|
#261
|
||||
|
||||
As someone mentioned earlier the best fix is a bit of thread lock on the shaft to keep the pulley in place. Drive train stays nice and free and clicking disappears. Tried it all and the transmission just wasnt moving right with the shim and the noise never subsided.
__________________
...There is no off switch on a Tiger... |
#262
|
|||
|
|||
Quote:
Thanks |
#263
|
||||
|
||||
Quote:
i raced about 10 years ago and come back this year, maybe the durango was not the right car for me to start back with but now ive made the move to a SX3 it feels so much better, i dont need to push anywhere near as much to get the same if not better times with a car thats standard out the box. my durango had the lot, the next step for that car was a AC chassis kit, i spent hours getting it set up and to be fair i got it in end for indoors, i took it out doors 1 day and its was like a kangaroo all over the track, lost all heart in it and sold it the cat is getting much better every time i drive it im well happy |
#264
|
|||
|
|||
Quote:
|
#265
|
||||
|
||||
the b44 is a good car as well, if i was buying again it would be a choice of b44.1, cat sx3, or try and find a mint 511
im well happy with the car and i wont be changing any time soon |
#266
|
||||
|
||||
I came from a B44 also returning since the days of the pro/Bosscat. And I hated the B44 I Thought it to be poorly made and not very comfortable to drive. It was a tough choice between the 511 and the SX3 the winning desision was that the 511 parts can be hard to get. Very happy still learning my way round the SX3 but it is going better every time I race it.
__________________
Trader Feedback Here. |
#267
|
|||
|
|||
Cat sx3
New body and electronics.
|
#268
|
||||
|
||||
Can some other drivers post some pictures of how they have wired their SX3? I'm due to get mines this week, looking forward to the build but not too sure about the wiring. Any pics or advice greatly appreciated.
|
#269
|
|||
|
|||
I'm no expert but here's mine
|
#270
|
||||
|
||||
heres mine the PT fits between the speedo and receiver
i dont like to cut the extra servo leads so ive tucked it up under the front belt out the way with a tie strap also run the battery leads under the spur gear to the back of the chassis for the lipos hope this helps IMG00176-20110728-1850.jpg |
#271
|
|||
|
|||
Could somebody give le the dimensions of the Front and Rear Sway bars ?
I've ordered mine but it's been over a week and no signs of it I'd like to make some test on them on CAO . Thank you very much |
#272
|
|||
|
|||
I'm seriously considering getting one of these as the quality looks very good.
I run 1/8th scale (mbx6 eco & a brushless Losi 8ight T 2.0) so have never tried a belt driven car. Do they need alot of maintenance? |
#273
|
||||
|
||||
Thanks guys, looks a bit fiddly, but if I take my time and think it through, I'm sure I'll get there.
|
#274
|
|||
|
|||
leeboy44
Talking about sway bar ... I was wondering why did you mount your sway bar high on the chassis instead of the lower deck ? Thanks |
#275
|
||||
|
||||
I guess it's just down to them being more accessible and easier to change.
__________________
Retired from racing
| パベルともうします、よろしくおねがいしますスロバキア人だ、今イギリスにすんでいます。| | Ralls Racing | RCSGraphicWorx - paints, paintjobs, decals, custom wear | Schumacher Racing | Mr.O inserts | |
#276
|
||||
|
||||
Quote:
had 10 mins to swap lipos and get car ready for the next race so didnt have time to fit them tidy mechanic/driver didnt quite know where they went on the front going to check out photos to see where they go i got to be honest i love the sx3 to bits and the more i drive it the more i love it, ive not had anything go wrong with it, ive read all the tips on the belts etc so ive glued them with super glue and ive also done the chassis sides etc i need to get a few bling/trick bits for it next and see what else i can change i find the car to have to much steering hence the anti roll bar on the front so ive fitted that and im using 4.5 springs on the front with 37.5 oil before the roll bar the back end would just hook round so if anyone has got and suggestions on this would be great before i for get its for indoor carpet and wooden slippy floor thanks |
#277
|
|||
|
|||
True that the place to fit them on the front is quite well hiden (you can see the arrangement page 40 of the sx3 manual) .
What do you mean by the rear hooks round ? I've made calculation for the suspension geometry and I'm pleased with my results . But I deseperaly need the front sway bar I've ordered them more than a week ago and the salesman doesn't have them yet ... I was wondering about the slipper on the sx3 ... at what temperature should I let it run ? After a quick session outside in the garden the slipper was at 45° C is this too hot ? (a lot of on/off on the acceleration though) thanks |
#278
|
||||
|
||||
[QUOTE=shannow95;533105]True that the place to fit them on the front is quite well hiden (you can see the arrangement page 40 of the sx3 manual) .
What do you mean by the rear hooks round ? The back end felt WAY to light so it hooks round (spinning) so when i was going into corners hard under braking it would just spin the front roll bar and 4.5 springs has sorted that out now but if anyone has any tips im more the willing to try ive had time to fit the roll bar in the correct place now so its no longer on top, i would of left it there but the suspension travel was limited and it was picking up the front inside wheel on hard fast corners also to get the roll bar to work on top you need to fit the rear kit |
#279
|
||||
|
||||
I heard Moss say that a raised rear turns more. Try playing with the rear pin locations....ie role center.
__________________
SHUMACHER CAT SX SHUMACHER COUGAR SV |
#280
|
|||
|
|||
Hello ,
I need help here ... the shocks always felt kinda rubbing inside . I've opened them to see what was going on ... and all 4 shocks are full of little bit of metal . I've haven't even used it a lot . Is this a known problem ? What can I do ? Thanks |
|
|