#3
|
||||
|
||||
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves! |
#4
|
||||
|
||||
Looks rather cool
__________________
|
#6
|
||||
|
||||
It was unchartered ground was difficult to try and get it tidy. Jono dremmeled it i sanded it.
A
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves! |
#7
|
||||
|
||||
lol its not as bad as the photos make it look its all neat and tidy in the chassis, the wing mounts where easier than i thought they were gonna be to
__________________
|
#8
|
||||
|
||||
Looks good!
I'd move the rear camber link out though, ideally the E Speed hangers of course Is that a receiver pack???
__________________
Nortech is ACE! |
#9
|
||||
|
||||
Look like the caps that come with the Speed Passion esc's
__________________
o0ple Trader Feedback NE Venue's New & Old my space on YouTube CFR RCTV Channel Glenn Atterton BRCA 2005 1/10th Off-Road Veterans Champion LMP12 National Champion 2003/2004 / F3 class |
#10
|
||||
|
||||
Correct
__________________
Schumacher Racing - Reedy - Schelle - TKR - Bandicoot Bodies - MIP - Nextlevelrc - Trishbits - Moss Models |
#11
|
||||
|
||||
on order
__________________
|
#12
|
||||
|
||||
Where did you get the putty from mate.
|
#13
|
||||
|
||||
got from halfords its made by araldite its two part and you jus cut off what you want and mix in your hand be quick though as its rock jard in about 10mins
__________________
|
#14
|
|||
|
|||
What slipper and spur gear set up is that?
|
#15
|
||||
|
||||
Looks like an RW Racing spur with a B4 slipper set-up
__________________
|
#16
|
||||
|
||||
Losi spur and pads AE spring plates still tryhing to figure out how to fit the losi slipper.
A
__________________
Ashley Williams I always thought by 2013 we would have flying cars, but we have got blankets with sleeves! |
#17
|
||||
|
||||
Try milliput m8 in black its on flebay mold it into the slots smooth of with water and leave till morning it sets rock hard think its epoxy based
|
#18
|
||||
|
||||
Sounds like the stuff to get cheers
|
#19
|
||||
|
||||
Quote:
G
__________________
Graham North http://www.atomic-carbon.co.uk https://www.facebook.com/atomiccarbon https://www.facebook.com/nortechracing |
#20
|
||||
|
||||
Locating the spring is the only thing, you have to drill out either the small spring locator washer or the big load distributing spring locator thing. Defo need the short silver Hydra spring though.
__________________
Nortech is ACE! |
|
|